GE RHM 100 Manual de usuario
RHM 100
g
The RHM 100 can measure ow rates up to 720
t/h (26,455 lb/min) with pressures up to 189 bar.
This large sized model is optimal for loading and
unloading applications - manufactured by GE’s
Rheonik mass owmeter experts.
Applications
• Loading of boats, vessels, rail tank wagons
• Highly viscous media (low pressure drop and
excellent performance at low ow conditions)
Features
• Suitable for pressure up to 189 bar
• Flow uncertainty down to 0.15%
• Density uncertainty down to 0.5%
• Repeatability better than 0.05%
• Unique torsion oscillator
• Typical measuring ranges from 300 to 12000 kg/
min
• Minimal ows as low as 200 kg/min
• Heavy duty version available (increased wall
thickness of measuring loops for additional safety)
• Customization possible
Coriolis Mass Flowmeter
for High Flow Applications
• Hazardous Area Approvals (ATEX, CSA, ...)
Advantages
• High ow rates for fast lling, in combination with
high operating pressure
• Torsion oscillator design assures most stable and
basically drift free measurement and increased
signal to noise ratio
• Not sensitive to changes in pressure
• Longest life time and increased safety (low stress
in welds and increased wall thickness against
abrasion)
• No moving parts, practically no maintenance
GE
Measurement & Control
General Dimensions RHM 100
PF0 (parallel, sealless/welded construction with ange
connection)
(*) Flange reduces the maximum allowable pipe pressure by a factor of 0.75
A2 = 1320 mm (51.97 in) H1 = 1505 mm (59.25 in) Terminal box (without cable gland) 125 x 80 x 58 mm (4.92 x 3.15 x 2.28 in)
B2 = 403 mm (15.87 in) H2 = 1735 mm (68.31 in) W = 150 mm (5.91 in)
Weight with 150# anges: approx. 520 kg (1146 lb)
Shipping in wooden crate as per ISPM 15, approx. 220 x 160 x 90 cm (87 x 63 x 36 in), gross weight with 150# anges and RHE 08 transmitter approx. 750 kg (1654 lb)
Finish type of our ANSI anges corresponds to SF (AARH 125 up to 250 μin, Ra 3.2 up to 6.3 μm)
For customization with regard to face to face length and special ttings, please consult your local agent
Pressure Rating RHM 100
The maximum pressure (pmax) of a sensor is determined by its weakest part. The weakest part can be the measuring
loops (pmax indicated below) or the selected anges / ttings (for pmax please see respective standard). For optional
materials like Alloy C22, wall thickness of measuring loops may change by +/- 10%.
pmax of P0 measuring loops, standard
M1 standard material - 1.4571 (316Ti)
OD x WT 114.3 x 4.5 mm (4.5 x 0.177 in)
bar °C psi °F
73 50 1059 122
66 120 957 248
57 210 827 410
pmax of PA measuring loops
M1 standard material - 1.4571 (316Ti)
OD x WT 114.3 x 6 mm (4.5 x 0.236 in)
bar °C psi °F
99 50 1436 122
88 120 1276 248
76 210 1102 410
2
Process Connection Face to face length (L) Order Code
mm in
Standard Flange DIN DN200/PN16 900 35.43 D1
Flange DIN DN200/PN40 900 35.43 D2
Flange ANSI 8" 150# RF/SF 900 35.43 A1
Flange ANSI 8" 300# RF/SF 900 35.43 A2
Flange ANSI 8'' 600# RF/SF (*) 900 35.43 A3
Optional Flange DIN DN200/PN100 (*) 900 35.43 D3
Flange ANSI 8" 900# RF/SF (*) 900 35.43 A4
Flange ANSI 8" 900# RTJ (*) 900 35.43 R3
Flange ANSI 8" 1500# RF/SF (*) 900 35.43 A5
Flange ANSI 8" 1500# RTJ (*) 900 35.43 R4
Flange JIS RF 10k 200A (8") 900 35.43 J1
Flange JIS RF 20k 200A (8") 900 35.43 J2
pmax of P1 measuring loops
M3 optional material - 2.4602 (Alloy C22)
OD x WT 114.3 x 5 mm (4.5 x 0.197 in)
bar °C psi °F
113 50 1639 122
100 120 1450 248
85 210 1233 410
pmax of PA measuring loops
62 optional material - 1.4462 (Duplex)
OD x WT 114.3 x 6.02 mm (4.5 x 0.237 in)
bar °C psi °F
189 50 2741 122
166 120 2408 248
145 210 2103 410
Performance RHM 100
Max Flow Rate Qmax = 12,000 kg/min (26,455 lb/min) and Qnom (*) = 10,000 kg/min (22,046 lb/min)
Standard Models
Flow Rate Uncertainty
kg/min lb/min in % of reading
12000 26455 0.20
6000 13228 0.20
3000 6614 0.20
800 1764 0.20
300 661 0.50
Goldline Models (**) - selected sensors
Flow Rate Uncertainty
kg/min lb/min in % of reading
9000 19842 0.15
7000 15432 0.15
5000 11023 0.15
3000 6614 0.15
1800 3968 0.15
Low Flow Models (**) - selected sensors
Flow Rate Uncertainty
kg/min lb/min in % of reading
12000 26455 0.20
6000 13228 0.20
800 1764 0.20
300 661 0.50
200 441 0.60
Uncertainty % DP (bar)
Flow Rate kg/min
Uncertainty % DP (bar)
Flow Rate kg/min
Uncertainty % DP (bar)
Repeatability
Better ± 0.1% of rate,
Goldline 0.05%
Density
Down to 0.5% uncertainty
Temperature
Better ± 1°C
Flow Rate kg/min
(*) Nominal ow Qnom refers to roughly 8 - 10 m/s
(26 - 33 ft/s) velocity in measuring loops for best
performance.
(**) Selected sensors are only available in combination
with temperature options T1, TA, standard material and
pressure range.
• Uncertainty of reading (incl. zero drift) indications refer
to reference conditions H2O, 18-24°C (66 - 76°F), 1 - 3
bar (15 – 45 psi) and installation according to eld
manual.
• Calibration at factory only up to 11,000 kg/min.
• Pressure drop indications refer to H2O, with measuring
loops type P0.
• For calibration to customer range and / or with
improved uncertainty, please consult your local
agent.
920-504A
© 2013 General Electric Company. All Rights Reserved. Specications are subject to change without notice. GE is a registered trademark of General Electric Company. Other company or product
names mentioned in this document may be trademarks or registered trademarks of their respective companies, which are not aliated with GE.
gwww.ge-mcs.com
Sensor Size
Temperature Range
T1 NT from -20°C to +120°C (standard)
TA ET from -45°C to +120°C
T2 ET2 Extended Temperature Range from -45°C to +210°C, maximum operating temperature is +150°C
T3 ET1 Extended Temperature Range from -196°C to +50°C
Pressure Range of Measuring Loops @ 120°C and M1 material
P0 pmax = 66 bar (standard)
PA pmax = 88 bar
Construction Type
PF0 Parallel Measuring Loops Seal Less Version
Material of Wetted Parts
M1 Measuring Loops and Connection Part 1.4571 (316Ti) (standard)
62 Measuring Loops and Connection Part 1.4462 (Duplex)
M3 Measuring Loops and Connection Part 2.4602 (Alloy C22)
Process Connection
D1 Flange DIN DN200/PN16 Form C (EN 1092-1 Form B1)
D2 Flange DIN DN200/PN40 Form C (EN 1092-1 Form B1)
A1 Flange ANSI 8” 150# RF/SF
A2 Flange ANSI 8” 300# RF/SF
A3 Flange ANSI 8” 600# RF/SF
Others on request
RHM 100 - - - -
Basic Order Code RHM 100
Temperature Range
• NT Models from -20 to +120°C (-4 to +248°F)
• ET Models from -45 to +120°C (-49 to +248°F)
• ET2 Models from -45 to +210°C (-49 to +410°F)
• ET1 Models from -196 to +50°C (-320 to +122°F)
(Heating for housing optional, please consult your local
agent)
Electrical Connection
• Junction box aluminum coated (standard). Junction box
in SS 316Ti optional
• Cable entry M25 x 1.5. Optional cable entries M20 x 1.5,
1/2” NPT or 3/4” NPT
• Max cable length between RHM and RHE is 30 m (98 ft.).
Optional 100 m (328 ft.) with special cable
Material of Wetted Parts
• 1.4571 / SS 316 Ti / UNS S31635 (standard)
• 2.4602 / Alloy C22 / UNS N06022
• 1.4462 / Duplex / UNS S31803
• Others on request
Sensor Enclosure/Housing
• Stainless Steel 1.4301 / SS 304, optional in 1.4571 / SS
316Ti. Others on request
• Protection Class IP 65. Optional IP 66 / NEMA 4x
Approvals
• ATEX Ex II 1 G, EEx ia IIC T6-T1
• CSA USA-Canada, Class I, Div. 1, Groups A, B, C, D
• PED according to directive 97/23/EC: Module B + C1
• Others on request
General Specications RHM 100
Tabla de contenidos
Otros manuales de Instrumento de medición de GE
GE
GE DINAMAP ProCare Manual de usuario
GE
GE Multilin DDFR Manual de usuario
GE
GE Bently Nevada 3300/16 Manual de usuario
GE
GE DigitalFlow DF968 Manual de usuario
GE
GE Phasor CV Manual de usuario
GE
GE DigitalFlow GF868 Manual del propietario
GE
GE EPM 5300 Manual de usuario
GE
GE Multilin EPM 2200 Manual de usuario
GE
GE CB Watch 3 Manual de usuario
GE
GE Corometrics 170 Series Manual de usuario
GE
GE DigitalFlow GC868 Manual del propietario
GE
GE Protimeter Timbermaster Manual de usuario
GE
GE Moisture monitor series 3 Manual del propietario
GE
GE DigitalFlow GS868 Guía del usuario
GE
GE Transport PT878 Manual de usuario
GE
GE Centricity SP1001 Manual de usuario
GE
GE Multilin EPM 6010 Manual de usuario
GE
GE DMS Go Manual de usuario
GE
GE StressTel T-MIKE E Manual de usuario
GE
GE Dresser Series B3 Manual del propietario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario