Geutebruck GSD-200 Manual de usuario
MINISPEEDDOMECAMERA
MINI SPEED DOME CAMERA
UserMANUAL
GSD-200
TABLE OF CONTENTS
1. CATION ------------------------------------------------------- 3
2. INTRODUCTION OF PRODUCT -------------------------------5
1). DESCRIPTION AND FEATURES -----------------------------5
2). INSTALLING AND CONNECTING ---------------------------- 6
2-1. NAME AND FUNCTION OF EACH PART -------------------6
2-2. INSTALLATION --------------------------------------7
2-3. CONNECTION DIAGRAM --------------------------------8
3. DIRECTIONS FOR USE -----------------------------------------9
1). DIP SWITCH SETTING ---------------------------------------9
2). HOW TO CHANGE PROTOCOL -------------------------------10
3). HOW TO SET ADDRESS DIP SWITCHES ----------------------11
4). HOW TO USE OSD MENU ----------------------------------12
4-1. HOW TO CONTROL OSD MENU --------------------------12
4-2. FUNCTIONAL DESCRIPTIONS ON EACH MENU ------------13
4-3. SETTING FUNCTIONS BY KEYBOARD---------------------23
4-4. OSD MESSAGE DESCRIPTION ---------------------------27
4. TROUBLE SHOOTING ------------------------------------------29
5. DIMENSIONS & ASSEMBLES------------------------------------30
6. CONFIGURALTION ---------------------------------------------31
7. SPECIFICATIONS ----------------------------------------------33
1. CAUTION
Thank you for purchasing mini speed dome camera GMS-200.
Please operate the product after being fully aware of the manual.
Pease contact us if you have any queries or face any problems.
DO NOT CONTROL PAN, TILT BY FORCE
Do not move the inside Pan/Tilt motor by force
after removing dome cover.
It can cause damages.
HANDLE WITH CARE OF CAMERA LENS AND DOME
Be careful of handle with dome cover
Please use a soft fabric due to a scratch when you
clean the cover.
EXTERNAL SHOCK
Damages can be occurred through the carelessness
Or shock when you take out the module.
Dimensions
UNIT:mm
CAUTION IN USE.
Do not disassemble the unit and put alien substances in the unit.
It can cause troubles.
Ensure power switch-off before the installation.
Ensure power switch-off and check the voltage the camera before the installation.
Do not give the unit a shock and an operation.
Giving a strong shock or an excessive power on the button, terminal can cause troubles.
This product has been designed and manufactured in accordance with the harmonized European
standards, following the provisions of the below stated directives.
Electromagnetic Compatibility Directive 89/336/EEC(EN61000-3-2:1995, EN61000-3-3:1995,
EN50081-1:1992, EN50082-1:1997)
This devise complies with part 15 of the fcc rules operation is subject to the following two
conditions: (1) This device may not cause harmful interference and (2) This device must accept
any interference received including interference that may cause undesired operation
2. INSTRUCTION OF PRODUCT
1) DESCRIPTION AND FEATURES
- Description -
This camera has been designed elegantly for buildings, department stores that need to be
in harmony with the interior as a high speed dome camera, including various observation
functions. It moreover is effective for true Day & Night.
- Features -
High magnification zoom lens
Max 100 times zoom
(optical x10 zoom, digital x10 zoom)
Horizontal resolution min. 520 TVL
Color: min.520 TVL, B/W: min.570 TVL
horizontal resolution
Low light and Day & Night
The result of improving sensitivity
0.0007Lux (DSS Control)
ICR Day & Night allows the filter to change
B/W mode (0.1 Lux) in the night.
Additional functions
PTZ trace:
Memorize P/T/Z move for 120 seconds then
operate the registered trace.
Auto swing:
Repeat pan and tilt between two preset
positions.
Group:
12 Preset positions are chained in one Group.
(Max 12 Groups available)
Tour:
Max 12 Groups are bound.
410k Pixel CCD CAMERA
SONY CCD chip with high resolution and low
illumination condition.
250 Preset positions
A maximum of 250 preset positions can be
programmed. The preset function enables to set
where you want on monitor at any time.
4ch alarm inputs
It can be directly connected to sensor and used
with presets owing to built-in 4-channel
sensor input terminals.
It can be also operated together with other
equipment owing to built-in alarm output.
Auto Tilt move
The unit can track the object moving automatically
until 180° in vertical.
OSD (On Screen Display)
Provides character information displayed on the
monitor, such as the camera ID address,
camera name, preset number, sequence status,
and sets various functions of camera easily on
the OSD menu screen.
Privacy Zones
For the privacy, it can be programmed for
masking zone up to 4 locations on the
OSD menu screen.
Audio out (Option)
Built-in mono microphone without Amplifier.
2). INSTALLATION AND CONNECTION
2-1. NAME AND FUNCTION OF EACH PART
104 ¢ BUBBLE
CAMERA COVER
CAMERA BASE
P/T BASE
MAIN BASE
BOTTOM COVER
CAMERA BODY
CAMERA BODY COVER
2-2. INSTALLATION
Make 4 holes after attaching
ceiling guide where the
came
ra is set.
Take apart 4 bands of camera body
cover
Set up DIP switch
(Reference to XXP)
Connect with cables.
Tighten 4 screws. Attach the camera
body cover
Completion
Take out the cables
from the ceiling.
2-3. CONNECTION DIAGRAM
AC24V/500mA(GMS-200iS)
DC12V/1A (GMS-200S)
VIDEO IN AUDIO IN
CAMERA 1~128
DC JACK
RS-485 Sensor 1
4 ALARM INPUT
VIDEO INPUT Sensor 4
AUDIO
CAMERA 129
~CAMERA 255
Violet(N/O)
Gray(COM)
Black(GND)
Brown(CH1)
Red(CH2)
Yellow(CH3)
Green(CH4)
3.
DIRECTIONS
FOR USE
1) DIP SWITCH SETTING
Set the camera numbers in the state of
ADDR, set communication speed, protocol
in the state of INIT.
-This part is each address of camera.-
It shows the status of Power
On/Off. Green LED is On while
power is alive. In the status of
operation, red LED is off.
-TERMINALATION RESISTOR (DIP SW NO1)
~Turn the last camera on the data line as a
switch to turn on/off the terminal resistor on.
Turn the DIP SW of some of the farthest
cameras on in the case of the data lines
distributed to several directions.
* The first default is off.
-ADDRESS/ INITIAL SELECT (DIP SW NO3)
~Set ADDRESS DIP SW in the status of ADDRESS
(*Reference to next page*)
(.*** The first default is ADDRESS.**)
-Set the communication speed and Protocol
(Demand for the technical inquiry) up in the
state of the INITAIL.
-Select PAL / NTSC system.
-POWER ON/OFF (DIP SW NO4)
Set DIP SW only in the status of Power off.
Then turn on the power after setting DIP SW.
2) HOW TO CHANGE PROTOCOL
Set up this part.
The switch that selects Protocol. The switch that selects Baud Rate.
.
Change No.3 at S2 to INIT if want to change Protocol.
①Please make Power off.
②Switch Protocol that wants to change on as above table.
③Make Power on, then set Protocol and Baud rate are appealed.
④Make Power off, if every setting is right. Then it is done.
⑤Change No.3 of S2 to ADDR before Power on, then make Power on after setting the
address of the camera.
⑥Try it again with the information as above the table, if something is wrong.
Tabla de contenidos
Otros manuales de Cámara de seguridad de Geutebruck
Geutebruck
Geutebruck G-Cam/ESD-4510 Manual de usuario
Geutebruck
Geutebruck G-Cam/EBC-3141 Manual de usuario
Geutebruck
Geutebruck G-Cam/E2 Series Manual de usuario
Geutebruck
Geutebruck G-Cam/EWPC-4450 Manual de usuario
Geutebruck
Geutebruck EcoBC-1110 Manual de usuario
Geutebruck
Geutebruck G-Cam/EWPC-4270 Manual de usuario
Geutebruck
Geutebruck Guardian 704 ILB Manual de usuario
Geutebruck
Geutebruck GFD-632/VP-IR Manual de usuario
Geutebruck
Geutebruck G-Cam/ANPR-49 Series Manual de usuario
Geutebruck
Geutebruck G-Cam/EWPC-5240 Manual de usuario
Geutebruck
Geutebruck G-Cam/EWPC-3285 Manual de usuario
Geutebruck
Geutebruck XNet EcoFD-2410 Manual de usuario
Geutebruck
Geutebruck G-Cam EWPC-3210 Manual de usuario
Geutebruck
Geutebruck G-Cam/EBC-2112 Manual de usuario
Geutebruck
Geutebruck G-Cam/EFD-2251 Manual de usuario
Geutebruck
Geutebruck G-Cam/EFD-2251 Manual de usuario
Geutebruck
Geutebruck G-Cam/EBC-3310 Manual de usuario
Geutebruck
Geutebruck G-Cam/EFD-3245 Manual de usuario
Geutebruck
Geutebruck G-Cam/EWPC-5240 Manual de usuario
Geutebruck
Geutebruck G-Cam/ESD-3401 Manual de usuario
