German pool GPN-4SSL Manual de usuario
Please read these instructions and warranty information carefully
before use and keep them handy for future reference.
Online Warranty Registration
Rapid Fast Flow Electric Water Heater GPN-4SSL
USER MANUAL
GPN-4SSL
請即進行保用登記﹗
有關保用條款細則，請看本說明書最後一頁。
Please register your warranty information now!
For Warranty Terms & Conditions,
please refer to the last page of this user manual.
P.3
目錄 Table of Contents
警告事項 Warnings 04
產品特點 Features 05
產品結構 Product Structure 06
安裝說明 Installation Instructions 07
使用說明 Operating Instructions 09
安裝圖 Installation Diagram 11
電路圖 Wiring Diagram 12
專用節水花灑 Water Saving Shower Head 13
產品規格 Specications 14
保用條款 Warranty Terms & Conditions 15
P.4
警告事項 Warnings
警告
若用戶需要安裝任何非隨機配件，必須先與
本公司認可之技術人員聯絡，否則本公司將
有權拒絕提供任何保養服務。
Warning
Each unit is equipped with a standard open-outlet
mixer and a shower set. Please install water
heater in accordance to the instructions stated
on this booklet. German Pool will NOT provide
warranty service on any product installed with
unauthorized components or devices.
警告
1.必須嚴密看管兒童，防止他們接觸及把玩
熱水器，以免燙傷、觸電或受傷。
2.本產品不適用於缺少了身體、感覺或精神
能力，或缺乏經驗和知識的人（包括兒
童）使用，除非他們在一個了解本產品使
用的人監督指導下使用，並對他們的安全
負責任。
3.若設置溫度超過50°C，會有燙傷危險，所
以必須混合冷水後才使用。
4.電源進線段應加裝漏電保護裝置，漏電保
護裝置的額定動作電流應不大於30mA。
Warning
1. Do not allow children to touch or play with the
water heater. Supervision is required during
use, in order to prevent the danger of a scald,
electrical shock or any other injuries.
2. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
3.Ifthetemperatureissetabove50˚C,coldwater
must be mixed in to prevent the danger of a scald.
4. An electric-leakage protection device must be
installed to the power inlet. The electric current
of this protection device should be below 30mA.
! !
P.5
德國寶速熱式電熱水器(花灑型)配備原廠低壓
式混合水龍頭及花灑配件，適合於單點使用。
產品特點 Features
German Pool Rapid Fast Flow Electric Water Heater
(Shower Type) is a non-pressure water heaters
designed for single-point application.
不銹鋼內膽
Stainless Steel
Inner Tank
採用長期耐高溫及受高壓容器專用之日本特殊不銹鋼製造，內膽結構堅
固，保證防銹、耐壓及不受水質侵蝕。
Constructed of Japanese heavy gauge stainless steel, specially made for
high temperature and pressure applications. It is durable and free of rust,
corrosion, deformity and hassle.
保溫設計
Thermal Insulation
採用一體成型美耐棉，保持溫度，失溫程度達至最低，保持熱水溫度。
Maximum thermal insulation is achieved by high-density melafoam injection
moulded between the inner tank and outside casing.
額定壓力
Rated Pressure 0 MPa
最大來水壓力
Max. Inlet Water Pressure 0.6 MPa
發熱管
Heating Element
原廠優質不銹鋼發熱管，備有獨立不同功率，符合各種不同之熱水要求。
Prime quality stainless steel heating element ensures maximum thermal
efciencyeveninplaceswheredifferentpowerrating/wattageapplices.
溫度調節/超溫斷路器
CombinedThermostat/
Cutout
溫度調節/超溫斷路器自動恆溫，保持水溫在預調溫度，節省能源，超
溫自動斷路確保安全，並配合個人使用熱水的習慣。
CombinedThermostat/Cut-Outprovidesautomatictemperaturecontrolat
preset temperature to accommodate individual bathing habits and save
energy; built-in thermal cut-out ensures safety.
外殼
Exterior Casing
採用堅固防侵蝕金屬片。
Constructed of corrosion-proof metal.
防水等級
Water Resistance IPX4
符合規格
Conformity
機電工程署電氣產品（安全）條例。
Electrical Product (Safety) Regulation, Hong Kong.
認證標準
Certications
IEC 60335-2-21
IEC 60335-1
* 正常情況下，如供水系統之來水水壓超過0.6 MPa，用戶必須額外加裝減壓器將水壓調低。
如來水壓力超過0.6 MPa 而用戶未有安裝減壓器，本公司有權拒絕為熱水器進行任何維修。
* Under normal working conditions, incoming pressure should not exceed 0.6 MPa. Otherwise, a separate pressure control device is necessary.
When incoming water pressure exceeds 0.6 MPa, German Pool will not provide any repair service until a pressure control device is installed.
P.6
01
01
02
03
02
03
02 04 05
06
07
產品結構 Product Structure
發熱線(內部)
混合水制
溫度調節/超溫斷路器
1
2
3
GPN-4SSL
Heating Element (Inside)
Mixing Valve
CombinedThermostat/Cutout
1
2
3
P.7
安裝說明 Installation Instructions
安裝前注意
安裝必須使用原廠配件。若不按指示方法安
裝及使用而引致任何損壞，本公司概不負責。
安裝工作應由專業持牌水電技術人員負責。
Pre-Installation Notice
Installation should be done by a licensed
technician using the supplied parts. German Pool
is not responsible for any defect or damage
caused by incorrect or unauthorized installation.
Positioning
Positionwaterheaternearwatertap/pointofuse
in order to minimize heat loss. For wall-mount style,
appropriate anchor screws must be used and wall
should be strong enough to withstand the weight
of water heater. Keep a minimal distance between
wall and water heater.
Connecting Inlet and Outlet Pipes
Thediameterofpipingis½″BSP.Makesurethere
is no leaking at the joints. Turn on hot water tap
tolluptheinnertankuntilwaterflowsfromthe
shower head. Turn off hot water.
掛牆定位
先將熱水器背板以膨脹螺絲安裝於承重的牆壁
上，然後將熱水器背部凹孔扣在背板上，並調
整至緊貼牆壁及保持垂直為佳。花灑頭插座以
膨脹螺絲安裝於適當位置上。
水喉接駁
水喉管件直徑為1/2"英吋，接駁妥當後應試看
接駁位置有否漏水，妥當後即可將有紅點之熱
水掣打開注水，直至花灑頭噴水即表示內膽經
已注滿，並可將熱水掣關好。
! 特別注意 ! ATTENTION
P.8
安裝說明 Installation Instructions
發熱線功率 (千瓦)
Heating Element Rating (kW)
所需電源(安培)
Electric Current (A)
電源線最低要求(平方毫米)
Wiring (mm²)
3kW 15 A (單相1PE) 2.5 mm²
電源開關
設於熱水器外用以切斷電源供應之開關掣，應全
極切斷電源，兩極之間應保持最少3mm距離。
於浴室內安裝本電熱水器時必須遵照IEE之有關
電線安裝條例規格接駁。電源開關應採用有顯示
燈類型，當用戶需要作任何內膽清洗或維修，必
先切斷電源。
測試使用
水喉與電源接駁妥當及內膽注滿水後，便可進行
通電。此時指示燈會亮著，用戶便可將自動恆溫
旋鈕調校至最高度數。當溫度達到75℃時，恆溫
器即會自動停止加熱。選擇適當溫度後不應以恆
溫旋鈕當作開關掣使用，因此舉會縮減該配件之
使用壽命。
Power Switch
The external switch is used to completely disconnect
water heater from power supply. It should disconnect
all poles, and a contact separation of at least 3 mm
must be present.
IEE wiring regulations should be observed when the
water heater is installed in the bathroom.
Testing
Once the piping and wiring are connected and
inner tank has been filled up with water, switch
on the power. The indicator light will be lit. Turn
control knob to the desired temperature (Max.
temperature is 75°C). Do not use the control
knobasanon/offswitch.
接電方法
由電箱獨立伸延一條適合之電線(見下表)至浴室
門外接駁獨立開關掣，再將電線伸延至熱水器
穿進灰色線夾接到電線排上分別接上零線(N)，
火線(L)，及地線( )等。
Electric Wiring
Use an independent wire (refer to table below)
leading from the meter box and connect it to an
independenton/offswitchoutsidebathroom.
Extend the wire through the grey wire grip on the
water heater. Dismount the bottom plate and wire
up Neutral (N), Life (L) and Earth ( ) terminals.
! 特別注意 ! ATTENTION
本熱水器必須永久可靠地連接地線。 This water heater must be earthed at
all time.
P.9
使用說明 Operating Instructions
!!
重要注意事項 WARNING!
儲水式電熱水器安裝並進行通水通
電測試後，如果不是繼續使用，而
是先擱置一段時間後再使用，測試
完畢必需進行以下程序：
1. 將電熱水器斷電斷水；
2. 將電熱水器內測試的水排清；
3. 當存放後需要正常使用前，必需將電熱水
器注滿水並確定滿水後，才可以通電加
熱，進入正常使用。
After initial installation and water
and electricity testings, if the storage
water heater will not be put to use
immediately, after testing is completed,
make sure to follow these instructions:
1. Disconnect water and power source to
the water heater;
2. Completely drain the residual water in
the water heater;
3. Whenthewaterheaterisnallyputto
normaluse,userMUSTrstcompletely
llupthewaterheaterwithwater
BEFOREreconnectingthepowersource
and commencing heating.
注意：
對於水源是地下水以及（有可能海水倒灌的）河水地區的使用者，必需嚴格遵照上列程序，
以確保熱水器正常運作。
NOTE:
If water source is from underground water or near river area where seawater intrusion is
possible, user MUST COMPLY with all of the above steps to ensure proper function of water
heater.
!!
安裝注意事項 INSTALLATION REQUIREMENT
ATTENTION: When installing the water
heater, must leave ample space for
future maintenance and repair.
The minimum requirements are:
1. at least 100 mm space from the
ceiling
2. at least 200 mm on either side of
the wall
3. at least 300 mm underneath the
heater
注意：安裝熱水器時必須預留足夠空間作
日後保養和維修之用。
最少預留空間：
1. 距離天花最少100毫米
2. 距離兩邊牆壁最少200毫米
3. 爐底預留最少300毫米
P.10
使用說明 Operating Instructions
停水期間
停水時不應將熱水器內之存水用盡，否則會導
致發熱線損壞。恢復供水後，應先扭開熱水掣
直至有水從花灑流出。待內膽注滿水後，用戶
便可重新開啟電源。
水質問題
若來水水源為河水、井水、地下水或礦物質含
量較高，用戶必需經常定期清洗發熱線以確保
發熱線正常運作及發揮最佳製熱效能。
花灑頭滴水
因冷縮熱脹原理，熱水器內膽當達到高溫時便
會有少量水在花灑頭流出。
出水位
出水位乃本熱水器之排氣管，除德國寶指定之
花灑配件外，不得接駁任何其他水喉配件或
裝置。
Water Shortage
During water shortage, do not drain water from in-
ner tank. The heating element would be damaged if
it is not submerged under water. When water supply
resumes,turnonhotwatertapandletwaterflows
through the shower head before switching on the
power.
Source of Water Supply
If the water source is a river, a well, underground
water or has relatively high mineral content, user
must clean the heating element regularly to ensure
itwilloperateatoptimumthermalefciency.
Dripping
Due to thermal expansion, small amount of water
may drip off from the shower head when the inner
tank temperature is very high.
Outlet
The outlet of the water heater is supposed to act as
a vent and should not be connected to any unau-
thorized piping attachment or device.
Tabla de contenidos
Otros manuales de Calentador de agua de German pool
German pool
German pool GPI-M5 Manual de usuario
German pool
German pool cex9 Manual de usuario
German pool
German pool GPUB-6SSL Manual de usuario
German pool
German pool CEX21 ELECTRONIC MPS Manual de usuario
German pool
German pool GPU-6SSL Manual de usuario
German pool
German pool GPN Series Manual de usuario
German pool
German pool GPI-M8 Manual de usuario
German pool
German pool GPI-M6 Manual de usuario
German pool
German pool DEX Manual de usuario
German pool
German pool GPI-M5 Manual de usuario
German pool
German pool GPS12 Manual de usuario
German pool
German pool DBX Manual de usuario
German pool
German pool GPS13 Series Manual de usuario
German pool
German pool GPU-6SSM Manual de usuario
German pool
German pool GPU Series Manual de usuario
German pool
German pool GPNB Series Manual de usuario
German pool
German pool GPN Manual de usuario
German pool
German pool GPI-M6 Manual de usuario
German pool
German pool DB Manual de usuario
German pool
German pool GPU Series Manual de usuario
