GE 2-9865 Manual de usuario

®Digital Answerer

2-9865

We bring good things to life.

INTRODUCTION

Your GE digital answerer isdesigned to give you flexibility in use and high quality

performance. Please take a few minutes to read through this instruction manual in

order to get the most from your answerer.

TABLEOFCONTENTS

PARTSCH_'XJJST..................................... 1

INSTALLATION........................................... 2

BATTERYBACKUP..................................... 3

SETUp.................................................... 4

RECORDING THE OUTGOING ANNOUNCEMENT

ADJUSTING THE VOLUME

ANSW_RB_OPERATION.............................. 5

TOLLSAVER ......................................... 6

PLAYINGMESSAGES.............................. 7

ERASINGMESSAGES............................. 8

MEMORYFULL ..................................... 8

TURNING ANSWERER ON AND OFF .......... 9

SCREENING CALLS ................................ 9

REMOTEACCESS................ ,................... 10

REMOTECOVES.................................. 11

GENERALPRODUCTCARE........................ 13

SERVlCE................................................ 13

TROUBLESHOOTINGTIPS .......................... 14

FCC INFORMATION................................. 16

LIMITED WARRANTY...; ............................ 18

WARNING:Yo_w_r R_

TOWORIk_IS_I3RF-

BEFOREYOUBEGIN

PARTSCHECKLIST

Make sure your package includesthe following items:

Telephone llne cord Power adapter

MOI)ULARJAC,KREQUIREMENTS

You need an RJ11 type modular jack, which isthe most com-

mon type of phone jack and might look like the one pictured

here. If you don't have a modular jack, call your local phone

company to find out how to get one installed.

Note: Illustrations contained within this User's Guide are |

for representation only. Your unit may differ slightly. ]

..... ii i _]TI •

Answerer

INSTALLATION

°Plug one end of the telephone line cord into the

jack marked TO WALL OUTLET on the back of the

answerer. Plug the other end into a modular wall

jack.

2. Connect the telephone line cord from your

telephone into the FROM TELEPHONE jack on the

back of the answerer. (You don't have to connect

your telephone in order for the answerer to record

incoming messages.)

3. Connect the small end of the power adapter into

the POWERjack on the back of the answerer. Plug

the other end into an AC power outlet.

Note: Only use the Thomson 5-2399 adapter

that was packed with this unit. Using other

adapters may damage the unit. ]

BATTERY BACKUP

In the event of a power loss, the 9wolt battery

backup enables the answerer to retain messages

stored in memory. To install the battery:

1. Open the battery compartment door on the

bottom of the unit with a screwdriver or

other flat-edged instrument.

2. Connect a fresh 9-volt alkaline battery and

place it inside the battery compartment.

3. Close the battery compartment door.

Note: The BATTERYLOW indicator flashes ]

when you need to change the battery or if ]

you haven't installed the battery.

BAT_RY LOW

indicator

SE'll.TP

RECORV C O rGO G ANNO C

Before using your new answerer, you should recordan outgoing announcement, the

announcement callers hear when your answering system answers a call. If you don't

recordan outgoing announcement, callersjust hear a beep when they call.

When recording the announcement you should be about 6 inches from the unit.

Eliminate as much background noise as possible.

1. Prepare your announcement.

Sample Announcement: Hi, thisis(useyourr_mehere),I can'tae._er thephone_now,so

pleaseleaveyour name, number and a brief message after the tone, and I'll get back to you. Thanks.

2. Hold down the ANNOUNCE button. Recordafter the tone.

3. Release ANNOUNCE button when you finish the announcement.

To review the outgoing announcement, pressand quickly releaseANNOUNCE button.

AVJUST[NG VOLUME

Use the volume control on the side of the answerer to adjust the volume to up or down.

ANSWERER OPERATION

ANNOUNCE

button 0 O0

MESSAGES

indicator light

MESSAGES INDICATOR LIGHT

MESSAGES indicator is on -- Answerer is on and there are no messages.

MESSAGES indicator is flashing -- Number of flashes indicates number of messages.

MESSAGES indicator is off- Answerer is off, but you might still have messages.

MESSAGES indicator is flashing rapidly -- Outgoing announcement isinvalid or memory

isfull.

Tou., SAv_

Yourdigital answering machine will answer a call after 2 rings when there are new

messages and after 5 rings when there aren't any new messages.Toll saver means you

can call your roach(he from another phone to checkmessages, If your machine doesn't

pick up after the second ring, you can hang up and avoid the loft charge.

button

mm _,0. O

V_ -_ -

1- \

PL4_/STOP button

ERASE button

MESSAGES

indicatorliOt

SK_bu_on

PL'. Na

The MESSAGES indicator light flashes when a message has been left onthe answerer.

When the answerer has recorded multiple messages,the MESSAGES indicator light

flashes oncefor each message, pauses, and then repeats.

•Toplay messages: press and release PLAY/STOR

Tostop playback: press and release PLAY/STOP again.

To restart the message that is playing: press and release REVIEW.

To go back to the beginning of a previous message: repeatedly pressand release

REVIEW until you reach the message you want to hear.

Toskip to the beginning of the next message: press and release SKIR

Fast forward: To scan forward through a message, press and hold SKIP.

Review: To scan backward through a message, pressand hold REVIEW.

• To erase a message while it is playing: press and release the ERASEbutton. The

answerer beeps to confirm the message has been erased.

INote: Incoming messages are limited to _ minutes. J

When the answerer isn't playing messages, press and hold ERASE until you hear a

beep. You can retrieve messages erased this way by pressing PLAY/STOP-- but only if

you haven't used any other answerer functions after erasing the messages.

Note: If you hear several high-pitched beeps, your answerer has not erased the ]

messages because some of them or all of them have not been played. J

M ogY

When the memory isfull, the MESSAGES indicator flashes rapidly and the unit

answers after 10 rings. When calling your machine from another phone (called Remote

Access. See p. 10),enter the 3-digit security code after you hear the beep and the

messages play automatically. In order for your machine to record new messages, you

must erase some of the messages. You can erase messages remotely by pressing0

while a message is playing.

Tabla de contenidos

Manuales populares de Contestador automático de otras marcas

Radio Shack

Radio Shack TAD-795 Manual de usuario

AT&T

AT&T 2455 Manual de usuario

Panasonic

Panasonic KX-TG2583CB Manual de usuario

Panasonic

Panasonic KX-TGE820E Manual de usuario

BellSouth

BellSouth GH9488 Guía de seguridad

Panasonic

Panasonic KX-TG2631 Manual de usuario

Panasonic

Panasonic KX-TCD961CXB Manual de usuario

Krown

Krown PortaPrinter 2000STD Manual de usuario

AT&T

AT&T 1717 Manual de usuario

Alcatel

Alcatel TEMPORIS 55-CE Manual de usuario

AT&T

AT&T E2562 Manual de usuario

Telstra

Telstra Monitor 420 Manual de usuario

Kortex

Kortex IAM V90 Manual de usuario

Panasonic

Panasonic EASA-PHONE KX-T1451 Manual de usuario

Philips

Philips VOIP8551B/05 Manual de usuario

Topcom

Topcom LUCCA Answering Machine Manual de usuario

Panasonic

Panasonic KX-TGM420 Manual de usuario

Panasonic

Panasonic KX-TCD320E Manual de usuario