Generac Power Systems 0830890SRV Manual de usuario

PRODUCT INFORMATION BULLETIN

for Control Board # 0830890SRV

SUBJECT: C Option Engine Control PCB Adjustment Procedure

MODELS AFFECTED: All generator sets utilizing a C Option control panel.

PROBLEM: Overspeed and starter disengage calibration.

CORRECTIVE ACTION: This adjustment must be done to ensure proper operation.The following

adjustment is for setting the engine OVERSPEED shutdown function.This

adjustment also serves as the starter disengage speed setpoint. If this adjust-

ment is not properly made it could cause damage to the engine or alternator

in an overspeed condition, or to the starter and ring gear if the starter does

not properly disengage.

1. Before starting the generator, turn COARSE adjustment pot full

CLOCKWISE, FINE pot COUNTER-CLOCKWISE.

2. Start engine, make sure engine is up to rated speed.

3. Turn COARSE pot slowly until red LED on PCB board turns on.

4. Turn FINE pot slowly until red LED goes out.

5. Turn FINE pot back slowly until red LED turns back on.

6. Verify proper overspeed shutdown by manually increasing engine speed

until engine shuts down.Verify that engine shutdown occurs at 72 Hz. If

not, slightly adjust FINE pot to achieve proper shutdown speed.This will

also ensure that the starter disengages at approximately 500 rpm.

Replaces PIB02-9-S

MORE DETAILED INSTRUCTIONS on the back page.

1. On the circuit board, locate potentiometers R26 and R27. See Figure 1. Also, locate the

red LED.

2. Turn the COARSE (R26) pot all the way clockwise (CW).

3. Turn the FINE (R27) pot all the way counterclockwise (CCW).

4. Start the generator engine manually, using the Start/Stop switch. Let the engine stabilize

and warm up at no-load. If necessary, adjust the engine

governor to obtain normal rated operating speed.

5. With the unit running at no-load and at its normal rated speed, slowly turn the COARSE

(R26) pot counterclockwise (COW) until the red LED just turns on.

6. Slowly turn the FINE (R27) pot clockwise (CW) until the red LED just goes out.

7. Slowly, turn the FINE (R27) pot counterclockwise (CCW) until the red LED just turns on.

With the board properly calibrated, overspeed shutdown will occur at approximately 10

Hertz above the unit's normal operating frequency. For example, if the engine no-load

speed is 62 Hertz, overspeed shut-down will occur at

approximately 72 Hertz.

MORE DETAILED INSTRUCTIONS from Generac Diagnostic Repair Manual # 79247:

CAUTION: Steps 2 and 3 MUST be completed BEFORE THE ENGINE IS STARTED. If the engine is

started before the steps are completed, an over-speed shutdown may occur at normal rated operating

speed.

PRODUCT INFORMATION BULLETIN

for Control Board # 0830890SRV

Tabla de contenidos

Otros manuales de Generador portátil de Generac Power Systems

Generac Power Systems

Generac Power Systems 005714-0 Manual de usuario

Generac Power Systems

Generac Power Systems PowerBOSS Storm-Plus 1642-0 Manual de usuario

Generac Power Systems

Generac Power Systems G0062540 Hoja de instrucciones

Generac Power Systems

Generac Power Systems iQ2000 Manual de usuario

Generac Power Systems

Generac Power Systems Automatic Standby Generator Manual de usuario

Generac Power Systems

Generac Power Systems XG4000 Manual de usuario

Generac Power Systems

Generac Power Systems Generator Manual de usuario

Generac Power Systems

Generac Power Systems NP45G Series Manual

Generac Power Systems

Generac Power Systems 8 kW LP Manual de usuario

Generac Power Systems

Generac Power Systems Automatic Standby Generators Manual de usuario

Generac Power Systems

Generac Power Systems 006719-0 Manual de usuario

Generac Power Systems

Generac Power Systems GP7500E-5943-5 Manual de usuario

Generac Power Systems

Generac Power Systems GP Series Manual de usuario

Generac Power Systems

Generac Power Systems 005793-0 Manual de usuario

Generac Power Systems

Generac Power Systems 1338-1 Manual de usuario

Generac Power Systems

Generac Power Systems LP3250 LP SERIES Manual de usuario

Generac Power Systems

Generac Power Systems XP Series Manual de usuario

Generac Power Systems

Generac Power Systems GP Series Manual de usuario

Generac Power Systems

Generac Power Systems XP4000 Professional Manual de usuario

Generac Power Systems

Generac Power Systems 7500 Manual de usuario

Generac Power Systems

Generac Power Systems GP6500E GP SERIES Manual de usuario

Generac Power Systems

Generac Power Systems GP8000 Manual de usuario

Generac Power Systems

Generac Power Systems Mobile Power MMG465 Manual de usuario

Generac Power Systems

Generac Power Systems IX1600 Manual de usuario

Manuales populares de Generador portátil de otras marcas

Kohler

Kohler 20EORZ Manual de instrucciones

Powerhorse

Powerhorse 83171 Manual de usuario

HURST

HURST ML-630-SI Manual de usuario

ETQ

ETQ TG4000 Manual de usuario

Briggs & Stratton

Briggs & Stratton 40265 Guía de configuración

ConMed

ConMed 7550 Manual de usuario

Owon

Owon Waveform Generator Manual de usuario

evertz

evertz 7700 Series Manual de usuario

Power Stroke

Power Stroke PS906025 Manual de usuario

Firefly

Firefly Cygnus CYG2400/460/24 Manual de usuario

Draper

Draper PG950S Actualización de firmware

PowerBoss

PowerBoss PowerBoss Manual de usuario

SDMO

SDMO SH 4000 Manual de usuario

EINHELL

EINHELL STE 5500 Manual de usuario

Wanco

Wanco WI3000P Manual de usuario

Full Boar

Full Boar FBT-3300 Manual de usuario

Dwyer Instruments

Dwyer Instruments ASG Manual de usuario

Westinghouse

Westinghouse WH1000i Series Manual de usuario