GeoSIG GMS plus Guía de instalación

FAQ GMSplus How to Use as NTP Client ¶

1. Introduction

This procedure describes how to set a GMSplus as NTP client.

It will allow the GMSplus to synchronize its time with a NTP server.

2. Required Tools

GMSplus with network connection

Domain or IP address of a NTP server.

It can be a public server (see e.g. pool.ntp.org), a dedicated server in your network (check with your network admin) or a

GMSplus with a GPS configured as NTP server (http://www.geosig.com/files/FAQ_GMSplus_How_to_Use_as_NTP_Server.pdf)

3. Enter NTP server in GMSplus config

The NTP server can either be entered through the webinterface (3.1) or from GMSplus serial console (3.2)

3.1 Enter NTP Server through Webinterface

Open your webbrowser, enter the IP address of your GMSplus and login as admin (default password 123456)

Choose tab Configuration and click Miscellaneous Parameters

Click Time synchronization

Choose Time source NTP from the dropdown

Enter the IP or domain of your primary NTP server

Enter the IP or domain of your secondary NTP server (enter the primary NTP server again if you don't have a secondary)

Click Apply and Restart and confirm the pop-up with Yes to apply the changes

3.2 Enter NTP Server from GMSplus Serial Console

Connect to the serial console of your GMSplus

Press C to enter the configuration menu and press C again to edit current configuration

Press O to enter Miscellaneous Parameters

Press K to enter Time synchronization

Press A until Time source shows NTP

Press I to enter the IP or domain of your primary NTP server

Press J to enter the IP or domain of your secondary NTP server (enter the primary NTP server again if you don't have a

secondary)

Press Esc followed by ENTER and again Esc followed by ENTER to get back to the main menu

Press Esc to exit the menu

Press C to save the configuration as "current"

In the main menu, press R followed by Enter to restart the instrument

After the restart, the configuration changes are applied

Make sure that SOH status of the time sync shows Locked (can take several minutes)

Otros manuales para GMS plus

Otros manuales de Instrumento de medición de GeoSIG

GeoSIG

GeoSIG GMS-scai Guía de instalación

GeoSIG

GeoSIG AC-73-DH Instrucciones de instalación y funcionamiento

GeoSIG

GeoSIG GSR Series Manual del propietario

GeoSIG

GeoSIG GMS plus Manual de usuario

GeoSIG

GeoSIG AC-23 Manual de usuario

GeoSIG

GeoSIG GMS plus Manual del propietario

GeoSIG

GeoSIG AC-23 Manual de usuario

GeoSIG

GeoSIG AC-73 Manual de usuario

GeoSIG

GeoSIG GMS-GPS Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario