Gemtek WX-5525G Manual de usuario
High Speed Access Point Router
WX-5525G
User's Manual
Mar. 19, 2003 (Draft 1.0
Gemtek Technology Co., Ltd.
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
1
CONTENTS
Introduction ..................................................................................................2
Hardware Installation .............................................................................4
WX-5525G AP Router Default Settings .……..…………………………..5
Web Management Settings ………..…………………………………………6
Setup …………...………………………………………………………….7
Security…………. …..…………………………………………………. 11
System …………………………………………………………………….13
DHCP ……………………………………………………………………..16
SNMP …………………………………………………………………… 18
Status ……………………………………………………………………...18
Advanced Wireless ……………………………………………………… 20
Filters …………………………………………………………………… 22
Port Forwarding …………………………………………………………24
Routing ………………………………………………………………… 26
DDNS ………………………………………………………………… 28
Troubleshooting ………………………………………………………………29
Technical Specifications ……………………………………………………..31
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
2
Introduction
Thank you for purchasing your WX-5525G Dual Band Wireless AP Router.
This user guide will assist you with the installation procedure.
The package you have received should contain the following items:
•WX-5525G Dual Band Wireless AP Router
•User Guide
•Power Supply / Cord
•Ethernet Cable
Note: if anything is missing, please contact your vendor
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
3
Safety Notification
Your Wireless AP Router should be placed in a safe and secure location. To ensure proper
operation, please keep the unit away from water and other damaging elements.
!Please read the user manual thoroughly before you install the device.
!The device should only be repaired by authorized and qualified personnel.
!Please do not try to open or repair the device yourself.
!Do not place the device in a damp or humid location, i.e. a bathroom.
!The device should be placed in a sheltered and non-slip location within a temperature
range of +5 to +40 Celsius degree.
!Please do not expose the device to direct sunlight or other heat sources. The housing
and electronic components may be damaged by direct sunlight or heat sources.
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
4
Hardware Installation
Front Panel
The front panel provides LED’s for device status. Refer to the following
table for the meaning of each feature.
LED STATUS Description
Off No Power
Red On 1. Power on 2. Reset to default 3. Firmware upgrade (first 1 minute)
PWR/STAT Red Blink 1. System up 2. Power on 3. Firmware upgrade
Off no Ethernet link detected
LAN Green On 10/100Mbps Fast Ethernet link detected. No activity.
Green Blink Indicates data traffic on the 10/100 Mbps LAN
Orange On 10Mbps Ethernet link detected. No activity.
WAN Orange Blink Indicates data traffic on the 10 Mbps WAN.
G Yellow Blink Indicates the device is linking or active data through wireless links
Rear Panel
The rear panel features 4 LAN ports, 1 WAN port and Reset button.
Refer to the following table for the meaning of each feature.
Power
(DC 5v) Used to connect to the power outlet. Only use the power adapter
provided with the device. Use of an unauthorized power adapter
may cause damage to your device and violate your warranty.
Reset Press the Reset Button for approximately ten seconds, all
configurations will set to factory default settings.
LAN The RJ-45 Ethernet ports used to connect your PC, hub, switch or
Ethernet network.
WAN The RJ-45 Ethernet port labeled WAN is used to connect your AP
Router to your xDSL or Cable modem.
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
5
WX-5525G AP Router Default Settings
The default settings are shown following.
User Name admin
Password admin
AP Router IPAddress 192.168.1.1
AP Router Subnet Mask 255.255.255.0
RF ESSID Wireless Router
11b RF Channel 6
RF Roaming Enabled
Encryption Disabled
DHCP client Enabled
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
6
Web Management Settings
START -UP & LOG IN
In order to configure the WX-5525G Wireless AP Router, please use your web
browser (Microsoft Internet Explorer or Netscape) and manually input 192.168.1.1 into the
address box (as shown below) and press Enter key.
In order to configure the WX-5525G Wireless AP Router, please input the user-name
into the User Name box. Enter the password into the Password box and press the OK
button. The default username is admin, and the default password is admin
Once you have logged-in as administrator, it is a good idea to change the
administrator password to ensure a secure connection to the Wireless AP.
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
7
MAKE CORRECT NETWORK SETTINGS OFYOUR COMPUTER
To change the configuration, use Internet Explorer (IE) or Netscape Communicator to
connect the WEB management 192.168.1.1
Setup
This screen contains all of the Router's basic setup functions. Most users will be able to use
the Router's default settings without making any changes. Click the Apply button to save
your changes.
Most users will be able to configure the AP Router and get it working properly using the
settings on this screen. Some Internet Service Providers (ISPs) will require that you enter
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
8
specific information, such as User Name, Password, IPAddress, Default GatewayAddress,
or DNS IPAddress. This information can be obtained from your ISP, if required.
Host Name: This entry is necessary for some ISPs and can be provided by them.
Domain Name: This entry is necessary for some ISPs and can be provided by them.
Configuration Type: The Router supports four connection types:
Automatic Configuration - DHCP
Static IP
PPPoE (Point-to-Point Protocol over Ethernet)
PPTP (Point-to-Point Tunneling Protocol)
These types can be selected from the drop-down menu next to Internet Connection. The
information required and available features will differ depending on what kind of
connection type you select.
Some descriptions of this information are included here:
•
Internet IP Address and Subnet Mask
This is the Router's IP Address and Subnet Mask as seen by external users on the
Internet (including your ISP). If your Internet connection requires a static IP
address, then your ISP will provide you with a Static IP Address and Subnet Mask.
•
Default Gateway
Your ISP will provide you with the Gateway IP Address.
•
DNS (Domain Name Server) IP Address
Your ISP will provide you with at least one DNS IP Address.
•
User Name and Password
Enter the User Name and Password you use when logging onto your ISP through
a PPPoE or PPTP connection.
•
Connect on Demand
You can configure the Router to disconnect your Internet connection after a
specified period of inactivity (Max Idle Time). If your Internet connection has been
terminated due to inactivity, Connect on Demand enables the Router to
automatically re-establish your connection as soon as you attempt to access the
Internet again. If you wish to activate Connect on Demand, click the radio button.
If you want your Internet connection to remain active at all times, enter 0in the
WX-5525R Dual Band AP Router
Wireless Broadband Anywhere
9
Max Idle Time field. Otherwise, enter the number of minutes you want to have
elapsed before your Internet connection terminates.
•
Keep Alive Option
This option keeps you connected to the Internet indefinitely, even when your
connection sits idle. To use this option, click the radio button next to Keep Alive.
The default Redial Period is 30 seconds (in other words, the Router will check the
Internet connection every 30 seconds).
IP Address and Subnet Mask: This is the Router's IP Address and Subnet Mask as seen
on the internal LAN. The default value is 192.168.1.1 for IP Address and 255.255.255.0
for Subnet Mask.
Wireless:
2.4GHz Settings
Mode:
The default setting is Mixed.
If you have Wireless-G and 802.11b devices in your network, then keep the default setting, Mixed. If
you have only Wireless-G devices, select G-Only. If you want to disable wireless networking, select
Disable.
Channel: The default setting is 6.
Select the appropriate channel from the list provided to correspond with your network settings,
between 1 and 11 (in North America). All devices in your wireless network must use the same
channel in order to function correctly.
Channel: Select the appropriate channel from the list provided to correspond with your
network settings. You shall assign a different channel for each AP to avoid signal
interference.
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de Gemtek
