GEO-Laser UL-89L Manual de usuario

Algebraic sign

Status symbols

= Initialising

Inclination adjustment

Inclination adjustment finished,

power saving mode

T = Kick guard active (see 3.3)

T = Blinks after jerky movement,

laser beam off

Power supply indicator

Laser beam symbols:

Laser blinks when levelling

Laser off when levelling

Laser + rotor off with FB-10

Percent sign (see 3.5)

Inclination value, x/y axis resp. OFF

Rotor speed (8 = 800 rpm)

< 1/4 < 1/2 < 3/4 >3/4

Keep the button pressed until the adjustment menu is shown.

factory defaults

actory defaults

on. When setting the inclination, + or - can be selected and

then inverted.

= off (factory default)

Please note: Setting only possible in a range of ± 5 %.

3.10 Laser Power

The laser power can be regulated in 5 steps from approx. 0.5 mW

to < 2.6 mW.

Up to a range of approx. 200 m step 2 = < 1 mW is recommended.

= < 2.6 mW ( )

3.11 Operation Mode Laser Beam

Laser beam and laser beam symbol at the operating mode

=display blink when levelling ( ).

= Laser beam is off when levelling.

However the symbol blinks at the operating mode display.

3.12 F

= All set to factory defaults.

3.13 Service/Workshop Notice

First off all a phone no. for service/help appears. Then authorized

personnel can put in a numerical code to come to the adjustment

mode.

Select Letter

The selected letter blinks.

Change Settings

Back to Operating Display

= Select Indication of Factory Defaults

6. Locking Automatic (see 19.)

in the Y axis in combination with the locking receiver FE-53. Laser and receiver

correspond via radio circuit.

By pressing the button of laser or receiver the laser startsto search for the receiver.

As soon as the rotating laser beam hits the receiver,it is directed to the center and

fixed there.

6.1 Operation

Set-up laser and receiver over the line axis, switch on

both, switch off Y axis and set the rotor speed to 800

rpm. As soon as the radio control is connected, the

system startsto operate.

On the laser display an alternating direction arrow

appears and on the receiver the LEDs are blinking

alternately.

Accuracy: to +/- 0.5 mm/100 m.

The FE-53 can be mounted either on the left or on the right side of the laser.

Because of reasons of functionality,the keyboards of both devices must be on the

same side.

Scan mode

Radio control:

connected

connected and laser reception

disconnected

Direction arrow

Centre indicator

Rotor speed 8= 800 rpm

6.2 Display Locking Automatic (Horizontal Set-Up)

6.3 Scan Mode

It can be started either at receiver or at laser.After its activation the laser scans and

finds the receiver automatically.

Start scan at laser:

3 x =

or =Scan starts.

The indicates the control direction on the display.

Sblinks

Note: A radio communication with the FE-53 is provided, indicated by the

symbol " " on the LCD display (see 1.9).

8.1 Horizontal Light Plane ( )

Adjustment Checking

Set-up the laser upright and mark laser beam in the height of the required

measuring distance. Turn laser device on the tripod by 180°, mark once again. If

the adjustment is perfect, the first mark does not deviate from the second one. Turn

device by 90°, repeat this process.

VerticalSet-Up

8.2 Horizontal Plumb Beam ( /Pipe Laying)Horizontal Set-Up

8.3Adjustment

If the adjustment is incorrect, please contact your specialist dealer.

The laser can be adjusted in the field without having to open the device. For safety

reasons, however, adjustment should only be carried out by authorized

personnel. See the special adjustment instructions in this regard.

Pressing the arrow buttons briefly changes the inclination value by 0.001 %.

The value is changed with increasing speed if the button is kept pressed.

+= 2.4 X Inclination Setting to Zero

The inclination value is set to 0.000 % by pressing the two arrow buttons at

the same time.

Y Inclination Setting

(Verticalset-up)

or Direction Setting

(Horizontal set-up)

Y Inclination Setting to Zero or

Direction Centering

+= 2.7

Verticalset-up:

Horizontal set-up: Device is automatically centred in middle position.

The inclination value is set to 0.000 % by pressing the

arrow buttons at the same time.

2.8 Quick Setting

In addition to the respective arrow button also press the ON/OFF button.

After setting one of the two arrow buttons the laser beam symbol changes to an

arrow. It indicates the direction of movement and the current position. When end

position is reached, the laser beam and limitation symbol blink. The setting must

then be moved back within 2.5 minutes. If this is not done, the laser is switched off

automatically.

Grade swap: minus or plus

(to activate see 3.9)

3. Device Settings

= 2.6

= 2.9

3.1 Switch ON/OFF Automatic Levelling

These are the factory defaults. They are always activated when

switching-on the laser.

= utomatic self-levelling cutted out in X and Y axis.

= utomatic self-levelling swiched on in X axis.

These are the factory defaults. They are always activated when

switching-on the laser.

= Automatic self-levelling swiched off.

On the display appears OFF %.

= Settings unlocked (

= Inclination and direction setting locked.

Now direction control is not possible.

Vertical Set-Up

Horizontal Set-Up

3.2 Sensitivity Setting (Wind/Vibration)

The self-levelling function corrects even the smallest deviation.

Additionally the laser beam and the laser beam symbol at the operating

mode display blink when the limit values of step 1 to 3 are exceeded,

i. e. by influence of wind and/or vibration.

1 = 0.005 % no effect

2 = 0.010 % weak effect( )

3 = 0.015 % stronger effect

3.3 Kick Guard (Automatic Laser Beam Cut-Out)

= Kickguard switched on. It is only active after 30 sec. Then a T appears

in front of the battery symbol at the operating mode display

This means the laser is switched offautomatically as a precautionary

measure in the event of a jerky movement (bump). The Tthen begins to

blink. The laser must be switched on again by pressing briefly the ON-

button and the positioning must be checked and corrected if necessary.

= F : Kick guard switched off.

3.4 Inclination value display in % or ‰

Select between % or ‰ indicator.

)

nclination setting locked.

Automatic levelling switched on.

On the display appears behind the Xand YOFF.

Now the X and Y axes can be selected and set by the arrow buttons.

factory defaults

actory defaults

When the automatic is switched off in X and Y axes, it is not possible to

activate the kick guard.

factory defaults

3.5 Lock Function only when Setting-up Horizontally

factory defaults .

3.6

3.9

Radio Control On/Off

Is required for the operation with the remote control FB-10 or locking

receiver FE-53/-61.

off (energy-saving mode)

on ( )

3.7 Laser Beam Modulation Mode

= Standard modulation for FE-61 ( )

=db

= Modulation off

= Flickering for LE-7x stationary beam

3.8 Monitoring of Locking Automatic

When using the locking receivers FE-53/-61 the automatic locking can be

monitored. The laser beam switches off when the laser or radio

contact is interruped for more than 3 min.

It can be switched on again by briefly pressing the laser ON button.

= off ( )

=on

factory defaults

Grade swap

It is possible to transfer the inclination i. e. of a roof profile from

one side to the other.

7. Inclination Measurement Parallel to Ground

Even if the inclination is unknown, it can simply be adapted to the ground.

9 - 21 10 - 21

8 - 21 11 - 21 12 - 21

7 - 21

Automatik-Kanalbau-Laser

KL-80/-81

= 2.1 ON/OFF Button

The device is switched on by pressing this button. The device and company data

are then shown, followed by the operating display with the last settings without

button lock. The device is then levelled and referenced on the zero point

automatically.After the levelling phase the laser beam and laser beam symbol stop

blinking. If this does not happen, the device must be moved into the levelling range

by tilting it forwards. The display illumination switches off after approx. 30 seconds

automatically. The illumination is switched on again by pressing the ON/OFF

button shortly.

To switch off the device, press the ON/OFF button until “Auf Wiedersehen !”

appears.

= 2.2

When setting-up vertically,the X inclination setting, the y inclination setting and the

rotor setting, when setting-up horizontally the lock symbol and the rotor speed are

selected and released one after the other by pressing the MENU/OK button.

The respectively activated point blinks.

If, after setting the speed, the button is pressed again or a time of about 25

seconds passes, the adjustment guard is reactivated automatically. This means:

the arrow buttons do not work.

Lock-, Rotor Speed- and X Inclination

Setting

or = 2.3

Arrow Buttons - Release

Select - Set - Confirm

Date 12/2015 Subjct to change

4 - 21 5 - 21 6 - 21

1.8 Bubble Tube (Set-up help).

Universal-Laser UL-89L

FE 53

FB-10

L -72E

one for all . .

FE-61

= 2.5

Check or Change Device Settings

or automatically after 25 seconds.

laser beam

FE-53

Y axis

Horizontal- Set-Up

2. Buttons

1.15 Antenna Remote Control (see 21.)

1. Description

1.1 Function

The automatic universal laser UL-89L is a multifunction laser with

inclination setting for horizontal and vertical use capable of

electronic self-levelling over three axes. It emits a laser

beam, which turns into a light plane as it rotates.

Another laser beam is available exactly square to it.

The operation is made at the laser or optionally with the

wireless control FB-10. The rotating laser beam in the Y axis is locked

by the locking receiver FE-53 and the plumb beam in the Y and X axes

by the FE-61.

1.7 Bulging

GroundArea, niro St.

Protects against damages of

coat and guarantees a secure

stand.

Central fastening thread 5/8“. Identification

mPlumb-Bea

Plumb-Up-Beam

1.12 Rotor Head

Rotor speed adjustable from 200 - 1000 rpm.

1.14 Handle

For easy handling, safe transport and simple set-up.

1.2 Inclination Symbol

Enables clear inclination assignment.

The +/- and X/Y symbols indicate the inclination. The + ranges are

light and the - ranges dark.

The symbol also shows the inclination and its change relative to

the centre axis.

1.6 Laser Warning Sign

Laser class 3R, P < 5 mW

1.4 Keyboard

Clear layout. User-friendly, self-explanatory keys.

1.5 Robust Light Metal Housing

Plastic-coated, swept with nitrogen, 100 % watertight.

1.3 Charging Socket

Behind the dust guard cap.

1.10 Optical sight

for quick alignment of the inclination axis.

1.13 Manual Rotor Setting

Pressed in: rotor motor cut out

Extracted: rotor motor cut in again

By turning: setting of the desired position

1.11 Box Level in rotor head for plumb-down function.

Fixing Foot

Sliding

Foot

Horizontal Set-Up

Vertical Set-Up

Operating Instructions

Congratulations on your new GEO laser

This operating instructions contain enclosed in addition to

information on how to use the laser important safety

information.

First read the safety instructions on the

supplement page and then the operating

instructions carefully before using the laser.

Please note:

1 - 3

Uncompromising versatility

+ much more

Two-Axis Inclination Laser

Levelling Laser

Aligning Laser

Plumb Laser

automatically

lock alignment

find alignment

search for alignment

1.9 LCD-Display, Horizontal Set-up (Pipe Laying)

Lock symbol open / closed

Algebraic sign

Inclination value

Percent sign

Status symbols:

Initialising

Inclination adjustment

Inclination adjustment finished,

power saving mode

T = Kick guard active (see 3.3)

T = Blinks after jerky movement,

laser beam off

Power supply indicator

Scan locking automatic

Radio control with FE-53/-61/FB-10:

connected

connected and laser reception

disconnected

Direction limitation

Centring indicator

Direction arrow

Centre indicator

Laser beam symbol

Laser beam and rotor off by remote

control

Rotor speed (8 = 800 rpm)

< 1/4 < 1/2 < 3/4 >3/4

1.16 LCD-Display, Vertical Set-up (Surface Construction)

V= Lock

Automatic cut out

Sensivity

Kick guard

Percent / Per mil

Radio control

Laser beam modulation

Direction automatic

Grade swap

Laser power

Duty type - laser beam

Factory defaults

Service/workshop information

Factory defaults

on/off

Laser blinks when levelling

Laser off when levelling

off/on

off/on monitored

S= standard for FE-61

P=db

-=off

F= Flicker for LE-7x standing

on/off laser beam

off/on

on/off

1 - 5 :

I= X axis

+= X axis + Y axis

%or ‰

1 - 3 = approx. 5 - 15 mm/100m

1 - 2 = 2

3 - 5 = 3R

Laser class

Display Device Settings

1 2 3

4 56 78 910 11 12 13

Although the laser is adjusted precisely by the manufacturer, jolts and strong

vibrations can lead to maladjustment. The laser should therefore be checked

before use:

1. Select a measuring area of approx. 40 m that is as horizontal as possible and

set up the laser with the counter at 0.000%.

2. Set up two control points, one directly in front of the laser and the other in a

distance of approx. 40 m, and measure the distanceto the centre of the laser

beam "a" and "b".

3. Set up the laser behind the second measuring point and repeat the measuring

process in reverse direction, this means measure "A" and "B".

4. If the adjustment is correct, A - a = B - b. This means, the laser beam of the first

installation is parallelto the second one.

Error-free: A - a = B - b

1st build A

40 m

2nd build

5.3 Height Transfer

5.2 Axis Transfer by Bearing over the Plumb Line

5.1 Axis Transfer with the Alignment Line

5. Transfer Possibilities

Alignment line

2nd plumb

Aim point

Datum

1st plumb

Aim point

plumb line

1. Set up laser over the axis.

2. Look over the plumb line and align it to the alignment rod.

3. Look over the plumb line to the laser beam and align the laser in the

direction.

Measuring rod

Height point

Level device

65 A

Rod reading A

- Rod reading B

+ 65 mm

+ 1/2

-----------------------

= Pipe invert

4. Pipe Laying Made Easy

Mount device over the point of reference in such a way that the bubble tube is

levelled in. Adjust the inclination and align the laser beam to the point of aim.After

that join pipe after pipe and align each end to the target.

4.1. Set-up

The laser can be set up centrically or at a constant distance above the pipe

invert. Suitable legs, tripods and fastening systems are available for this.

Note: If the diameter indicated on the legs does not correspond with the pipe

diameter, the target has to be set up directly in front of the laser and must

be adjusted to the correct height ignoring the diameter marking.

Laser

Construction

Height

Reference

Point

Xnln in

Icia

o Ais

Aiming Point

Laser

Construction

Height

Scanning locking receiver

Direction arrow

alternately OFF resp.

inclination value

Radio control:

connected

connected and laser reception

disconnected

7.1. Operating Instructions

Mount laser above the reference point and align the Y inclination axis to the

aiming point. Adjust banking in the X axis.

Measure laser construction height with the locking receiver FE-53 and a

levelling rod. Transfer this height to the aiming point.

Release the automatic scan with the A button of the receiver.

The light plane is now automatically directed within typically 2 min./max. 5 min.

to the centre of the receiver and locked there.

The LEDs at the FE-53 are blinking alternately. On the display OFF and the

approx. inclination value are shown alternately.

Now the FE-53 can be removed abruptly off the laser light plane and switched

off. After approx. 30 seconds the exact inclination value is shown on the

display and automatically locked. The % symbol is blinking.

Alternatively the FE-53 can be mounted permanently to realize a long-term

fixing of the laser light plane.

Please note: Never operate the remote control or inclination setting at the

laser in this mode because by this the laser light plane is moved.

Precondition is an established radio link to the FE-53, indicated

by the symbol on the LCD display.

7.2 Display Inclination Measurement (Vertical Laser Set-up)

14 - 21 15 - 21 16 - 21 17 - 21 1 8 - 21 19 - 2 1 21 - 21

Target from DN 500, suitable on and in

the pipe, upright and suspended

09 0017.04.1 KL-05

20 - 21

Table of Contents Page

Safety Information. . . . . 1 - 2

Laser Safety . . . . . . . . 2 - 3

Repair.............3

EMC.............3

Guarantee ..........3

Disposal............3

1. Description . . . . . . . . 5 - 6

2. Buttons 6 - 7

3. Device Settings . . . . . 7 - 9

4. ... 10

5. ....10

6. Locking . . . . . . 11

7. Inclination Measurement 11 - 12

..........

Pipe Laying Made Easy

Transfer Possibilities

Automatic

8. Adjustment Checking . . . .

Page

Power Supply 13

Battery Charging

Maintenance

14. .....14

15. . . 14

16. . 15

17. . 15

18. 15

19. . . . . 16 - 17

20. . . . . . 18 - 19

21. FB-10 Wireless Control . . . 20

22. ......21

9. ........

10. ......13

11. Radio Control . . . . . . . . 13

12. Troubleshooting . . . . . . . 13

13. .........14

Dimensional Sketch

Technical Specifications

Receiver FE-53

Receiver FE-61

Standard Delivery Package

PipeLaser, Optional Acces.

Rotary laser, Optional Acces.

Refraction Effects

11.Radio Control

1. The serial numbers of the laser, FE-53/-61 and FB-10 must correspond with

each other.

2. Simultaneous operation of FE-53/-61 and FB-10 is not possible.

13 - 21

No. Order No. Type Description

01 0001.295 UL-89L Universal laser

02 0037.18 NE-80 Power supply/Battery charger

03 0019.07 Leg set DN 200 (2 x sliding leg/ 2 x fixing leg)

04 0077.36.002 Double headed wrench 10+13

05 0077.36.003 Hexagon key SW 4

06 0077.36 Transport case

1- 6 0001.295.1 UL-89L with standard delivery package

17. Optional Accessories for Pipe Laser

No. Order No. Type Description

01 0016.07 KL-04 Target frame

02 0016.07.002 Plexi target DN 150 - 300

03 0016.07.003 Plexi target DN 400 - 500

04 0019.08 Leg set DN 250 (2 x sliding leg/ 2 x fixing leg)

05 0019.09 Leg set DN 300 (2 x sliding leg/ 2 x fixing leg)

06 0019.10 Leg set DN 400 (2 x sliding leg/ 2 x fixing leg)

07 0019.11 Leg set DN 500 (2 x sliding leg/ 2 x fixing leg)

08 0019.90 Leg adapter for mounting with 3 legs

1- 8 0127.01.1 KL-AU Pipe laying equipment for UL-89L

2345678

09 1035.29 Lightning 2 l

10 1035.27 Storm with digital data display

11 0009.39.1 LE-72 with digital data display

0009.70.1 FE-61

aser receiver

Laser receiver

12 0009.36.1 FE-53 Locking receiver for laser light plane

13 Locking receiver for plumb beam

14 0026.07 FB-10 Two-way radio control

15 0045.04 DS-80 Rotation axis

18. Optional Accessories for Rotary Laser

910 11 14 15

12 13

16. Standard Delivery Package

1cold

warmth

22. Refraction Effects: Example Pipe Laying

The laser beam is deflected to cold air.

It is deformed and moved by atmospheric turbulences.

laser beam

laser beam after temperature influence

laser beam

laser beam after temperature influence

cold warmth

warmthcold

Countermeasures:

Do not keep tubes in direct insolation. Store tubes in the shadow or cover them

with a canvas.

Align the pipe in the ditch immediately. If the laser beam is deformed by

temperature influences and/or in movement, define the centre by averaging.

level tube

in the pipe on the pipe

clamping srews for

vertical adjustment

of target

Functions

20.1 Measuring Receiver

The laser receiver FE-61 receives a stationary or rotating plumb laser beam

and indicates its position to the light plane by way of 2 LEDs.

20.2 Locking Receiver for the Plumb-Axis

It automatically directs the stationary or rotating plumb laser beam to the centre

position of the lasers and locks it there. Accuracy to ± 1mm/100 m.

20.3 Receiver Description

20.6 Outstanding technical specifications:

Accuracy measuring receiver: . . . . . . . . . . . . . . . . . . . to ± 0.1 mm

Accuracy locking automatic: . . . . . . . . . . . . . . . . . . to± 1mm/100 m

Signaltone:............................loud,quietoroff

Power supply: . . . . . . . . . . . . . . 2 x round cell/AA (battery or rech. battery)

Current consumption: . . . . . . . . approx. 100 mA (operating time to 20 hours)

Housing:. . . . . . . . . . . . . . . . . . . . . . watertight, except battery cover

Dimensions / weight: . . . . . . . . . . . . . . . . . 140 x 100 x 32 mm / 0.52 kg

Frequencyrange: .......................2.4GhzISMBand

Transmission power : . . . . . . . . . . . . . . . . . . . . . < 100 mW (EIRP)

Reception: . . . . . . . . . . laser (633 - 815 nm homogeneous beam profile)

..........................Øvon5-20mm,0.8-2mW

Range ...............2to100mdepending on ambient conditions

Distance to illuminants and high-voltage power lines: . . . . . . . . . . > 1.5 m

Conformity with national regulations:

GEO-Feinmechanik GmbH herewith declares that the FE-61 conforms to the

fundamental requirementsand other relevant regulations of directive 1999/5/EG.

= lock automatically

1. x briefly = The radio link with the laser is set up

Once the rotating plumb beam hits the measuring quadrant of the receiver it is

automatically directed to the center and fixed there. By slowly moving the laser

receiver, the position of the light surface is changed. The reception is indicated

by symbols on laser and LEDs on receiver.

LEDs blink alternately right and left: the setting phase is completed.

Switch off receiver to switch off the locking function.

= tone loud, quiet or off

1. x briefly = switch on: The FE-61 works as measuring receiver.

1. x long = switch off

Keep the button pressed until the LED of the operating mode display lights

accompanied by a tone sequence or automatically after 15 min. without receipt.

Switch on the FE-61 and move it to the laser light plane until the reception of

the light plane is indicated by LEDs and signal tones.

To receive the required accuracy, move the FE-61 in arrow direction.

= switch on

20.5 Operation

Remote Control

It is possible to adjust manually the direction and height of the laser with the

FE-61 .

To activate the remote control when turning on the receiver press the power

button until the remote LED flashes.

The side (Y axis) can be adjusted with the keys next to the LED.

Switch to the height (X axis) by briefly pressing the power button.

The remote control LED blinks faster.

Now the height can be adjusted using the buttons next to the LED.

Press briefly to return to the measuring receiver function.

20.4 Control Principle

20. Locking and Receiver FE-61Measuring

Robust Metal Housing

Plastic-coated, watertight.

M5 mounting thread at the back of

the housing.

Power Indicator:

LED blinks slowly = device switched on

LED blinks quickly = battery almost

empty

LED off = device switched off

Battery

Compartment Lid

To open in direction of arrow.

Make sure the polarity is correct

when installing the new battery.

Locking Receiver:

Measuring Receiver:

LED blinks = device switched on

LED off = device switched off

Operating Mode Display

LED blinks = Radio control dial-up

LED off = Radio control connected

LED on = Radio control failure

Remote Control Display

Y-axis: LED blinks slowly

X-axis: LED blinks quickly

Orientation Notches

Measuring Quadrant

with solar cells sensor and

LED display

Apart from the ON button, the functions correspond to those of the keyboard

and display of the laser.

Note: It is not possible to switch on the laser and the radio transmission and

to switch off the laser by the FB-10.

21. Wireless Control FB-10

21.1 Functional Description

The remote control FB-10 allows a wireless operation of GEO lasers with radio

module. Laser and receiver have the same keyboards, operating mode

displays, radio transmitters and receivers.

Range while visual contact up to 350 m.

21.2 Device Description

21.3 Button Description (see 2.)

= ON only FB-10

1 x short =ON: The message "Try to connect .. Please wait .." appears

and the remote control connects to the GEO laser within

approx. 20 seconds.

1. x long = laser beam + rotor switched off (stand-by mode)

2. x long = laser beam + rotor switched on again

Note: Press the button until the desired symbol

or appears.

OFF = Auto off after approx. two minutes if no button pressed.

Robust Metal Housing: plastic-coated, 100 % watertight.

15.4 Error Messages:

"Connection Lost!": Communication between laser and remote control

interrupted - establish visual contact with the laser or

reduce the distance to the laser.

Activate wireless remote control in the menu of the

GEO laser (see instructions for use of laser).

"BATTERYLOW": Replace batteries soon.

The LCD light stays off to save power.

"BATTERYEMPTY!": The batteries must be replaced immediately.

Note: The radio transmission can be switched off either in the second

menu level of the laser or of the remote control. A renewed

switch-on of the radio transmission is possible only at the laser.

LCD-Display

Clearly legible,

illuminated display

Battery Compartment

Cover

To open in direction of arrow.

When inserting the battery

observe the correct polarity.

Antenna

Antenna Lock

Keyboard

Easy to handle, clear

layout, user-friendly.

12.Troubleshooting

1. No laser beam - check battery charge.

2. Low range - clean laser beam exit window.

3. Laser beam blinks slowly - move device into the levelling range by tilting

forwards.

4. Laser beam and banking arrows blink slowly - reset laser from the limitation.

If the errors of points 3 and 4 are not corrected within 2.5 minutes, the device

is switched off automatically.

5. Laser switched off automatically (kick guard or direction automatic

monitoring) - Switch on laser beam by pressing the ON button shortly.

9. Power Supply

7.4 V DC internal lithium ion rechargeable battery or 12 V DC external

rechargeable battery via connection cable 0117.02.

10. Battery Charging

• Carry out charging only with the power and charging unit, type NE-80 or

a 12 V DC external rechargeable battery via connection cable 0117.02.

• Keep charger dry and only use in rooms.

• For charging take the laser out of the transport case.

• Permissible charging temperature 0°C to + 40°C, as best + 10°C to + 25°C.

• After approx. 5 hours the charging time is finished. The display dies down or

the battery symbol shows a full battery.

• Low ambient temperatures reduce the running time, high temperatures

reduce the battery life.

• Damaged batteries must be disposed. Robust Metal Housing

Plastic-coated, watertight.

M5 mounting thread at the back of

the housing.

19. Locking and Measuring Receiver FE-53

Functions

19.1 Measuring Receiver

19.2 Locking Receiver for the X Inclinatin Axis

It directs the rotating laser beam over the whole inclination range automatically

to the centre position of the receiver and locks it there.

The laser receiver type FE-53 receives the rotating laser beam and indicates

its position to the light plane by way of three LEDs and various signal tones

Accuracy to ± 1mm/100 m.

19.3 Receiver Description

Power Indicator:

LED blinks slowly = device switched on

LED blinks quickly = battery almost empty

LED off = device switched off

Battery

Compartment Lid

To open in direction of

arrow. Make sure the

polarity is correct when

installing the new battery.

Locking Receiver

Meas. Receiver ± 0.1 mm

Meas. Receiver ± 1 mm

LED + slow tone sequence

LED + quick tone sequence

LED + steady tone = middle

LED + Tone alternating = middle

Locking Receiver:

Meas. Receiver:

LED blinks = device switched on

LED off = device switched off

Operating Mode Display

LED blinks = Radio control dial-up

LED off = Radio control connected

LED on = Radio control failure

switch over from measuring to locking receiver:

search, find and lock automatically

19.5 Operation

1. x briefly = The radio link with the laser is set-up and the laser light plane is

directed to the centre of the receiver and locked there

automatically.

As soon as the rotating laser beam hits the arrow range of the

receiver, it is automatically directed to the middle and locked

there.

The direction of the laser light plane can be changed by slowly

moving the laser receiver.The reception is indicated by a symbol at

the laser and LEDs at the receiver:

- LEDs blink simultaneously right and left >laser searches for receiver

- LED blinks right or left >receiver found

- LEDs blink alternately right and left >setting finished:

centre found and locked

2. x briefly = laser searches for the receiver again.

Switch off receiver to switch off the locking function.

1. x briefly = Measuring receiver with an accuracy of +/- 1 mm.

Move FE-53 towards the light plane until the reception of the light

plane is indicated by LED and signal tone.

To reach the desired accuracy move the FE-53 in arrow direction:

Accuracy: One LED blinks in the middle = +/- 1 mm

2. x briefly = Measuring receiver with an accuracy of +/- 0.1 mm

Accuracy: Two LED's blink alternately = +/- 0.1 mm

3. x briefly = Back to measuring receiver with an accuracy of +/- 1 mm.

1 x long = Switch off

Press button until the LED of the operating mode display flashes

accompanied by a tone sequence or automatically after 15 min.

without reception.

= tone loud, quiet or off

= switch on/off

19.8 Outstanding Technical Specifications:

Accuracy direction automatic: . . . . . . . . . . . . . . . . . to ± 1 mm/100 m

Accuracy laser receiver: . . . . . . . . . . . . . . . . . . ± 1mm or± 0.1mm

Reception range/-angle: . . . . . . . . . . . . . . . . . . . . . 85mm /> 100°

Rotorspeed:...........................600-1000rpm

Signaltone:............................loud,quietoroff

Power supply: . . . . . . . . . . . . . . 2 x round cell/AA (battery or rech. battery)

Current consumption: . . . . . . . . approx. 100 mA (operating time to 25 hours)

Housing:. . . . . . . . . . . . . . . . . . . . . . watertight, except battery cover

Dimensions / weight: . . . . . . . . . . . . . . . . . 140 x 100 x 32 mm / 0.52 kg

Frequencyrange:........................2.4GhzISMBand

Transmission power : . . . . . . . . . . . . . . . . . . . . . < 100 mW (EIRP)

Guarantee:..............................24months

CE:....................................certified

Range depending on ambient conditions : . . . . . . . . . . . . . 2 to 250 m

Distance to illuminants and high-voltage power lines: . . . . . . . . . . > 1.5 m

Conformity with national regulations:

GEO-Feinmechanik GmbH herewith declares that the FE-53 conform to the

fundamental requirementsand other relevant regulations of Directive 1999/5/EG.

The declaration of conformity can be found at the following address:

http://www.geo-laser.de.In countries with national regulations that are not covered

by European directives the operator must himself check the provisions and

permits for use.

The permit for use is only valid for use with antenna of up to 3 dBi.

laser beam

19.4 Control Principle

The FE-53 can be mounted either on the left or on the right side of the laser.

Because of reasons of functionality, the keyboards of both devices must be

on the same side.

The declaration of conformity can be found at the following address:

http://www.geo-laser.de.In countries with national regulations that are not covered

by European directives the operator must himself check the provisions and permits

for use.

The permit for use is only valid for use with antenna of up to 3 dBi.

Guarantee:..............................................24months

CE: ......................................................certified

Horizontal Set-up

Only control of the Y axis or - after switch-off of the automatic

levelling (see 3.1) - of the Y and X axes.

Vertical Set-Up

Control of the Y and X axes after switch-off of automatic levelling

(see 3.1).

14. Dimensional Sketch

15. Technical Specifications

Laser class Laser type

Range depending on circumstances and receiver

Inclination range

Self-levelling range over the complete inclination range

Speed adjustment

Locking automatic laser light plane: . . . . . up to 250 m with receiver FE-53

Locking automatic plumb beam: . . . . . . . up to 100 m with receiver FE-61

External power supply:. . . . . . . . . . . . 11 to 14 V DC with cable 0117.02

Low battery cut-out

Watertight

Temperature range

eight

Frequency range: . . . . . . . . . . . . . . . . . . . . . . 2.4 Ghz ISM Band

Transmission power :. . . . . . . . . . . . . . . . . . . . . < 100 mW (EIRP)

Guarantee: .............................24months

CE:...................................certified

/ : . . . . . . . . . 3R, < 5 mW/diode, visible red, 635 nm

: . . . . . to 250 m, Ø 500 m

:....................Xaxis -5%to+20%

Inclination range: . . . hz. mounting by tilting forward, X axis - 10 % to + 20 %

Inclination range/direction setting range:. . . . . . . . Y axis - 5 % to + 5 %

Inclination range with rotation of device: . . . . . X axis ± 20 % / Y axis ± 5 %

:............

Readingprecision:........................... 0.001%

Permissible deviation: . . . . . . . . . . . . . . . . . . . . . . ± 5 mm/100 m

:.....................from200-1000rpm

:.............................yes

: ..............................to0.35m

: .....................-10°Cto+50°C

Dimensions/w : . . . . . . . . . . . . . Ø 130 mm,length 295mm/3.6 kg

Operating time with 7.4 V DC Li Ion recharg. battery: . . . . . . to 27 hours

Working distance radio control:. . . . . . . . . . . . . . . . . . . up to 350 m

The range is reduced by obstacles in the way of the radio signal.

Conformity with national regulations:

GEO-Feinmechanik GmbH herewith declares that the devices UL-89L, FB-10,

FE-53 and FE-61 conform to the fundamental requirements and other relevant

regulations of directive 1999/5/EG.

The declaration of conformity can be found at the following address:

http://www.geo-laser.de. In countries with national regulations that are not

covered by European directives the operator must himself check the provisions

and permits for use.

The permit for use is only valid for use with antenna of up to 3 dBi.

13. Maintenance

The laser requires no special maintenance. Keep the electrical connections

clean. Do not clean with water spray. Clean glass parts with a soft, clean cloth.

Store dry.Always transport the laser in its original case.

64Ø

5/8"

152

73,5 20

180Ø

150

200

250

300

400

500

----

103

123

163

204

208

227

240

253

280

307

GEO-Laser GmbH

Solinger Str.8

45481 Muelheim an der Ruhr

Germany

Phone +49 208 99357-0

Fax +49 208 99357-25

info@geo-laser.de

www.geo-laser.de

GEO - partner of the construction industry for 50 years

German Quality Product

Certified

Tabla de contenidos

Otros manuales de Nivel láser de GEO-Laser

GEO-Laser

GEO-Laser NL-9V Manual de usuario

Manuales populares de Nivel láser de otras marcas

Nedo

Nedo ET-5 Manual de usuario

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Manual de usuario

LaserLiner

LaserLiner X2-Laser Manual de usuario

Spectra

Spectra LL300N Manual de usuario

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Manual de usuario

Nedo

Nedo Crossliner 4 Manual de usuario

Lasertec

Lasertec FX360G Manual de usuario

Flex

Flex ALC 8 Manual de usuario

Black & Decker

Black & Decker LZR5 Manual de usuario

Johnson

Johnson 40-6692 Manual de usuario

Cocraft

Cocraft HL 20-SG Manual de usuario

Zircon

Zircon iLine Manual de usuario

HWH

HWH 310 SERIES Manual de usuario

Leica

Leica iCON robot 60 Manual de usuario

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Manual de usuario

LaserLiner

LaserLiner ActiveFinder XP Manual de usuario

DeWalt

DeWalt DW082 Manual de usuario

imex

imex EL20 Manual de usuario