Gefen EXT-DVI-2-HDSDIPRO Manual de usuario

www.gefen.com

DVI to HD-SDI

Pro Scaler

EXT-DVI-2-HDSDIPRO

Technical Support:

Telephone (818) 772-9100

(800) 545-6900

Fax (818) 772-9120

Technical Support Hours:

8:00 AM to 5:00 PM Monday through Friday Paciﬁc Time

Write To:

Gefen Inc.

C/O Customer Service

20600 Nordhoff Street

Chatsworth, CA 91311

www.gefen.com

[email protected]

Notice

Gefen, LLC reserves the right to make changes in the hardware, packaging, and

any accompanying documentation without prior written notice.

The DVI to HDSDI PRO is a trademark of Gefen LLC

All trademarks are the property of their respective owners.

All trademarks are the property of their respective companies.

ASKING FOR ASSISTANCE

Rev A3

TABLE OF CONTENTS

Introduction

Operation Notes

Panel Descriptions

Menu Functions

Supported Input/Output Resolutions

RMT-8HDS-IR Installation

RS-232 Control and Firmware Update Procedure

Speciﬁcations

Warranty

INTRODUCTION

The Gefen DVI to HDSDI Pro Scaler combines two of our DVI to HDSDI Scaler

Plus units into one rack-mountable unit. It still incorporates full single-link DVI-D

conversion scaled to your choice of SD/HDSDI Single- or Dual-link modes, but now

simpliﬁes your rack. Resolutions of up to 1080p are supported over the HDSDI link

for those that want true “High Deﬁnition.” Performance has been greatly enhanced

due to Gennum’s VXP Scaler circuitry onboard, allowing for new features such as

Genlock, Color & Gamma Correction, Noise Reduction, Detail Enhancement, Aspect

Ratio Selection, Pattern Generator Mode, and Multiple Language Menu Support.

Bottom Line? More performance, less cost.

DVI devices are connected to the DVI inputs and SDI devices are connected to the

SDI outputs. When the source, display and the Scaler are powered and connected,

video signals are converted to the proper format. There are two separate menu

systems for each integrated DVI to HDSDI box. Input 1 is labeled as the Master

device in the menu system while Input 2 is labeled as the Slave device. Please refer

to page 2 on how to access each separate menu system

CONTENTS

The DVI to HD-SDI Pro consists of:

(1) DVI to HDSDI Pro Scaler unit

(2) 6 foot DVI Cable (m-m)

(1) DB-9 Cable

(1) RMT-8HDS-IR Remote Control

(1) Rack Ears

(1) 5V Universal DC Power Supply

(1) User Manual

HOW IT WORKS

OPERATION NOTES

On power up, the DVI to HD-SDI Pro will automatically detect the format of the input

signal. The unit is controlled using the included remote or through the RS-232 port.

The following are the buttons for the RMT-8HDS-IR Remote Control Unit (included):

- UP (Navigates cursor up)

- LEFT (Navigates cursor left)

- Enter (Accept Operation / Return to Menu)

- RIGHT (Navigates cursor right)

- DOWN (Navigates cursor down)

- MENU (Show / Hide On screen Display)

- OUTPUT (Change Output Format)

- SOURCE (Non operational)

To bring up the on screen menu for the master device, press the MENU button once.

To bring up the menu for the slave device, press the MENU button again. Pressing

the MENU button once more will exit the menu system. Navigation is done using

Buttons up, left, right, and down; Push the Enter button to accept the cursor focus.

Pressing the Output button cycles through the following output modes:

480i - 576i - 720p - 1080i

Other functions and output modes can be accessed through the on screen menu.

To Restore I/O settings, simply recycle power on the Scaler

*Note: The IR Remote Control Unit has a small bank of adjustment switches known

as DIP (Dual Inline Package) switches located inside the battery compartment. Both

DIP switches under the remote battery cover must initially be in the OFF position

to communicate with the Scaler, as they control the IR frequency used. Please see

page 7 for more information on how to set the DIP switches.

RMT-8HDS-IR

Remote Control

Unit

DIP

switches

Front Back

PANEL DESCRIPTIONS

Front

Back

Power LED

Indicator

IR Receiver 2IR Receiver 1

Power Input

DVI

Input 1 DVI

Input 2

RS-232

Port 1 RS-232

Port 2

GenLock

Reference

Input 1

DVI to HDSDI Unit 1 DVI to HDSDI Unit 2

GenLock

Reference

Input 2

HD-SDI

Output 1 HD-SDI

Output 1

HD-SDI

Output 2 HD-SDI

Output 2

Menu Functions

Aspect:

-Full Screen: Stretches input to ﬁll the Monitor.

-Letter / Pillar Box: Sets the aspect ratio to ﬁt a letter or pillar box format.

-Panoramic: Panoramic Zoom feature

-Extract: Feature to magnify the signal.

-Extract Size: Adjusts signal magniﬁcation.

-Horizontal / Vertical Position: Moves the magniﬁed signal

Horizontally and Vertically

-Through: Feature to crop the signal.

-Horizontal / Vertical Size: Horizontally and Vertically contracts

or expands the cropping viewport.

-Horizontal / Vertical Position: Move the signal Horizontally or

Vertically inside the cropping viewport.

Layout:

-Size and Position:

-Horizontal / Vertical Size: Adjust Horizontal or Vertical

resolution.

-Horizontal / Vertical Position: Move image Horizontally or

Vertically.

Picture:

-Image Color:

-Contrast: Individually adjust the contrast for red, green and blue

-Brightness: Individually adjust the brightness for red, green and

blue

-Black level: Adjust black levels between 0 (default) and 100

-Detail Enhancement:

-Detail Enhancement: Digitally enhance signal

-Noise Threshold:Adjusts noise allowed in detail enhancement

-Noise Reduction: Digitally reduce signal noise

-Motion Threshold

Menu Functions (continued...)

Input:

-Input Video Format: Auto Detect by default. Signal can be forced to a speciﬁc

High-deﬁnition resolution. (Please see Supported Input/Output Resolutions for

more information).

-Input Graphic Format: Auto Detect by default. Signal can be forced to a

speciﬁc computer resolution. (Please see Supported Input/Output Resolutions

for more information).

-Clean Aperture:

-Horizontal and Vertical Size: Stretch image Horizontally or Vertically

-Horizontal and Vertical Position: Move image in view port Horizontally

or Vertically

-Non-standard sync

-Remote Channel: Changes the IR code of the DVI to HDSDI Scaler to one of 4

different settings between 0 and 3. When the remote channel is changed, dip

switches in the remote must be changed to the corresponding code in

order to continue operating the DVI to HDSDI Scaler.

(Please see RMT-8HDS-IR Installation page for more information.)

Output:

-Output Format: Select the desired output resolution. (Please see Supported

Input/Output Resolutions for more information).

-Link Conﬁguration

-Genlock Reference: Locks input clock in sync with output clock. 2 locking

methods by either the DVI input or the Reference input.

(Note: feature only works if input and output frequencies are multiples of each

other)

-Language: Set menu to display English or French text.

-Gamma Correction:

-Default: Set for Default Gamma settings.

-sRGB

-Custom: Enables Gamma Coefﬁcient menu item as the current

Gamma coefﬁcient.

-Gamma Coefﬁcient: (0.3 - 3.0); Default set at 1.0.

Patterns:

-Color Bars: Display color bar video pattern.

-Cross Hatch: Display cross hatch video pattern.

General:

-Save conﬁguration

-Restore default conﬁguration

SUPPORTED INPUT/OUTPUT RESOLUTIONS

Input Video Formats Supported:

480i 10305i/59.94 1080p/50M

480p 1035i/60 1080p/59.94

576i 1080i/50 1080p/60

576p 1080i/50M 1080sf/23.98

720p/23.98 1080i/59.94 1080sf/24

720p/24 1080i/60 1080sf/25

720p/25 1080p/23.98 1080sf/29.97

720p/29.97 1080p/24 1080sf/30

720p/30 1080p/25 2K-p/23.98

720p/50 1080p/29.97 2K-p/24

720p/59.94 1080p/30 2K-sf/23.98

720p/60 1080p/50 2K-sf/24

Input Graphic Format Supported:

640x350/85 1024x768/85 1366x768/60

640x400/85 1280x854 1366x923/50

640x480/60 1152x864/75 1440x900/60

640x480/75 1280x768/60 1440x1080/60

640x480/85 1280x960/60 1440x1080/60

800x600/60 1280x960/85 1600x1024

800x600/75 1280x1024/60 1600x1200/60

800x600/85 1280x1024/75 1680x1050/60

1024x768/60 1280x1024/85 1920x1200/60

1024x768/75 1360x768/60 2048x1080

Output video formats supported:

480i 10305i/59.94 1080p/50M

480p 1035i/60 1080p/59.94

576i 1080i/50 1080p/60

576p 1080i/50M 1080sf/23.98

720p/23.98 1080i/59.94 1080sf/24

720p/24 1080i/60 1080sf/25

720p/25 1080p/23.98 1080sf/29.97

720p/29.97 1080p/24 1080sf/30

720p/30 1080p/25 2K-p/23.98

720p/50 1080p/29.97 2K-p/24

720p/59.94 1080p/30 2K-sf/23.98

720p/60 1080p/50 2K-sf/24

RMT-8HDS-IR Installation

1. Remove battery cover from the back of the RMT-8HDS-IR remote.

2. Verify that DIP switches 1 & 2 are in the down (OFF) position.

3. Insert the battery, hold the battery so that you can see the positive side facing up.

The side that is not marked must be facing down.

4. Test the RMT-8HDS-IR remote by pressing ONLY one button at a time. The indi-

cator light on the remote will ﬂash once each time you press a button. WARNING:

Do not press multiple buttons simultaneously and do NOT press buttons rapidly.

These actions will cause the remote to reset and steps 1-4 will have to be repeated.

Note: The RMT-8HDS-IR ships with two batteries. One battery is required for opera-

tion, the second battery is a spare.

The following are the DIP switch combinations that correspond to the Remote Code

menu option on the DVI to HDSDI Scaler (Please see Menu Functions section for

more information):

Remote Channel 0:

Remote Channel 1:

Remote Channel 2:

Remote Channel 3:

Battery

Compartment DIP Switches

RMT-8HDS-IR Remote Control Unit (Back)

Tabla de contenidos

Otros manuales de Amplificador de Gefen

Gefen

Gefen HDTV-148S Manual de usuario

Gefen

Gefen 1x8 DVI DA Manual de usuario

Gefen

Gefen EXT-HDMI1.3-1410-BLK Manual de usuario

Gefen

Gefen AUD-148 Manual de usuario

Gefen

Gefen 1x8 HDTV DA Manual de usuario

Gefen

Gefen HDMI-CAT5-144 Manual de usuario

Gefen

Gefen EXT-VGA-CAT5-148S Manual de usuario

Gefen

Gefen COMPAUD-148 Manual de usuario

Gefen

Gefen EXT COMPAUD 148 Manual de usuario

Gefen

Gefen EXT-UHD600A-44 Manual de usuario

Gefen

Gefen HDMI-142 Manual de usuario

Gefen

Gefen HDMI-144 Manual de usuario

Gefen

Gefen HDMI-1410 Manual de usuario

Gefen

Gefen HDMI-248 Manual de usuario

Gefen

Gefen HDMI1.3-1410 Manual de usuario

Gefen

Gefen AUD-14816 Manual de usuario

Gefen

Gefen EXT-HDMI-144 Manual de usuario

Gefen

Gefen EXT-HDMI-144 Manual de usuario

Gefen

Gefen EXT-AVSCALER-PRO Manual de usuario

Gefen

Gefen Super Booster Plus Manual de usuario

Gefen

Gefen ex tend it VDX 600 Manual de usuario

Gefen

Gefen GTV-VOLCONT-DA Manual de usuario

Gefen

Gefen COMPAUD-CAT5-148 Manual de usuario

Gefen

Gefen DVI-148 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario