GHM DeltaOHM HD2301.0 Manual de usuario

Operating manual

Thermohygrometer

HD2

301.0

www.deltaohm.com

English

Ke ep for future refer ence.

HD2301 - 2 - V1.7

CON TEN TS

GENERAL CHARACTERI STI CS ......................................................................... 3

DESCRI PTI ON OF TH E FUN CTI ON S ................................................................. 6

TH E PROGRAM MI N G M EN U ............................................................................. 9

PROBES AN D MEASUREMEN TS...................................................................... 1 0

MEASUREMENT OF RELATI VE HUMI DI TY................................................................. 10

PERFORMI NG THE MEASUREMENT ........................................................................ 10

CALI BRATI ON OF THE COMBI NED HUMI DI TY/TEMPERATURE PROBE ................................. 11

DI RECT I NPUT I NTO Pt 100 AND Pt 1000 TEMPERATURE PROBES ..................................... 13

TEMPERATURE MEASUREMENT............................................................................ 13

CONNECTI NG THE TP47 CONNECTOR FOR THE 4- WI RE Pt100 AND 2OR 4 - WI RE Pt1000

PROBES ......................................................................................................13

DI RECT CONNECTI ON OF 4WI RE Pt100 SENSORS ................................................... 15

W ARN I N GS .................................................................................................. 1 6

I N STRU M EN T SI GNALS AN D FAULTS ............................................................ 1 7

LOW BATTERY W ARN I N G AN D BATTERY REPLACEM EN T ............................... 1 8

WARNI NG ABOUT BATTERY USE ............................................................................. 18

I N STRU M EN T STORAGE ................................................................................ 1 9

NOTES ABOUT W ORKI N G AN D OPERATI V E SAFETY................................................. 2 0

TECH N I CAL CH ARACTERI STI CS .................................................................... 2 1

TECHNI CAL I NFORMATI ON ON THE THERMOHYGROMETER............................................... 21

TECHNI CAL DATA OF PROBES AND MODULES I N LI NE WI TH THE I NSTRUMENT........................ 22

TEMPERATURE PROBES Pt 100 SENSOR USI NG SI CRAM MODULE.................................. 22

Pt100/ Pt1000 PROBES WI TH TP47 CONNECTOR WI THOUT SI CRAM MODULE .................22

RELATI VE HUMI DI TY AND TEMPERATURE PROBES USI NG SI CRAM MODULE.........................23

ORD ERI N G COD ES ........................................................................................ 2 4

HD2301 - 3 - V1.7

GEN ERAL CH ARACTERI STI CS

The Therm ohygrom eter Model H D 2 3 0 1 .0 is a port able inst rum ent that m easures an

environm ent's t em perat ure and relat ive hum idit y.

I t is fit t ed wit h a large LCD display for ex cellent visualizat ion of t he m easured dat a.

The Therm ohygrom eter Model H D2 3 0 1 .0 m easures:

•relat ive hum idit y and t em perat ur e using com bined pr obes, fit t ed w it h a Pt 100

tem perat ure sensor or t herm ocouple;

•t em perat ure only by im m ersion, penet rat ion, or contact probes. The sensor

can be a Pt100 or Pt 1000.

When t he com bined hum idit y/ t em perat ure probe is connect ed, t he inst rum ent

calculates and displays t he follow ing data:

•absolut e hum idit y,

•dew point ,

•part ial vapour pressure.

The probes are fitt ed with t he autom at ic det ect ion SI CRAM m odule, wit h t he fact ory

calibrat ion set t ings already being m em orized inside.

The unit s of m easurem ent are t he following:

1. % RH % of relat ive hum idit y

2. g/ m 3Gram s of vapour in a cubic m eter of dry air

3. hPa Part ial vapour pressure ( hPa)

4. Td Dew point ( ° C or ° F)

5. ° C/ ° F Tem perature in Celsius ( ° C) or Fahreneit ( ° F) degrees.

Using t he Max, Min and Avg funct ion of t his inst rum ent respect ively obt ains t he

m axim um , m inim um or average values.

Ot her available funct ions are:

•t he r elat ive m easurem ent REL;

•the HOLD function;

•the autom atic t urning off which can also be disabled.

For furt her details see chapt er ‘Descript ion of the funct ions’ at page 6.

HD2301 - 4 - V1.7

Therm ohygrom eter

H D 2 3 0 1.0

HD2301 - 5 - V1.7

HD 2 3 0 1 .0

1. I nput for probes, 8-pole DI N45326 connector.

2. Bat tery sym bol: displays t he bat tery charge level.

3. Function indicators.

4. Secondary t em perat ure display line.

5. D ATA/ EN TER key: during norm al operat ion displays t he m ax im um ( MAX) , t he

m inim um ( MI N) and t he average ( AVG) of current m easurem ents; in t he m enu,

confirm s t he current select ion.

6. CLR/ ESC key: during norm al operat ion r esets t he m axim um , t he m inim um and

t he average of current m easurem ent s; in t he m enu, it reset s t he value set with t he

arrows.

7. H OLD/ key : freezes t he m easur em ent display during nor m al oper at ion; in t he

m enu, increases t he current value.

8. U N I T/ MEN U key : it allows select ion of t he unit of m easur em ent ; w hen pressed

together wit h the DATA key, it allows t o open t he m enu.

9. REL/ key : during nor m al operat ion enables t he r elat ive m easurem ent ( displays

the difference between the current value and the logged value when t he key is

pressed) ; in t he m enu, decreases t he current value.

10.ON -OFF/ AUTO-OFF key: t urns the instrum ent on and off; when pressed t ogether

wit h t he HOLD key, disables t he AutoPowerOff funct ion.

11.MAX ( m axim um v alue) , MI N ( m inim um v alue) and AV G ( aver age value) sym bols.

12.Main display line of r elat iv e hum idit y and ot her der ived m easurem ent s.

13.Line for sym bols and com m ent s.

HD2301 - 6 - V1.7

DESCRI PTI ON OF TH E FUN CTI ON S

The keyboard of the therm ohygrom eter HD 2 3 0 1 .0 is com posed of double-funct ion

keys. The function on t he key is the "m ain function", while t he one above the key is

the "secondary function".

When t he inst rum ent is in st andard m easurem ent m ode, t he m ain funct ion is act ive.

I n t he m enu, the secondary funct ion is enabled; press the D ATA+ UN I T keys toget her

t o open t he m enu.

The pressing of a k ey is accom panied by a short confirm at ion " beep" : a longer " beep"

sounds if the wrong key is pressed. Each key specific funct ion is described in det ail

below.

This key has two functions:

•ON / OFF: press t his key to turn t he inst rum ent on and off.

The t urning on enables all display segm ents for a few seconds, st ar ts an Au t o-t est

including the det ect ion of t he probe connect ed t o the input, and sets the inst rum ent

ready for norm al m easurem ent .

MIN

min s

>>>

•AUTO/ OFF: the Au t oPow e r Off funct ion can be disabled by sim ult aneously

pressing this key and the "HOLD" key when t urning t he inst rum ent on.

During t urning on, should no probes be connect ed, the "N O_ PRBE_ SER_ N UM"

m essage is displayed in t he line for sym bols for a few seconds, and in t he m ain line a

series of dashes appears while t he "ERR" m essage replaces t he tem perat ure.

When t he probe is inserted int o a funct ioning inst rum ent , t he " NEW _ PROB_ DET"

( New pr obe det ect ed) m essage appears: as t he dat a are captur ed upon t ur ning t he

inst rum ent on, it is necessary to turn it off and on again.

Caution! Replace the probes when the inst rum ent is off.

ON - OFF a nd AUTO- OFF

HD2301 - 7 - V1.7

The inst rum ent has an AutoPowerOff funct ion t hat aut om at ically turns t he inst rum ent

off aft er about 8 m inutes if no key is pressed during the intervening t im e.

Press sim ult aneously the ON / OFF key and the HOLD key t o disable t h is f unct ion.

I n this case, rem em ber t o t urn t he inst rum ent off using t he ON / OFF key: disabling of

t he aut om at ic turning off is shown by the blinking bat tery sym bol.

The CLR key has t wo funct ions:

•CLEAR ( CLR) : allows t o reset t he m axim um ( MAX) , m inim um ( MI N) and average

( AVG) value of t he capt ur ed m easurem ent s;

•ESC: once t he MENU has been opened with t he D ATA+ UN I T keys, the CLR key

will allow to cancel the param eters set using the and arrows.

The DATA key is used for the following funct ions:

•DATA: during norm al m easurem ent, by pressing t his key once t he m axim um

( MAX) value of t he m easurem ent s capt ur ed by t he probe connect ed t o t he

inst rum ent is displayed, updat ing it w it h t he acquisit ion of new sam ples;

- by pressing t his key again the m inim um ( MI N) value is displayed;

- by pressing t his key a t hird t im e t he average ( AVG) v alue is display ed.

The acquisit ion frequency is once a second.

The MAX, MI N and AVG values rem ain in t he m em ory until t he inst rum ent is on,

ev en aft er exit ing t he DATA display funct ion. When t he inst rum ent is off, t he

previously m em orized data are cleared. Upon turning on, t he inst rum ent

autom atically st art s m em orizing the MAX, MI N and AVG values.

To reset the previous values and st art wit h a new measurem ent session, press

CLR unt il t he FUNC_ CLRD m essage appears.

•EN TER: once t he MENU has been opened with the D ATA+ UN I T keys, t he DATA

key will perform the ENTER funct ion and t he MENU can be browsed and the

displayed param et er confirm ed.

The H OLD key is used for t he following funct ions:

•HOLD: by pressing t his key t he current m easurem ent updat e is st opped and t he

"HOLD" m essage will appear in the upper left -hand corner of the display. To return

t o t he current m easurem ent , press t he key again.

D ATA/ EN TER k ey

HOLD/ 

D isa blin g of t he a ut om a t ic t u rnin g off

CLR/ ESC k e y

HD2301 - 8 - V1.7

•: once t he MENU has been opened wit h the D ATA+ U N I T keys, t he key will

allow t o increase t he value of the select ed param et er.

Pressed toget her with t he ON / OFF key, during turn on, t he Aut oPowerOff funct ion is

disabled (see t he descript ion of t he ON/ OFF key).

The UN I T key is used for the following functions:

•UN I T: by pr essing t his key t he unit of m easurem ent of t he m ain input quant it y is

select ed: t he unit of m easurem ent will appear in t he upper par t of t he display; t he

m easured value will be displayed in t he cent ral line. By repeat edly pressing t he

UN I Tkey, t he desired unit of m easurem ent can be select ed bet ween t he

follow ing:

1. % RH % of relat ive hum idit y

2. g/ m 3Gram s of vapour in a cubic m eter of dry air

3. hPA Part ial vapour pr essur e ( hPa)

4. Td Dew point ( ° C or ° F)

By now pressing UNI T, t he % RH unit of m easurem ent is displayed again in t he

com m ent line and, sim ult aneously, t he unit of t em perat ure m easurem ent blinks.

Use the and arrows, if you w ish t o change t he t em perature display from

degrees Celsius ( ° C) to degrees Fahreneit ( ° F), or vice-versa. Confirm by pressing

the UNI T key or wait for the unit of m easurem ent t o st op blinking ( about 15

seconds t im eout ) .

•M EN U : in the m enu t wo it em s can be set :

1. Probe t ype

2. Probe ca librat ion

- t he m enu is opened by pressing sim ult aneously D ATA+ U N I T: t he first it em of t he

inst rum ent program m ing m enu will appear;

- use t he and arrows ( r espect ively locat ed above t he HOLD and REL keys) t o

m odify t he display ed value;

- press D ATA/ ENTER to confir m t he m odification and go onto the next it em ;

- press CLR/ ESC to cancel t he m odificat ion;

- to e x it t he m enu, press t he U N I T/ M EN U key again.

The " REL" key is used for the following funct ions:

•REL: it displays t he difference bet ween t he current value and t hat m easured on

pressing the key. The "REL" m essage is displayed on t he left . To ret urn t o t he

norm al m easurem ent , press t he key again.

•: once the MENU has been opened wit h t he D ATA+ UN I T keys, t he key will

allow t o decrease t he value of t he select ed param eter .

REL/ key

UN I T/ M EN U

HD2301 - 9 - V1.7

THE PROGRAM M I N G M EN U

To access t o t he m enu press sim ult aneously the following keys:

The it em s t o be set are list ed in t his order:

1 . Pr obe t ype :the "PRBE_ TYPE" m essage is displayed in t he com m ent line. The

m ain line in t he cent er of t he display shows t he t ype of probe connect ed t o t he

inst rum ent. The following probes can be connect ed t o t he input :

•hum idit y/ t em perat ure com bined probes wit h " Pt100" sensor com plet e w it h

SI CRAM m odule

•t em perat ure probes " Pt100" com plet e wit h SI CRAM m odule

•direct 4 w ir e "Pt 100" probes com plet e wit h TP47 m odule

•2 or 4 wire " Pt 1000" probes com plet e wit h TP47 m odule

N OTE: The probes fit ted w it h SI CRAM m odule are autom at ically det ect ed by t he

inst rum ent upon t urning on. The type of probe is configured by t he inst rum ent and

cannot be m odified by t he user.

I f the direct 4 wire "Pt100" probes and the " Pt 1000" pr obes that are not

m anufact ured by Delta OHM are connect ed t o the inst rum ent , t he

N O_ PRBE_ SER_ NUM m essage is displayed. I n t his case t he probe t ype m ust be

ent ered m anually by t he user:

•use t he and ar row s ( respect ively locat ed above t he HOLD and REL keys)

to m odify t he type of probe;

•press D ATA/ EN TER t o confir m t he m odificat ion and go ont o t he next it em ;

•press CLR/ ESC to cance l t he m odificat ion;

•to e x it t he m enu, press t he UN I T/ M EN U key again.

2 . Use r calibr a t ion procedure of th e com bine d h um id it y / t e m p er at ure

probe: t he probes are calibrated in our laboratory at 23 ° C at t he relat iv e

hum idit y point s of 75% RH, 33% RH and 11.4% RH. On request , t he probes

can be checked at different isot herm s.

For t h e Ca librat ion se que nce , se e par agr a ph ‘Ca libr at ion of t he com bined

hum idit y/ t e m peratu r e probe’ a t page 1 1 .

HD2301 - 10 - V1.7

PROBES AN D M EASUREM EN TS

The inst rum ent HD2 3 0 1 .0 works by using com bined hum idit y/ t em perat ur e probes

( tem perat ure with a Pt 100 sensor) and wit h t em perat ure only probes w it h 4 w ir e

Pt 100, or 2 or 4 wire Pt 1000.

The com bined hum idity/ t em perat ure probes are fit t ed w it h SI CRAM m odule t hat act s

as an interface between the sensor on t he probe and t he inst rum ent . There is a

m icroprocessor circuit wit h a perm anent m em or y inside t he m odule t hat enables t he

inst rum ent to recognize t he type of probe connected and t o read its calibrat ion

inform at ion.

The Delt a OHM Pt1000 probes ar e aut om at ically det ect ed while t he dir ect 4 wir e Pt 100

t em perat ure probe is not aut om at ically detect ed by t he inst rum ent and m ust be set

up in the Pr obe t y pe m enu it em ( please see the m enu descript ion on prev ious

chapt er) .

The probe is detect ed durin g turn on, and this cannot be perform e d w hen the

in st r um e nt is a lr e ady on, t h e refor e if a p rob e is connect ed and t he

instrum ent is on, it is necessary to turn it off and on.

MEASU REM EN T O F RELATI VE H UM I DI TY

The hum idit y probes are "hum idity and tem perat ure" com bined pr obes:

•t he hum idit y sensor is a capacit at iv e t ype sensor ;

•the t em perat ure sensor is a Pt 100.

The inst rum ent m easures relat ive hum idit y % RH and t em perat ur e, and st ar t ing fr om

t he fixed barom et ric pressure value of 1013.25 m bar it calculates t he following

result ing quant it ies:

1. g/ m 3gram s of vapour in a cubic m eter of dry air

2. hPa Part ial vapour pressure ( hPa)

3. Td Dew point ( ° C or ° F)

PERFORM I N G TH E M EASUREM EN T

To perform t he m easurem ent , proceed as follow s:

1. introduce the probe in the area of whose param eters you wish t o m easure.

Ca u t ion!Keep the probe far from elem ents that m ight interfere wit h m easurem ent

such as: heat or sources of cooling, walls, air-st ream s, et c

Avoid t em pe r a t ure drops that m igh t ca u se condensation.

2. a reading taken when no heat drop occurs is pract ically im m ediat e;

N OTE: in condit ions involv in g he a t drops, it is necessary t o wait until the probes and

their housing have reached a therm al equilibrium in order to prevent heat irradiat ion

or absorpt ion on t he relative hum idit y sensor which would cause a fau lt y

m easure m en t .

3. since tem perat ure affect s relat ive hum idit y; m ove the probe like a fan in order to

speed t he response t im e in t he presence of heat drops.

Tabla de contenidos

Otros manuales de Instrumento de medición de GHM

GHM

GHM DeltaOHM HD2305.0 Manual de usuario

GHM

GHM DeltaOHM LPPHOT02 Manual de usuario

GHM

GHM Delta OHM PYRAsense LPS10 Series Manual de usuario

GHM

GHM Delta OHM HD52.3D Series Manual de usuario

GHM

GHM GREISINGER Manual de usuario

GHM

GHM DeltaOHM LPPYRA-Lite Manual de usuario

GHM

GHM DeltaOHM HD52.3D Series Manual de usuario

GHM

GHM GREISINGER GTF 111-Ex Series Manual de usuario

GHM

GHM Delta OHM HD53LS Series Manual de usuario

GHM

GHM Delta OHM HD2114P.0 Manual de usuario

GHM

GHM DeltaOHM LPPHOT01 Manual de usuario

GHM

GHM Greisinger G 1409 Manual de usuario

GHM

GHM Delta OHM HD2105.1 Manual de usuario

GHM

GHM GREISINGER G 1000 Series Manual de usuario

GHM

GHM GREISINGER G 1500 Instrucciones de instalación

GHM

GHM Greisinger GMK 210 Cómo utilizar

GHM

GHM GREISINGER G 1111 Manual de usuario

GHM

GHM Delta OHM HD2106.1 Manual de usuario

GHM

GHM Martens BA 24N2 Series Manual de usuario

GHM

GHM Delta OHM LPPYRA11 Manual de usuario

GHM

GHM Delta OHM HD3405.2 Manual de usuario

GHM

GHM GREISINGER GIA 20 EB Documento técnico

GHM

GHM Martens TB225 Manual de usuario

GHM

GHM DeltaOHM LPUVA02 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario