GE D20 ME Manual de usuario

gGE Power Systems

D20 ME

Quick Start Guide

Document Number : 994-0025

Version : 1.00

Revision : 8

Date : 03.11.24

Classification: General Full Release

GE Power Systems

D20 ME

Quick Start Guide

NOTICE OF COPYRIGHT & PROPRIETARY RIGHTS

The contents of this manual are the property of General Electric Canada Inc. No part of this work may be reproduced or transmitted in any form

or by any means, except as permitted in written license agreement with General Electric Canada Inc. The information contained in this document

is subject to change without notice.

Any attached hardware schematics and technical descriptions, or software listings that disclose source code, are for information purposes only.

Reproduction in whole or in part to create working hardware or software for other than General Electric Canada Inc. products is strictly

prohibited, except as permitted by written license agreement with General Electric Canada Inc.

TRADEMARK NOTICES

GE and gare trademarks and service marks of General Electric Company.

WESDAC is a registered trademark of General Electric Company, General Electric Canada Inc. All other brand and product names mentioned

in this document are trademarks or registered trademarks of their respective companies.

Important

The circuit boards in the D20 contain many electrostatically sensitive

electronic components.

To prevent damage when handling these products use approved static

control procedures.

994-0025-1.00-8 General

2 Full Release

D20 ME

Quick Start Guide GE Power Systems

D20 ME - Quick Start Guide Contents

Topic See Page

D20 ME Jumper Options 4

Introduction to Downloading Flash Code 7

Code Download – D20 ME - D20 Base 9

Code Download – D20 ME - CCU 11

994-0025-1.00-8 General

3 Full Release

GE Power Systems

D20 ME

Quick Start Guide

D20 ME Jumper Options

D20 ME Board

Layout This diagram shows the location of some of the optional jumpers and

components found on the D20 ME cards (Part # 526-2004 and 526-2005).

JP1

JP3

BootROM

JP2

JP4 JP8

994-0025-1.00-8 General

4 Full Release

D20 ME

Quick Start Guide GE Power Systems

D20 ME Jumper Options, Continued

Table: VME

Jumper

Options

The following tables summarize the jumper settings for each board function

and position that is installed in a CCU for D20 or D200:

Single Node For D20 or D200:

Board Function JP1

Master /

Slave

JP2

VME Address Bits

4 3 2 1

JP3-1

RTC -

SERCLOCK

JP3-2

RTC -

BRTC

Single Node OUT IN IN IN IN OUT IN

Multi-Node For D20 or D200:

Board Function JP1

Master /

Slave

JP2

VME Address Bits

4 3 2 1

JP3-1

RTC -

SERCLOCK

JP3-2

RTC -

BRTC

Node #1 OUT IN IN IN OUT IN IN

Node #2 IN IN IN OUT IN IN OUT

Node #3 IN IN IN OUT OUT IN OUT

Node #4 IN IN OUT IN IN IN OUT

Node #5 IN IN OUT IN OUT IN OUT

Node #6 IN IN OUT OUT IN IN OUT

Node #7 IN IN OUT OUT OUT IN OUT

Node #8 IN OUT IN IN IN IN OUT

Notes: • Single Node is the factory default configuration

• If you have a single-node implementation with Ethernet or Memory expansion or

both, configure jumpers as Single Node

994-0025-1.00-8 General

5 Full Release

GE Power Systems

D20 ME

Quick Start Guide

D20 ME Jumper Options, Continued

JP1 -

VME Control This jumper sets the Master or Slave function of the board on the VME bus.

Note: Single-node D20 systems are always set to Master.

JP2 -

VME Address JP2 is a group of four jumpers that set the VME bus address of the board. The

address should reflect the board location in a D200 CCU chassis.

Example:The board with address 1 will be the lead node, with nodes 2

through 8 positioned to the right of the lead node.

Note: Single-node D20s are set to address 0 (all jumpers IN).

JP3-1 and

JP3-2

RTC Options

These two jumpers determine the Real-Time Clock (RTC) source for each

D20 ME board in a CCU:

• Single-node D20s and the first, or lead, node of a D200 both use an internal

clock.

• Non-lead nodes of a D200 synchronize the clocks to the clock of the lead node.

Table: JP4 -

Watchdog

Enable/Disable

This two-position jumper enables or disables the hardware Watchdog.

Note: Never leave the Watchdog disabled during normal D20 ME

operation.

Jumper Position Function

pin 1 to 2

(center) Disables the hardware Watchdog.JP4

Pin 1 = SLOWCK

Pin 3 = /WD pin 3 to 2

(center) Enables the hardware Watchdog.

Table: JP8 –

Battery Backup

Enable/Disable

The D20 ME card has two 3.6V Lithium batteries, TADIRANTM TL-2150 or

equivalent, to maintain NVRAM contents in the event of a power failure.

Important: Disconnect the batteries if you are storing the board for extended

periods of time.

Jumper Position Function

pin 1 to 2 Disconnects the batteries from the NVRAM

pin 3 to 2 Connects the batteries to the NVRAM

JP8

pins 4 to 5 Always jumpered

994-0025-1.00-8 General

6 Full Release

D20 ME

Quick Start Guide GE Power Systems

Introduction to Downloading Flash Code

Introduction Before you can put a D20ME module into service, it must have a firmware

application code loaded into memory.

All D20 ME boards use Flash memory to store the application code.

Serial

Download You can load the Flash code file serially into the memory of the D20 ME via

the 68K Monitor using most types of Windows communication software,

such as HyperTerminal.

Table: Identify

the D20 ME

Type

The D20 ME module type is determined by the version of BootROM

installed, which identifies how the module will be used. Because the

download method depends on which BootROM is installed, you need to

determine the type of D20 ME module before downloading the Flash code.

Note: The /xx in the Label column is the software revision number.

Module Type BootROM Label

D20 ME D20 Base SBU0000/xx

D20 ME CCU SBU0001/xx

Prerequisites

for Code

Download

You need the following items to successfully load a Flash code file into a D20

ME module:

• Windows PC with HyperTerminal (or equivalent) communication software

loaded.

• The code file, in the Motorola S-record format, located on a local hard drive. If

the file is located on a network or floppy drive, the download may be

significantly slower.

− This file is typically named: down.shx

• A WESMAINT cable for connecting the PC to the D20 ME WESMAINT serial

port.

• The D20 ME card:

− with the hardware option jumpers set

− installed in a D20 or D200 chassis and ready to power-up.

994-0025-1.00-8 General

7 Full Release

GE Power Systems

D20 ME

Quick Start Guide

Introduction to Downloading Flash Code, Continued

Upgrading

From D20M or

1 MB Flash

D20 ME?

Code files for previous D20M modules are created in a binary format, usually

called PROM.BIN files.

• If you are upgrading a device running a D20M to use a D20 ME, you must

convert the binary code file to a down.shx format before you can download it to

Flash memory.

• You must also use Config Pro to adjust the device’s Device Properties so that

the new processor will run the converted code file.

If you are upgrading from a D20 ME with 1 MB Flash (Part # 526-2003), you

must modify the Device Properties of the new configuration in ConfigPro to

use the existing code file.

For more information on upgrading from earlier versions, refer to the D20

ME Processor Module Installation and Operations Guide.

Procedure:

Setup To set up the equipment for downloading code files to the D20 ME:

Step Action

Configure and Connect PC to D20 ME

1 Connect a WESMAINT cable from the PC’s COM port to the D20

ME’s front panel WESMAINT serial port.

2 Start Windows’ HyperTerminal communication software on the

PC, and configure it as follows:

− 9600 Bps

− 8 bit

− no parity

− VT100 emulation

− Xon/Xoff flow control enabled

Identify the D20 ME Type

3 If you already know the D20 ME BootROM “type”, proceed to:

• Code Download – D20 ME - D20 Base or

• Code Download – D20 ME - CCU.

Restart the D20 ME (power off-on cycle) and watch the monitor.

If the first line of output text is: The D20 ME type is:

P149-0, D20 ME BootROM D20 Base

P130-0, GE Energy Services CCUME

BootROM CCU

994-0025-1.00-8 General

8 Full Release

D20 ME

Quick Start Guide GE Power Systems

Code Download – D20 ME - D20 Base

Procedure:

D20 ME - D20

Base

The following steps demonstrate the serial download of a Flash code file to a

D20 Base type of D20 ME module using the 68K Monitor.

Step Action

D20 ME - D20 Base Code Download

1 Restart the D20 ME, again.

2 As soon as messages display on the monitor, press the ESCAPE key

within 5 seconds.

Result: A message displays, asking if you wish to mark the

configuration as “bad”.

3 To proceed with the download, type y.

Result: The current configuration file is overwritten with a

default configuration. The 68K Monitor is initiated.

4 Press ENTER. In the login dialog, type westronic and press ENTER,

then type rd and press ENTER.

Result: After a Welcome message, the D20M> prompt displays.

5 Type sp to suspend all processes running on the D20 ME.

6 Type erase to clear the Flash. This will take several seconds.

Result: Flash Erased is displayed when completed.

Optional Step 1: To speed-up communication to shorten download time

7 Type Baud 38400 and press ENTER (speeds up to 230.4 Kbps, or

lower speeds may be chosen based on ambient EMI, cable length,

PC limits etc.)

Result: The communication speed of the 68K Monitor is set to

38.4 Kbps.

994-0025-1.00-8 General

9 Full Release

GE Power Systems

D20 ME

Quick Start Guide

Code Download – D20 ME - D20 Base, Continued

Procedure: D20 ME - D20 Base (continued)

Step Action

Optional Step 2: To receive feedback during download

8 Configure the HyperTerminal to communicate at the same speed,

and reconnect to the 68K Monitor.

9 If the communication software you are using does not have a

“progress indicator’, you can enable echo to display the code file

on the monitor as it is transferred.

The echo option can be usually found in the Communication

Settings or Properties of the communication program.

Note: Enabling echo may slow the transfer speed.

Download Code File

10 Type dl and press ENTER to ready the D20 ME to receive the

downloadable code file.

11 Click Transfer | Send Text File from menu bar.

Result: A dialog box opens, prompting you to locate the

Down.shx file that you wish to download.

12 Select the correct file, and click Open to start the transfer.

Result: The file transfer may take from less than 10 minutes to

over 30 minutes, depending on the communication speed

selected.

When complete, the D20M> prompt returns.

13 Type el /p to display the error log.

Result: The D20M> prompt should return, indicating no errors

found.

Errors? Record error(s), and re-try download.

If errors persist, contact GE for support.

14 Type el /r to clear the error log, even if there are no errors

displayed in the previous step.

15 Type Boot to restart device.

Result: The D20 ME code download is complete.

994-0025-1.00-8 General

10 Full Release

Otros manuales de Controladores de GE

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario