GE 15164 Manual de usuario

Quick Start Guide

Commonly Used Tools

- Phillips Head Screwdriver

- Flat Head Screwdriver

- Hammer

- Wire Cutter/Stripper

WARNING

• Recommended installation by licensed electrician.

• High Voltage (There may be more that one source of supply)

disconnect all power sources before servicing.

• Risk of electric shock – All terminals are live.

• Use copper wire only.

• Close the cover after setting.

• Tighten connections to 25 lbf-in.

• Use correct gauge wire (8-14 AWG) based on local electrical code

of at least 105C rating.

• Approved for outdoor use.

• Wire strip length ½”

• GROUNDING: National Electrical Code requires that grounding must be

continuous and in proper electrical contact in all grounding conductors,

metallic conduits and grounding terminals.

MIN. COPPER WIRE

SIZE (AWG)

MAX LOAD

(AMP)

MINIMUM INSULATION

TEMP (°C)

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

14 15 60

12 20 60

10 30 60

8 40 105

USE CORRECT GAUGE WIRE PER LOCAL ELECTRICAL CODE

Supplied Hardware

- #10 Screw (3)

- #10 Drywall Anchors

Knockouts

Each metal box comes with ½ ” and ¾” knockouts. Follow the pictures below to

remove knockouts.

For ½” knockout place small blade screw driver as pictured above. Tap lightly to

punch knockout loose.

For ¾” knockout ﬁrst use screwdriver to punchout ½” knockout then use pliers

to remove outer ring.

Final result of ¾” knockout

Mounting the timer

1. Select the location for the timer and use the three holes provided for

mounting.

Mounting holes

2. Remove module from timer box. Hold the timer box in place and mark the

holes on the mounting surface.

3. If mounting to drywall:

a. Drill a 3/16” size hole for the drywall anchors at the marked locations

b. Insert an anchor in each hole gently tap the open end of anchor with a

hammer until the anchor is almost ﬂush with the wall.

c. Mount the timer to the anchors using the supplied screws.

4. If mounting to plywood drill a 3/32” size hole for each screw and mount the

timer to the surface using the supplied screws.

240 VAC Setup: Timer Motor & Load same voltage

Connections:

L- Line Input to Timer Motor and Switch 1

1-Line Input to Timer Motor and Switch 2

X-Line Output of time Switch 1

2-Line Output of Time Switch 2

WARNING

• Recommended installation by licensed electrician.

• High Voltage (There may be more that one source of supply)

disconnect all power sources before servicing.

• Risk of electric shock – All terminals are live.

• Use copper wire only.

• Close the cover after setting.

• Tighten connections to 25 lbf-in.

• Use correct gauge wire (8-14 AWG) based on local electrical code

of at least 105C rating.

• Approved for outdoor use.

• Wire strip length ½”

• GROUNDING: National Electrical Code requires that grounding must be

continuous and in proper electrical contact in all grounding conductors,

metallic conduits and grounding terminals.

2XL

LOAD

Typical for same voltage in LOAD and MOTOR

GROUND

L X1 2

Step 1: Remove Plastic Guard

Remove screws using a Philips Head

screwdriver and keep them to the side.

Carefully remove plastic guard and

also keep to the side.

Step 2: Connect the Input/Clock Motor Voltage

1. Connect 240VAC Line 1

(Black) input to

Terminal L.

2. Connect 240VAC Line 2

(Black) input to

Terminal 1.

3. Connect the bare wire

to the ground lug.

Tighten the screw

terminals to 25in-lb.

Improper tightening can

cause heating and

equipment failure.

Step 3: Complete the circuit to the load

1. Connect 240VAC Line 1

(Black) of Load to

Terminal L.

2. Connect 240VAC Line 2

(Black) of Load to

Terminal 1.

3. Connect the bare wire

to the ground lug.

Tighten the screw

terminals to 25in-lb.

Improper tightening can

cause heating and

equipment failure.

Step 4: Reinstall the Plastic Guard

Install both screws with the plastic

guard facing the original position.

Step 5: Activate Timer

1. Turn the mechanism dial counter

clockwise to set the current time as

accurately as possible.

2. After wiring and setting the timer

with the ON/OFF trippers in the

correct timer positions. Be sure to

depress the ON or OFF lever to set

the timer to the desired state. The

timer will turn ON or OFF at the next

programmed time.

3. You cannot see the dial turning.

Wait at least 30 minutes after the

set ON or OFF time to verify the

timer is operating properly.

Step 6: Check timer after 24 hours

1. After 24 Hours, remove power from the timer and check the connections:

a. Remove plastic guard

b. Verify all screws and connections are still ﬁrmly tightened.

c. It is possible that after your initial tightening, the wire has compressed and

loosened the connections.

2. After making sure everything is still tight, replace the plastic guard and

restore power to the timer.

*Please review “Operating Instructions” in the user manual.

Special Note for Plastic Guard

on the back of the motor

On the back of the motor there is a

plastic guard for “Input” side

connections. It snaps easily in and out

of place. If the guard has come off

during shipment or installation,

reinstall by placing the two tabs at the

bottom in the appropriate slots.

15164 VERSION 1

04/18/12

WWW.JASCOPRODUCTS.COM

Plastic guard ﬁtted correctly

Pictured is plastic guard

Ends ﬁt into these holes

Tabla de contenidos

Otros manuales de Minutero de GE

Manuales populares de Minutero de otras marcas

Intermatic

Intermatic P1131 Manual de usuario

Learning Resources

Learning Resources Time Tracker mini Manual de usuario

CEBEK

CEBEK I-215 Manual de usuario

Somogyi

Somogyi home TS MD 5 Manual de usuario

Profile

Profile 010200280 Manual de usuario

Gizmo

Gizmo T4 Manual de usuario

Tekmar

Tekmar Timer 031 Manual de usuario

Daikin

Daikin DST301B61 Manual de usuario

sisel

sisel ENDA ETM2432 Manual de usuario

B&Q

B&Q TE103 Manual de operación y mantenimiento

Hozelock

Hozelock AC Plus 2700 Manual de usuario

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Manual de usuario

Tork

Tork TU40 Manual de usuario

Emos

Emos EMT400F Manual de usuario

FarmTek

FarmTek Polaris Manual de usuario

Maximum

Maximum CRONUS Manual de usuario

Uberhaus

Uberhaus TD133B Manual de usuario

Clas Ohlson

Clas Ohlson 31-3766 Manual de usuario