Genesis GBP-ST2000 Guía del usuario
GBP-ST2000
WITH MOSQUITO SCREEN
MOUNTING INSTRUCTION
ROLLER SHUTTER
myeuropeanwindows.com
MOUNTING TYPE "A"
MOUNTING TYPE "B"
MOUNTING TYPE "C"
EXTERNAL ROLLER SHUTTERS MOUNTING TYPES
myeuropeanwindows.com
2.
Dimensioning: H - height of opening S - width of the opening
Measure and mark the place where the holes are made on the guides for
assembly screws. Drill the first hole under the guides in
distance of max. 90mm from the upper edge of the building opening, further
max. every 500mm.
1. Tools necessary to mount the blind.
The GBP LLC does not provide screws and dowels
struts and PVC tubes.
H
S
min 70mm
max 90mm
500mm
500mm
o6o10
3.
Drill the holes in the guides. Drill with a diameter of 6mm make a hole
through the two guide chambers and a drill with a diameter 10mm
increase the opening in the first chamber only from the side outer guide.
MOUNTING TYPE "A"
o10
oo 8
15 mm
4.
When installing the blind with automatic bolts, drill through the central part
of the guide with a drill bit 8 mm in distance 15 mm from the bottom edge.
oo 8
50 mm
5.
When installing a blind with bolts, drill a central one part of the guide
with a drill bit 8 mm in diameter of 50 mm from the bottom edge.
oo 6
35 mm
8 mm
6.
In the case of installing a blind with a cam lock, mill the central part of the
guide with a 6 mm diameter drill in the distance 8 mm from the bottom
edge. The hole should have a length of 35 mm.
MOUNTING TYPE "A" 3
myeuropeanwindows.com
X1
10.
Mark the location for the holes on the wall as they are on the
guide and drill it for the dowels. Insert the dowels into the drilled
holes.
12.
Measure the X1 and X2 dimension of the guide at the bottom and top, and both diagonals D1 and D2 - the discrepancy
between the dimensions X1 and X2, and D1 and D2 should not exceed 2mm.
8.
On the wall, mark the place of drilling for the strap, string or cable.
Then drill 15 mm holes above the upper part of the guide in the
middle of the chamber that introduces the foot of the box.
- on the strap - first with a drill with a diameter of 12mm, then 20mm
- a string - drill with a diameter of 12mm
- from the power cord to the motor - a drill with a diameter of 10mm
15mm
11.
Screw and align the guides using a level on the surface. With blinds
with a mosquito net it is necessary pay attention to put the guides
on the right side so that the latches of mosquito net or system hooks
KLIK-KLAK was located at the bottom of the guide.
X2
D1
D2
7.
Place the drilled guides against the wall and mark the holes
on mounting pins.
9.
After making the hole for the tape, insert the a 20 mm diameter
of PVC tube in the hole and cut evenly with the external face of
the wall (GBP LLC don't provide this element). From the inside
the tube must be shorter by 2 cm from the wall surface, for the
construction of a ribbon grommet.
4MOUNTING TYPE "A"
myeuropeanwindows.com
17.
Mount the retractor vertically in relation to the strap or rope with a
grommet. Lower the shutter, then the strap or rope should be cut
for a length of 25 cm below the mounting location of the retractor.
Pass the strap or rope through the hole in the retractor housing.If
strap used cut a slit and attach to the hook. Holding the spring
housing firmly, turn and release the retractor lock by pushing. If
rope is used, after pushing through the retractor entry hole, light
the tip with a lighter, this prevents the line from unraveling. Close
the retractor and secure it to wall.(see assembly instructions for the
retractor or cable).
16.
Make sure that the blind is properly attached (horizontally and
vertically). Tighten the screws in the guides, then insert the caps.
If necessary mount the bottom plugs of the guides. check proper
functioning of the blind. Check correctness operation of
automatic bolts, bolts or lock, to make adjustments.
13.
Pass the tape (cable or cord) through the hole into building.
19.
The closing height of the mosquito net can be adjusted by
sliding hooks closing the mosquito net, which are located at the
bottom of the guides ...
18. In roller blinds with a mosquito net, check the correctness of
functioning mosquito nets.
14.
Carefully slide the box onto the guide by introducing the profile
slider into the upper part of the guides. Blinds with a mosquito net,
carefully insert the bottom rail so to not
damage the net.
15. Pass the tape or cable through the grommet, then use the
anchor or screw to attach the grommet to wall.
STRING INSTALLATION STRAP INSTALLATION
5
MOUNTING TYPE "A"
STRAP INSTALLATION
STRING INSTALLATION
myeuropeanwindows.com
MOUNTING TYPE "B" & "C"
20.
After the blind is installed we recommend filling the upper and side
gaps between the wall and the roller shutter with silicone seals for
protection against water. Blinds above 200 cm it is recommended to
screw the roller shutter box to the header using flat head screws
every 100 cm.
MOUNTING TYPE "B" & "C"
o6o10
o10 o6o10
MOSQUITO NET WITH KLIK-KLAK
... after unscrewing the Allen screws with the 2mm key, please
use a screwdriver to move the hooks up or down. In the case of
the KLIK-KLAK system, unscrew the screw with the key 3mm
hexagon socket and set to the desired height.
1.
Drill the holes in the guides. Use a 6mm drill bit to drill a hole through the two guide chambers and a 10mm drill bit
increase the opening in the first chamber only from the outer side of the guide (TYPE OF ASSEMBLY C - increase the hole in the middle wall
the guide).
3.
Place the drilled guides against the wall and mark the holes
for screws on the window frame.
4.
Place the drilled guides to the wall and mark holes for mounting
screws in the side of the opening
6
When installing external blinds with mosquito nets in installation type B (in the opening) in some cases
it may happen that the handles of the bottom bar of the mosquito net can be held by the window frame. Then it
is recommended installation of blinds on spacing strips or removal of holders, and change from the bottom slat
gasket mosquito screens from the side channel to the bottom channel. Handles located in the bottom strip of the
mosquito net are not indispensable element but facilitate the use of mosquito nets.
MOUNTING "B" MOUNTING "C"
MOUNTING "B" MOUNTING "C"
myeuropeanwindows.com
MOUNTING "B"
5. Drill holes in the marked places on the window frame for the
screws.
... when assembling C - drill holes in the marked places on the wall.
6. Carefully slide the box into the guide by introducing the profile
sliders into the upper part of the guides. Blinds with a mosquito
net, carefully insert the bottom latch making sure not damage the
netting and pay attention to the KLIK-KLAK system at the bottom
of the guide.
8.
Carefully insert the box with the standard guides or angular in the
window opening.
25 mm
7.
With the type of mounting into the openings on the window frame as
a manual drive, the company GBP LLC recommends the rope
retractor. Place on the window frame drilling into a cable or cord.
Then drill the hole 2.5 cm under the upper part of the recess.
- a cable - a drill with a diameter of 12mm
- from the power cord to the motor - a drill with a diameter of 10mm
9. Push the strap or rope through the guide, then the grommet and
screw to the wall.
MOUNTING TYPE "B" & "C"
MOUNTING "B"
10.
Screw and align the guides using a level guide to the surface.
7
MOUNTING "C"
MOUNTING "B" MOUNTING "C"
myeuropeanwindows.com
MOUNTING TYPE "B" & "C"
MOUNTING "C"
11.
Make sure that the blind is properly mounted (horizontally and
vertically). Tighten the screws in the guides and then insert caps. Check
the correct functioning of the blind. Check the correct operation of
automatic bolts and bolts or lock, adjust if necessary.
13.
Lower the shutter blinds, then the straps or rope should be cut
for a length of 25 cm below the mounting location of the
retractor. After put the rope through the retractor hole, and light
with a lighter, this will prevents it from unraveling the rope. Close
retractor and attach it to the wall. (see assembly instructions
cable retractor).
12.
The retractor should be screwed to the wall or window frame
vertically in relation to the cable outlet from the grommet.
The retractor should be located no more than 1.8 m from the ground.
8
myeuropeanwindows.com
SHUTTERS OPERATION
1. Raising the blind
Grab the strap and pull it down. During this time, the loose part of the tape will be rolled up to the
retractor and the roller shutter's blind will rise to a certain height. Repeat the procedure several times
until the blinds stops by the limiters mounted in the bottom bar and the blind is completely open. The
last movement of the tape should be made slowly so that the stops do not hit the roller shutter box too
much.
2. Lowering the blind
Grab the strap just above the retractor and pull it towards you at an angle of about 20 degrees to release
the retractor lock. Then, holding the tape, it should be moved gently towards the window, so that the
falling blind will pull the tape inside. Repeat the procedure several times until the blind is completely
closed. When lowering the shutter, make sure it does not hit the bottom too much.
When lifting and lowering the blind, it can be stopped anywhere, leaving the room partially shaded. When
lifting and lowering the blind, make sure that the movement of the tape is perpendicular to the exit of the
tape from the box. Tape deviations can cause it to bend and jam.
OPERATION MANUAL
ROLLER SHUTTER WITH MOSQUITO SCREEN
9
myeuropeanwindows.com
SHUTTERS OPERATION
Drive for a crank with Cardan joint:
In blinds equipped with a crank lifting mechanism with a cardan gear, the crank is supplied with a blind.
After installing the blind, place the crank rod in the gearbox through the hole in the roller shutter box. Next
- depending on the type of blind installation - the crank should be screwed to the box or using wall plugs
to the wall of the building. An additional element fixing the crank arm is a special clamp, which is screwed
by means of screws (dowels) to the wall in the lower part of the crank arm. The design of the crank arm
thanks to special joints allows you to "straighten" it for aesthetic purposes when the blind is not operated.
To raise or lower the blind jacket, turn the crank in the right direction.
The operation of the crank lifting mechanism requires special care and feeling, as the gear used allows
for obtaining large forces that may damage the shutter elements. Therefore, stop turning the crank when
you feel resistance or notice that the roller shutter has stopped when lowering. In external blinds, the
rotation of the crank clockwise causes lowering of the roller shutter, while the rotation of the crank
counter-clockwise causes the roller blind to be lifted
Spring drive:
1. Raising the blind.
Grab the handle in the bottom strip and hold the blind. Use the key to release the lock. Slowly release
the blind. The blind will roll up automatically and will stay open.
2. Closing the blind:
Hold both handles in the lower bar with both hands and evenly pull the blind down. Hold the blind in the
lower position and turn the key to lock the blind.
10
myeuropeanwindows.com
Otros manuales para GBP-ST2000
1
Tabla de contenidos
Otros manuales de Mobiliario de interior de Genesis
