Gigabyte GA-8S649MF-FS Manual de usuario

GA-8S649MF-FS

Intel®Pentium®4 LGA775 Processor Motherboard

User's Manual

Rev.1001

- 2 -

GA-8S649MF-FS Motherboard Layout

KB_MS ATX_12V

CPU_FAN

LGA775

BATTERY

RTL8201CL

S_ATA2

SiS 965

BIOS

PCI2

PCI3

DDR1

DDR2

S_ATA0

FDD

F_PANEL

CLR_CMOS

PCIE_16

PCI1

F_USB2

F_USB1

CODEC

COMA

LPT

AUX_IN

F_AUDIO

SiS 649

AUDIO

ATX

IDE1

USB_1394

GA-8S649MF

IT8705

SPDIF_O

SYS_FAN

USB

LAN

-FS

IDE2

Buzzer

F_1394

VT6307 SAFEMODE

S_ATA3S_ATA1

- 3 -

Block Diagram

LGA775

Processor CPUCLK+/-(200MHz)

33MHz

14.318MHz

DDR400/333/266MHz DIMM

System Bus

800MHz

SiS 649 MCHCLK (200MHz)

66MHz

48MHz

PCI Bsu

4 Serial ATA

IT 8705

ATA33/66/100

IDE Channels

PS/2

KB/Mouse

8 USB

Ports

SiS 965

PCI-

ECLK(100MHz)

PCI Express x16 DDR RAM

CODEC

Surround Speaker

Line-Out

Center / Subwoofer Speaker Out

\ MIC

Surround Speaker \ Line-In

LPT Port

Floppy

COM Port

BIOS

SPDIF Out

PCICLK(33MHz)

3 PCI

RTL

8210CL

RJ45

MII

VT6307

2 IEEE1394

GA-8S649MF-FS Motherboard - 4 -

English

CPU Supports the latest Intel®Pentium®4 LGA775 CPU

Supports Intel Pentium 4 series CPU with Hyper-Threading Technology

Supports FSB up to 800MHz

L2 cache varies with CPU

Chipset Northbridge: SiS®649 Host / Memory Controller chipset

Southbridge: SiS®965 MuTIOL

Memory 2 DDR DIMM memory slots (supports up to 2GB memory)

Supports DDR400/333/266 DIMM

Supports 2.5V DDR DIMM

Slots 1 PCI Express x 16 slot

3 PCI slots

IDE Connections 2 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of 4 IDE

devices

FDD Connections 1 FDD connection

Onboard SATA 4 Serial ATA connections

Peripherals 1 parallel port supporting Normal/EPP/ECP mode

1 COMA port

8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)

1 front audio connector

2 IEEE1394 ports (rear x 1, front x 1 via cable)

1 PS/2 keyboard port

1 PS/2 mouse port

Onboard LAN Onboard Realtek 8201CL chip (10/100 Mbit)

1 RJ 45 port

Onboard Audio ALC655 CODEC

Supports Jack Sensing function

Center/Subwoofer Speaker Out ; MIC ;

Front Speaker \ Line Out ;Surround Speaker \ Line In

AUX In \ SPDIF_O

I/O Control IT8705

Hardware Monitor System voltage detection

CPU temperature detection

CPU / System fan speed detection

CPU warning temperature

CPU / System fan failure warning

BIOS Use of licensed AWARD BIOS

Additional Features Supports @BIOS

Form Factor Micro ATX form factor; 24.4 cm x 24.4cm

1-1 FeatureSummary

Chapter 1 Hardware Installation

Hardware Installation- 5 -

English

1-2 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

ThisconnectorsupportsstandardPS/2

keyboardandPS/2mouse.

PS/2MouseConnector

(6pinFemale)

PS/2KeyboardConnector

(6pinFemale)

 USB / 1394 Connector

USB 0

USB 1

1394

Beforeyouconnectyourdevice(s)intoUSB

connector(s),pleasemakesureyour

device(s)suchasUSBkeyboard,mouse,

scanner,zip,speaker..etc.Haveastandard

USBinterface.AlsomakesureyourOS

supportsUSBcontroller.

IfyourOSdoesnotsupportUSBcontroller,

pleasecontactOSvendorforpossiblepatch

ordriverupgrade.Formoreinformation

pleasecontactyourOSordevice(s)vendors.

Serial interface standard set by Institute of Electrical and Electronics Engineers, which has

featureslikehighspeed,highbandwidthandhotplug.BecarefulwiththepolarityoftheIEEE1394

connector.CheckthepinassignmentcarefullywhileyouconnecttheIEEE1394cable,incorrect

connectionbetweenthecableandconnectorwillmakethedeviceunabletoworkorevendamage

it.ForoptionalIEEE1394cable,pleasecontactyourlocaldealer.

Hardware Installation- 6 -

English

Parallel Port, Serial Port and SPDIF (LPT/COMA/SPDIF)

Thisconnectorsupports1standardCOMport

,1Parallelportand1SPIDF.Devicelikeprinter

canbeconnectedtoParallelport;mouseand

modemetccanbeconnectedtoSerialports.

TheSPDIFoutputiscapableofprovidingdigital

audiotoexternalspeakersorcompressedAC3

datatoanexternalDolbyDigitalDecoder.

ParallelPort

(25pinFemale)

COMA

SPDIF SerialPort

(9pinMale)

Beforeyouconnectyourdevice(s)intoUSB

connector(s),pleasemakesureyour

device(s)suchasUSBkeyboard,mouse,

scanner,zip,speaker..etc.Haveastandard

USBinterface.AlsomakesureyourOS

supportsUSBcontroller.

IfyourOSdoesnotsupportUSBcontroller,

pleasecontactOSvendorforpossiblepatch

ordriverupgrade.Formoreinformation

pleasecontactyourOSordevice(s)vendors.

USB / LAN Connector LANisfastEthernetwith10/100Mbpsspeed.

USB 2

USB 3

LAN

Afterinstallonboardaudiodriver, youmay

connectspeakertoLineOutjack,micro

phone to MIC In jack.

Device like CD-ROM , walkman etc can be

connectedtoLine-Injack.

Pleasenote:

Youareabletouse2-/4-/6-channelaudio

featurebyS/Wselection.

Audio Connectors

MICIn(CenterandSubwoofer)

LineIn(RearSpeaker)

Line Out(Front Speaker)

GA-8S649MF-FS Motherboard - 7 -

English

1-3 Installation of the CPU and Heatsink

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the

wrong direction, the CPU will not insert properly. If this occurs, please change the

insert direction of the CPU.

3. Please add an even layer of heat sink paste between the CPU and heatsink.

4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise

overheating and permanent damage of the CPU may occur.

5. Please set the CPU host frequency in accordance with the processor specifications. It

is not recommended that the system bus frequency be set beyond hardware specifica

tions since it does not meet the required standards for the peripherals. If you wish to set

the frequency beyond the proper specifications, please do so according to your hard

ware specifications including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system re-

quires all of the following platform components:

- CPU: An Intel®Pentium 4 Processor with HT Technology

- Chipset: An Intel®Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Fig. 1

Gently lift the metal

lever located on the

CPU socket to the

upright position.

Metal Lever Fig. 2

Remove the plastic

covering on the CPU

socket.

Fig. 3

Notice the small gold

colored triangle lo-

cated on the edge of

the CPU socket.

Align the

Fig. 4

Once the CPU is

properly inserted,

please replace the

plastic covering and

push the metal lever

back into its original

position.

indented corner of the CPU with the triangle and

gently insert the CPU into position. (Grasping the

CPU firmly between your thumb and forefinger,

carefully place it into the socket in a straight and

downwards motion. Avoid twisting or bending

motions that might cause damage to the CPU dur-

ing installation.)

Hardware Installation- 8 -

English

1-3-2 Installation of the Heatsink

The heatsink may adhere to the CPU as a result of hardening of the heatsink paste.To prevent

such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used

for heat dissipation or using extreme care when removing the heatsink.

Fig. 6

Finally, please attach the power connector of the

heatsink to the CPU fan header located on the

motherboard.

Fig. 3

Place the heatsink atop the CPU and make sure

the push pins aim to the pin hole on the

motherboard.Pressing down the push pins di-

agonally.

Fig. 4

Please make sure the Male and Female push pin

are joined closely. (for detailed installation instruc-

tions, please refer to the heatsink installation sec-

tion of the user manual)

Fig. 5

Please check the back of motherboard after in-

stalling. If the push pin is inserted as the picture,

the installation is complete.

Fig.1

Please apply an even layer of heatsink paste on

the surface of the installed CPU.

Fig. 2

(Turning the push pin along the direction of arrow

is to remove the heatsink, on the contrary, is to

install.)

Please note the direction of arrow sign on the male

push pin doesn't face inwards before installation.

(This instruction is only for Intel boxed fan)

MalePush Pin

Female Push Pin

ThetopofFemalePushPin

GA-8S649MF-FS Motherboard - 9 -

English

1. The DIMM slot has a notch, so the DIMM

memory module can only fit in one direction.

2. Insert the DIMM memory module vertically

into the DIMM slot. Then push it down.

3. Close the plastic clip at both edges of the DIMM

slots to lock the DIMM module.

Reverse the installation steps when you wish

to remove the DIMM module.

The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory

capacity and specifications. Memory modules are designed so that they can be inserted only in one

direction. The memory capacity used can differ with each slot.

Before installing the memory modules, please comply with the following conditions:

1. Please make sure that the memory used is supported by the motherboard. It is

recommended that memory of similar capacity, specifications and brand be used.

2. Before installing or removing memory modules, please make sure that the computer

power is switched off to prevent hardware damage.

3. Memory modules have a foolproof insertion design. A memory module can be installed

in only one direction. If you are unable to insert the module, please switch the direction.

1-4 Installation of Memory

Notch

DDR

Hardware Installation- 10 -

English

1-5 ConnectorsIntroduction

1) ATX_12V

2) ATX (Power Connector)

3) CPU_FAN

4) SYS_FAN

5) FDD

6) IDE1 / IDE2

7) S_ATA0 / S_ATA1 / S_ATA2 / S_ATA3

8) F_PANEL

9) F_AUDIO

10) AUX_IN

11) F_USB1 / F_USB2

12) F_1394

13) CLR_CMOS

14) SAFE MODE

15) Battery

1112

Tabla de contenidos

Otros manuales de Placa madre de Gigabyte

Gigabyte

Gigabyte GA-6OXT Manual de usuario

Gigabyte

Gigabyte GA-M68SM-S2 Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Gigabyte

Gigabyte GA-K8VM800M Manual de usuario

Gigabyte

Gigabyte GA-8IE533 Manual de usuario

Gigabyte

Gigabyte GA-H110M-S2H-GSM Manual de usuario

Gigabyte

Gigabyte GA-6VMML Manual de usuario

Gigabyte

Gigabyte GA-946GM-DS2 Manual de usuario

Gigabyte

Gigabyte B760M C Manual de usuario

Gigabyte

Gigabyte B650 A ELITE AX ICE Manual de usuario

Gigabyte

Gigabyte GA-Z77MX-D3H TH Manual de usuario

Gigabyte

Gigabyte GA-AB350M-D3V Manual de usuario

Gigabyte

Gigabyte GA-H61MA-D2V Manual de usuario

Gigabyte

Gigabyte G1.Sniper B5 Manual de usuario

Gigabyte

Gigabyte GA-8IPE1000 Pro Manual de usuario

Gigabyte

Gigabyte GA-M55SLI-S4 Manual de usuario

Gigabyte

Gigabyte MS03-6L0 Manual de usuario

Gigabyte

Gigabyte GA-8IG1000MK Manual de usuario

Gigabyte

Gigabyte GA-F2A68HM-S1 Manual de usuario

Gigabyte

Gigabyte P4 Titan GA-8S650GXM-P-C Manual de usuario

Gigabyte

Gigabyte H510M DS2V Manual de usuario

Gigabyte

Gigabyte GA-Z270M-D3H Manual de usuario

Gigabyte

Gigabyte TRX50 AERO D Manual de usuario

Gigabyte

Gigabyte GA-8IDML Series Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario