Gemtek Systems T-316 Manual de usuario
Wi-Fi Ethernet Smart Client
T-316
User’s Manual
Revision1.0
T-316
User’s Manual
Copyright © 2002 Gemtek Systems, Inc.
2
Gemtek Systems reserves the right to change specifications without prior notice.
While the information in this manual has been compiled with great care, it may not be deemed an assurance of product
characteristics. Gemtek Systems shall be liable only to the degree specified in the terms of sale and delivery.
The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is
subject to written authorization from Gemtek Systems.
The product described in this book is a licensed product of Gemtek Systems, Inc.
Microsoft, Windows 95, Windows 98, Windows Millennium, Windows NT, Windows 2000, Windows XP, and MS-DOS are
registered trademarks of the Microsoft Corporation.
Novell is a registered trademark of the Novell,Inc.
MacOS is a registered trademark of Apple Computer, Inc.
Java is a trademark of Sun Microsystems, Inc.
Wi-Fi is a registered trademark of Wireless Ethernet Compatibility Alliance.
All other brand and product names are trademarks or registered trademarks of their respective holders.
Copyright © 2002 Gemtek Systems, Inc
All Rights Reserved
Notice
Trademarks
3
Contents
1. Introduction..................................................................................................4
2. Installation....................................................................................................5
3. Configuring the Wireless Ethernet Client .....................................................6
4. Contents of Web Interface ...........................................................................7
4.1 Info Page ............................................................................................7
4.2 Wireless Settings................................................................................8
4.3 Bridging Table.....................................................................................9
4.4 IP Setting ..........................................................................................10
4.5 Administration ................................................................................... 11
4.6 Security.............................................................................................12
5. Troubleshooting.........................................................................................14
6. Technical Specification of Wireless Ethernet Client...................................15
4
1. Introduction
Thank you for purchasing the T316 Wireless Ethernet Smart Client.
This manual will assist you with the installation procedure.
The package you have received contains the following items:
• 11Mbps Wireless Ethernet Client
• Cat.5 Ethernet with USB power extractor cable
• CD
Note: if anything is missing, please contact your vendor.
T316 allows for one Ethernet-enabled device (e.g., Windows/MAC/Linux/UNIX
Desktop PC or laptop) to be instantly connected to an existing 802.11b wireless
network. Taking full advantage of the integrated Web server capability, T316 is
performed through a simple Web browser user interface for easy configuration.
Besides laptop or desktop environment, T316 is also the ideal solution to make
other network device such as network printer or camera becomes a wireless
station.
5
2. Installation
1. Mount T316 Wireless Ethernet Smart Client to your device firmly.
2. Insert the power connector.
3. Attach the Wireless Ethernet Client to the Ethernet network using a UTP
Ethernet cable.
At the front of the Wireless Ethernet Client you will see three LEDs.
If all go well, the Power LED is red and the LINK and ACT LED will be blinking
whenever there is traffic on the wired and wireless networks respectively.
Reset the Wireless Ethernet Client
If you press the reset button for more than four seconds, the Wireless Ethernet
Client will be reset to the default factory settings. All changes you made to the
configuration will be lost.
1. Insert one end of a paper clip into the hole of reset button and keep it pressed
for more than four seconds. LINK LED will be blinking during the process.
2. Release the reset button after ACT LED goes off. All settings will be deleted and
back to the default. You can refer to this manual and reconfigure the Wireless
Ethernet Client by yourself.
6
3 Configuring the Wireless Ethernet Client
The Wireless Ethernet Client is a ready-to-use device. It is delivered with default
settings that allow you to have access to it without configuring it. When this
message window pops up, press OK to access web configuration page. No user
name and password needed.
You can configure the Wireless Ethernet Client via a JavaScript-enabled
web-browser such as Internet Explorer 4.0 or higher, or Netscape Navigator 4.0 or
higher.
Factory Default Settings for the Wireless Ethernet Client
SSID default
Channel 6
Transmission rates Auto
WEP enable No
IP Address mode Static
IP Address 192.168.5.99
Subnet mask 255.255.0.0
User Name Blank
Administrator or password Blank (no password needed)
The computer that you are using for initial configuration must have an IP Address
within the same range as the IP Address of the Wireless Ethernet Client.
The Wireless Ethernet Client has a default IP Address of 192.168.5.99 with
a subnet mask of 255.255.0.0
7
4. Contents of Web Interface
4.1 Info Page
The Info window displays the current setup status of the Wireless Ethernet Client.
Communication Quality
Specifies the Communications Quality of the Basic Service Set to which the station
is currently connected. The value for the field of this record is based on signal level
and noise level measurements.
Firmware Version
This indicates the Wireless Ethernet Client’s firmware version.
Current setting of IP Address
It shows IP address of the wireless Ethernet Client.
8
Non-IP MAC Address
The MAC Address of Ethernet port that bridges to Wireless Ethernet Client.
4.2 Wireless Settings
The settings of the wireless device are displayed here, and you can edit some of
these settings.
Operating Mode: Infrastructure
This is the default setting. Switch to Ad-Hoc mode when communicating to another
client device without the presence of Access Point.
SSID
The SSID is also known as Service Set ID. This is the name of your wireless
network. Only Wireless Ethernet Clients and clients that share the same SSID are
able to communicate with each other.
P.S. You can leave this blank and then reboot it to scan the environment
You will see what AP available around you at Info page.
Channel
This is the channel that the Wireless Ethernet Client uses to transmit and receive
data. The channel that you select here is restricted to the channels that can be
9
used within your regulatory domain.
TX rate
The transmit rate identifies the preferred data transmission speed of the Wireless
Ethernet Client. Transmissions at faster rates allow for higher data throughput and
quicker network response times. However, transmissions at lower rates are usually
more reliable and cover longer distances than the higher rates.
Access Point Density
When connecting to the Access Point, it is generally necessary to specify an
Access Point Density. This provides some control over handoff of clients during
roaming between Access Points. Three values, Low, Medium, and High
4.3 Bridging Table
The table lists your device that is bridging with the Wireless Ethernet Client.
10
4.4 IP Setting
Static
Select Static (recommended) to assign the IP, Subnet Mask and Gateway
Address.
DHCP
If the Wireless Ethernet Client is part of a network with a DHCP server, the DHCP
server will assign the IP settings to the Wireless Ethernet Client automatically.
(This is not recommended because a DHCP-assigned IP Address will change
frequently, making the Wireless Ethernet Client impossible to configure.)
Device Name
Assign the name of the Wireless Ethernet Client.
Allow Upgrade Uploads
Select this checkbox when performing firmware upgrade.
Otros manuales para T-316
1
Tabla de contenidos
Otros manuales de Enrutador de red de Gemtek Systems
Gemtek Systems
Gemtek Systems P-380 Manual de usuario
Gemtek Systems
Gemtek Systems R921212G Manual de usuario
Gemtek Systems
Gemtek Systems BC-4GMCPGa Manual de usuario
Gemtek Systems
Gemtek Systems WLTFQT141GN Manual de usuario
Gemtek Systems
Gemtek Systems WLTFQR-121 Manual de usuario
Gemtek Systems
Gemtek Systems CPE7000 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad