GeoVision GV Series Manual

Hardware Installation Guide

GV-Fisheye IP Dome

GV-FE2302 / 3402 / 5302 / 3403 / 5303

GV-FER3402 / 5302 / 3403 / 5303

Thank you for purchasing GV-Fisheye IP Camera. For advanced information on

how to use the GV-Fisheye IP Camera, please refer to GV-Fisheye IP Camera

User's Manual and Quick Start Guide online.

2015/04

English

FEV3-QG-C

61-MEFERV3-Q001

Important

Note for Connecting to GV-System / GV-VMS

The GV-Fisheye IP Camera is designed to work with GV-System / GV-VMS,

a video management system. Note the following when the camera is

connected to GV-System / GV-VMS:

1. By default, the images are recorded to the memory card inserted in the

GV-Fisheye IP Camera.

2. Once the camera is connected to GV-System / GV-VMS, the resolution

set on GV-System / GV-VMS will override the resolution set on the

camera’s Web interface. You can only change the resolution settings

through the Web interface when the connection to GV-System / GV-VMS

is interrupted.

Note for Recording

1. By default, the images are recorded to the memory card inserted in the

GV-Fisheye IP Camera. Make sure the Write recording data into local

storage option is enabled. If this option is disabled, the camera will stop

recording to the memory card while the live view is accessed through

Web browsers or other applications. For details, see Video Settings,

Administrator Chapter, GV-Fisheye IP Camera User’s Manual online.

2. Mind the following when using a memory card for recording:

●Recorded data on the memory card can be damaged or lost if the

data are accessed while the camera is under physical shock, power

interruption, memory card detachment or when the memory card

reaches the end of its lifespan. No guarantee is provided for such

causes.

●To avoid power outage, it is highly suggested to apply a battery

backup (UPS).

●For better performance, it is highly suggested to use Micro SD card of

MLC NAND flash, Class 10.

●Replace the memory card when its read/write speed is lower than 6

MB/s or when the memory card is frequently undetected by the

camera.

Mind the following limitations and requirements for using USB storage and

GV-WiFi Adapter:

When installing GV-FER outdoor models, be sure that:

Note for USB Storage and WiFi Adapter

3. It is recommended to use memory cards of the following setting and

specifications:

1. The USB hard drive must be of 2.5” or 3.5”, version 2.0 or above.

2. The USB hard drive’s storage capacity must not exceed 2 TB.

3. USB flash drives and USB hubs are not supported.

4. External power supply is required for the USB hard drive.

5. To connect a GV-WiFi Adapter, make sure it is connected before the

camera is powered on.

IR LED Ring

●Apply a battery backup (UPS) to avoid power outage.

●Use Micro SD card of MLC NAND flash, Class 10 for better

performance.

Note for Installing Camera Outdoor

1. The camera is set up above the junction box to prevent water from

entering the camera along the cables.

2. Any PoE, power, audio and I/O cables are waterproofed using waterproof

silicon rubber or the like.

3. The screws are tightened and the cover is in place after opening the

camera cover.

4. An operating IR LED ring may reach high temperatures of up to 60°C

(140°F). Disconnect the power supply and allow the IR LED ring to cool

down before handling the device.

5. The silica gel bag loses it effectiveness when the dry camera is opened.

To prevent the lens from fogging up, use the supplied adhesive tap and

replace the silica gel bag every time you open the camera, and conceal

the gel bag in camera within 2 minutes of exposing to open air.

GV-FER3402 / 5302 and GV-FER3403 / 5303

Packing List

Camera Cover

(Hard Ceiling Mount)

Camera Cover

(In-Ceiling Mount)

IR LED Ring

(GV-FER3403 / 5303)

Fisheye Camera

Support Bracket x 3 Plastic Screw Anchor x 3 Screw x 3

(Hard Ceiling Mount)

Screw x 3

(In-Ceiling Mount) Torx Wrench

Installation Sticker IR Power Adapter

(DC 12V, 3.5A,

GV-FER3403 / 5303)

Power Adapter

(DC 12V, 1.25A)

Note: The power adapter

(DC 12V, 1.25A) can be

excluded upon request.

Power Cable Waterproof Rubber Terminal Block x 2

Device

TOP

Device

PoE Converter

(female) (male)

●GV-Fisheye IP Dome Hardware Installation Guide

●GV-NVR Software DVD

●GV-NVR Quick Start Guide

●Cable Connector

●Silica Gel Bag and Adhesive Tape x 2

●GV-IPCAM H.264 Software DVD

Overview Connecting the Camera

Speaker

Microphone

Lens

Default Button

Micro SD Card Slot

LEDs

Power Terminal

Block

Rubber Seal Ring

A. Prepare a network cable with the RJ-45 connector on one end only.

B. Connect the network cable to the camera data cable.

C. Slide in the components through the end of the network cable without

RJ-45 connector as shown below.

D. Move the components toward the RJ-45

connector, secure item 1 to the Rubber Seal

Ring of the camera data cable and secure item

2 to item 1 tightly.

1 2

1. Remove the camera cover with the supplied torx wrench.

2. Connect the camera to a Power over Ethernet (PoE) switch with a

standard network cable to supply power and network.

To waterproof the cable, you should have 2 components of the supplied

cable connector:

Installation

Waterproof Rubber

Power Cable

IMPORTANT: Item 1 must be secured tightly to waterproof the

cable.

Without IR LED Ring With IR LED Ring

To install GV-Fisheye Camera with the IR LED ring (GV-FER3403 /

5303), drill the 3 holes indicated as “Device” and the circle

indicated as “IR”.

Hard Ceiling Mount

Device

TOP

Device

PoE Converter

Place the installation sticker on the ceiling board. The 3 red dots

indicate the location of the screws.

2. Insert the power cable into the supplied female terminal block as

illustrated and plug it into the terminal block connector in the camera.

3. Connect the male terminal block on the power cable to female terminal

block on the power adapter as illustrated below.

DC 12V

Power Adaptor

Terminal Block

Female Terminal Block

(Connect to Camera)

FemaleMale

Assembling the Power Adapter

3. Optionally insert a micro SD card (SD/SDHC, version 2.0 only, Class 10).

4. Secure the camera cover with the supplied torx wrench.

1. Insert the supplied power cable into the supplied waterproof rubber.

In addition to using PoE power supply, you can use the power adapter to

supply the power to the camera.

At the 3 red dots, drill a hole slightly smaller than the plastic screw

anchors provided.

3For the camera with an IR LED ring, follow the steps below to

secure the IR LED ring to the camera.

Insert the 3 plastic screw anchors in the drilled holes.

Secure the camera with the 3 hard ceiling mount screws provided.

For the camera that does not come with an IR LED ring, place the

camera cover (for hard ceiling mount) on top of the camera and

tighten the screws with the supplied torx wrench.

Continued on the reverse

A. Secure the safety lock to the camera. Then secure the

camera cover.

B. Place the IR LED ring on top of the camera and tighten

the screws with the torx wrench provided.

Align the 3 support brackets with the notches on the side of the

camera and secure on the back with the in-ceiling mount screws

provided.

Place the fisheye camera into the ceiling opening.

Place the installation sticker on the ceiling board, and cut the circle

part out of the ceiling. Drill the 3 holes indicated as “Device”.

In-Ceiling Mount allows the GV-Fisheye IP Camera to be mounted into the

ceiling, revealing a small portion of the camera. In-Ceiling Mount requires

the ceiling board to be between 0.5 – 3.0 cm (0.2 – 1.18 in).

In-Ceiling Mount

Note: In-ceiling mount is not applicable to the models with IR LED

ring (GV-FER3403 / 5303).

Device

TOP

Device

PoE Converter

On the back side, make sure the black plastic clips are slightly

above the ceiling board and pointing outward.

From the front side of the camera, tighten the screws.

Place the camera cover for in-ceiling mount on top of the camera

and put on the in-ceiling cover.

GV-FE2302 / 3402 / 5302 and GV-FE3403 / 5303

Packing List

Camera Cover

(Hard Ceiling Mount)

Camera Cover

(In-Ceiling Mount)

IR LED Ring

(GV-FE3403 / 5303)

Fisheye Camera

PoE Converter set

(including 1 module, 1 DC Power Y-cable, 1 RJ-45 cable and 3 screws)

(GV-FE3403 / 5303 only)

Support Bracket x 3 Plastic Screw Anchor x 3

Screw x 3

(Hard Ceiling Mount)

Screw x 3

(In-Ceiling Mount) Torx Wrench

Installation Sticker Mini USB Extension Cable

Device

TOP

Device

PoE Converter

Speaker

Microphone

Lens

Rubber Bung

Default Button

Status LED

Micro SD Card Slot

Mini USB Slot

Audio Out

LAN / PoE

Power Terminal

Block

Overview

●GV-IPCAM H.264 Software DVD

●GV-Fisheye IP Dome Hardware Installation Guide

●GV-NVR Software DVD

●GV-NVR Quick Start Guide

Note: The power adapter can be excluded upon request.

Connecting the Camera

1. Remove the camera cover with the supplied torx wrench.

2. Supply power and network to the camera with one of the following

methods:

3. Optionally insert a micro SD card (SD/SDHC, version 2.0 only, Class 10).

4. Optionally connect an external speaker.

5. Optionally connect a GV-WiFi Adapter (for WiFi accessibility) or an

external USB hard drive (for additional storage).

6. Secure the camera cover with the supplied torx wrench.

A. Power over Ethernet (PoE): connect the camera to a PoE switch

with a standard network cable to supply power and network.

B. PoE Converter: only for indoor cameras GV-FE3403 / 5303 installed

with an IR LED ring. A PoE converter allows the camera to be

connected to a PoE switch,and also supplies power to IR LED ring.

For installation steps, see the next section Connecting PoE Converter

and IR LED Ring for GV-FE3403 / 5303.

To install a PoE converter, follow the steps below.

Note: Instead of installing the PoE converter, you can connect the

camera to a PoE switch and the IR LED ring with a power adapter

(optional accessory) separately.

PoE Converter

PoE Switch

1. Connect the PoE converter to a PoE switch with a standard network

cable. Use the RJ-45 connector on the left.

2. Connect PoE Converter and the camera with the supplied network cable.

Use the RJ-45 connector on the right.

Connecting PoE Converter and IR LED Ring for GV-FE3403 /

5303

E Conver

oE converter to a PoE switch with a

Camera

IR LED Ring

Note:

1. Due to limited space inside the PoE converter, use a standard

network cable without the rubber boot.

2. The camera will not work if you connect the wrong devices to

the two RJ-45 connectors on the PoE converter.

Otros manuales para GV Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de GeoVision

GeoVision

GeoVision GV-ABL Series Manual de usuario

GeoVision

GeoVision GV-TBL Series Manual de usuario

GeoVision

GeoVision GV-EDR2700 Series Manual de usuario

GeoVision

GeoVision GV-EBD4700 Manual de usuario

GeoVision

GeoVision GV-3D People Counter V2 Manual de usuario

GeoVision

GeoVision 84-VD870000-001U Manual de usuario

GeoVision

GeoVision GV-BX110D Manual de usuario

GeoVision

GeoVision GV-SD220 Series Manual de usuario

GeoVision

GeoVision PPTZV10-QG-A Manual de usuario

GeoVision

GeoVision GV-BL8714 Manual de usuario

GeoVision

GeoVision GV-VD120D Manual de usuario

GeoVision

GeoVision GV-GEBF4911 Manual de usuario

GeoVision

GeoVision GV-FEC5302 Manual de usuario

GeoVision

GeoVision GV-SD2322-IR Manual de usuario

GeoVision

GeoVision GV-LPR2811-DL Manual de usuario

GeoVision

GeoVision GV-EFER3700 Series Manual de usuario

GeoVision

GeoVision GV-GDR4900 Manual de usuario

GeoVision

GeoVision GV-IPCam H.264 Series Manual de usuario

GeoVision

GeoVision GV-IP LPR-DL Manual de usuario

GeoVision

GeoVision GV-MFD1501 Manual de usuario

GeoVision

GeoVision GV-PTZ010D Manual de usuario

GeoVision

GeoVision GV-VD8700 Manual de usuario

GeoVision

GeoVision 86-PPTZ730-P01U Manual de usuario

GeoVision

GeoVision GV-VR360 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario