GE 11695 Manual de usuario

Universal Remote

Instruction Manual

Control Remoto Universal

Manual de Instrucciones

7252

11695

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

Introduction

Congratulations on your purchase of the GE Universal

Remote. This remote is capable of operating

thousands of audio/video devices including TVs, DVD

players, cable, satellite receivers and more!

IMPORTANT: SAVE THIS MANUAL AND CODE LIST

FOR FUTURE REFERENCE

Introduction..................................................................................... 2

Setup .................................................................................................. 3

Button Functions .......................................................................... 4

Programming Your Remote..................................................... 6

Direct Code Entry................................................................... 6

Auto Code Search ................................................................. 8

Controlling Combo Devices.............................................. 9

Using Your Remote ....................................................................10

Master Volume Feature....................................................10

Reset to Factory Settings.................................................11

Troubleshooting..........................................................................12

Warranty ........................................................................................13

FCC Statement.............................................................................14

Table of Contents

Scan this to view

remote setup video

Mira a ver el video de

instalación remota

http://www.jascoproducts.com/remote

Your universal remote requires two (2) AAA batteries

(not included). Alkaline batteries are recommended.

Battery Installation

1. On the back of the remote, pull back on the tab

and lift the cover off.

2. Match the (+) and (-) marks on the batteries to the

(+) and (-) marks inside the battery compartment,

then insert two (2) AAA batteries. Be sure to use

fresh batteries.

3. Press the battery cover back into place.

NOTE: If your remote stops operating properly,

replace the batteries with new ones. The remote will

retain the codes you have programmed for up to 10

minutes after the batteries are removed.

Battery Precautions

• Donotmixoldandnewbatteries.

• Donotmixalkaline,standard(carbon-zinc),or

rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

• Alwaysremoveold,weakorworn-outbatteries

promptly and recycle or dispose of them in

accordance with local and national regulations.

• Removebatteriesifproductistobeunusedforan

extendedperiodoftime.

Battery Saver

Your remote automatically turns off if the buttons are

depressed more than 8 seconds. This will save your

batteries should your remote get stuck in a place

where the buttons remain depressed (e.g., between

the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote. If

buttons are pressed without batteries in the remote,

all codes will be lost.

Setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

DOT (•) Used

to select digital

channels, e.g., 2.3.

Button Functions

VOLUME UP/DOWN

Changes the volume

level of the device,

normally the TV.

MUTE Turns off the

TV sound while the

picture remains.

UP, DOWN, LEFT &

RIGHT Navigation

buttons.

REW (rewind), FF (fast

forward), PAUSE

Control buttons that

operate your DVR even

when the remote is set

to operate the TV. Also

operates DVD Scan -/+.

TV, CBL, DVD,

AUX

Selects device

to control.

MENU Displays the

Menu on the TV.

A, B, C, D Uses

A, B, C, D functions on

supported devices

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

EXIT ExitsOn-Screen

Menus.

OK Selects menu

items for the device

you are controlling.

Button Functions, cont.

NUMBERS

Enter numbers

for direct channel

selection. Some

devices require

ENTER to be pressed

after channel

selection.

ON•OFF Turns

devices On or Off.

CHANNEL UP/

DOWN Changes

the channels.

Also controls DVD

CHAPTER +/- track

selection,

SETUP Used to

setup the remote,

and for code

search function.

INFO Displays/selects

on-screen channel

information.

GUIDE Displays

satellite or

cable on-screen

program guide.

(Prev. Ch) Returns

to the previously

selected channel.

INPUT Selects the video

inputs from available

viewing sources.

Programming Your Remote

Your GE universal remote control is designed to

control multiple audio/video devices such as a TV,

DVD, DVR, satellite, cable and audio device using

only one remote. To use this remote, you will need to

program it to control the devices of your choice. There

are two ways to program the remote - direct code

entry or auto code search.

Direct Code Entry (Recommended)

1. Locate the Remote Code List provided.

Find the DEVICE CATEGORY you wish

toprogram(forexampleTV, CBL, DVD,

AUX) and then ﬁnd the BRAND of that

device. Circle all the codes under that

brand.Example:ForaGETV,locatethe

TV code section then circle all of the

GE TV codes.

2. Manually turn on the device you wish

to control.

3. Press and hold the SETUP button

until the red indicator light stays on

(approximately2seconds)andthen

release the SETUP button.

4. Press and release the device button on

the remote (TV, CBL, DVD, AUX). The

red indicator will blink once and then

remain on.

5. Enter the ﬁrst 4-digit code previously

found in the code list using the

number buttons on the remote. If the

code entered is a valid code, the red

indicator light will turn off. If the code

entered is not a valid code, the red

indicator light will ﬂash and remain on

allowing you to re-enter the code.

Note: If no buttons are pressed for 35

seconds, the remote will exit the SETUP

mode and you will have to start over.

6. Point the remote at the device. Press

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

Programming Your Remote, cont.

the POWER button—if the device

turns off, no further programming is

required for that device. If the device

does not turn off, return to step 3-5

andusethenextcodefoundinthe

code list. Continue this process until a

code for your device is found.

7. Repeat this process for each device

(forexampleTV,DVD,CBL,SAT,DVR,

AUX) in your home entertainment

system you wish to control.

Programming Notes

• Ifyourdevicedoesnotrespondtotheremoteafter

trying all codes listed or your brand is not listed in

the code list, use the Auto Code Search method to

program your remote.

• Sometimestherstcodethat“works”withyour

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Try other codes

from the code list for more functionality.

• WiththeDirectCodeEntrymethod,youcan

program any device button to control any device

in your home entertainment system.

Forexample,youcanusetheAUX device button

to control an audio receiver or a DVD, VCR, satellite

device, etc.

• Forcombinationdevices,youmayhavetoentera

codeforeachdevice.Forexample,foraVCR/DVD

device, you may have to enter a code for the DVD

under the DVD button and enter a code for the

VCR using a different device button on the remote.

• Writedownthecodefoundtooperateyourdevice

for future reference.

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

Programming Your Remote, cont.

Auto Code Search

The Auto Code Search, searches automatically

through all of the codes stored in this remote. Read

all the steps prior to starting the auto code search

as you will need to be prepared to lock-in the proper

code when found.

1. Manually turn on the device you wish

to control.

2. Press and hold the SETUP button

until the red indicator light stays on

(approximately2seconds)andthen

release the button.

3. Press and release the device button

on the remote (TV, CBL, DVD, AUX) the

type of device you wish to control. The

red indicator will blink once and then

remain on.

4. Point the remote at the device and

press and release the POWER button

(for TV) or PLAY button (for DVD, VCR,

etc.) to start the search. The red

indicatorwillash(approximately

every 2 seconds) as the remote

searches. Note: The remote must be

pointed at the device for the duration of

this search.

5. Place your ﬁnger on the #1 button so

you are prepared to lock-in the code.

6. When the device shuts off or begins

playing, press the #1 button to lock-in

the code. The red indicator light will

turn off. Note: You have approximately

two seconds after the device shuts off

or begins playing to lock-in the code.

7. Point the remote at the device and

check to see if the remote operates the

device as desired. If it does, no further

programming is required for that

device. If it does not, return to step 2

and start the auto code

search again.

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

Programming Your Remote, cont.

8. Repeatthisprocessforeachdevice(forexample

TV, DVD, SAT, AUX) in your home entertainment

system you wish to control.

Programming Notes

• Thisprocessmaytakeseveralminutesasthe

remote contains many codes.

• WhenusingtheAutoCodeSearchprogramming

method, the device button corresponding to

the type of device you want to control must be

selected(forexample,theTV device button must

be selected in step 3 if you want to control a TV,

the DVD device button for a DVD player, etc.)

• TheSETUP button can be used during the search

process to reverse the direction of the search of

theremotecodes.Forexample,ifyoumissthe

code for your device and the remote is continuing

to search (as indicated by the blinking red light),

press the SETUP button and the code search will

reverse direction and return to the code.

• Sometimestherstcodethat“works”withyour

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Continue the

auto code search as directed above until the best

code is found.

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/

VCR, etc.) will require you to set up two different Mode

buttons to control both parts of the Combo device.

Forexample,ifyouhaveaTV/DVDCombo,youmight

need to set up one code under the TV button to

control the TV part AND a separate code (under any

other Mode button) to control the DVD part.

Using Your Remote

Master Volume Feature

The Master Volume Feature allows you to select a

single device (TV or audio receiver) that the volume

controlalwayscontrols.Forexample,theremotecan

be in TV mode while the volume buttons control the

volume on your audio receiver instead of your TV.

Enabling the Master Volume Feature

1. Press and hold the SETUP button

until the red indicator stays on

(approximately2seconds)andthen

release the button.

2. Press and release desired device

button (TV, CBL, DVD, AUX) for the

device you wish to setup to always

control the volume.

3. Press and release the MUTE button.

4. Press and release the VOL + button.

The red indicator will blink twice and

then go off.

To test the feature put the remote in

another mode such as the TV mode if

you programmed the audio receiver to

be the Master Volume Device. Point the

remote at the audio receiver, press and

hold either the VOL - or the VOL + button.

If the audio receiver volume changes then

the remote is programmed correctly. If

the TV volume changes and not the audio

receiver, you will have to repeat the steps

above and test again.

Disabling the Master Volume Feature

1. Press and hold the SETUP button

until the red indicator stays on

(approximately2seconds)andthen

release the button.

2. Press and release the device

button (TV, CBL, DVD, AUX) which is

programmed to control the Master

Volume Feature.

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

input

cbl

aux

dvd

list

exit

setup

Tabla de contenidos

Idiomas:

Manuales populares de Control remoto universal de otras marcas

Pronto

Pronto Peel Manual de usuario

Radio Shack

Radio Shack Wireless Remote Control System Manual de usuario

AUVIO

AUVIO Universal Home Theater Remote Manual de usuario

Philips

Philips Icon SRU4106 Manual de usuario

THOMSON

THOMSON ROC4309 Manual de usuario

Philips

Philips pm625S Manual de usuario

RCA

RCA RCU600WMS - Universal Remote Control Manual de usuario

Blackweb

Blackweb BWB17AV002 Manual de usuario

Marmitek

Marmitek DoorGuard 300 Manual de usuario

Chunghop

Chunghop RM-L618 Manual de usuario

Anderic

Anderic KTN828 Manual de usuario

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manual de usuario

Medion

Medion E74023 Manual de usuario

intensity

intensity RM02A Manual de usuario

Sky

Sky MY Manual de usuario

RCA

RCA RCU600M - Universal Remote Control Manual de usuario

Savant

Savant SUR-0500 Guía de referencia rápida

GDI

GDI GDI-WT2K Manual de usuario