GCX 7000-MS3 Manual de usuario
DU-CAP-0002-67 Rev A 2/16/16 GCX Corp Page 1 of 3
Item # Description Qty.
1
1
2
1
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com
Installation
Guide
Roll Stand Post Mount for 75mm VESA Data Capture Devices on Welch Allyn
7000-MS3 Roll Stand
(Refer to qualified
personnel)
Purpose: To describe installation of Post Mounting Assembly to Welch Allyn Roll Stand
The purpose of this manual is to describe general installation of Post Mounting Assembly to Welch Allyn
Roll Stand. This manual should be used in conjunction with any instrument-specific installation guides.
Please read this manual and all instrument-specific installation material before installing or using this
product.
Parts Reference
The following parts and hardware are included in this installation kit:
(Hardware not shown)
Tools Required:
3/16” Hex Wrench (Provided)
5/32 Hex Wrench (Provided)
Phillips Screwdriver (Not Provided)
2X 1/2"/13mm Wrench (Not Provided)
Ensure that the weight of the instrument being mounted does not exceed the load
rating limit of 10lb. Failure to do so may result in damage to equipment or injury.
1
3 3
2
3
Post Mounting Assembly
Cable Clip
Clamping Block
4 10-32 X 5/8 Socket Head Cap Screw 2
5 M4 X 8mm Pan Head Machine Screws 4
DU-CAP-0002-67 Rev A 2/16/16 GCX Corp Page 2 of 3
1 2
4
2X 10-32 x 5/8” SHCS
5/32” Hex Wrench
4X M4 x 8mm PHMS
5 6
Maximum Height 3.25”/8.2cm.
Setting height above this level may
result in damage to equipment or injury
3
Maximum Height 8”/20.32cm.
Setting height above this level may
result in damage to equipment or injury
3/16” Hex Wrench
2X 1/2”/13mm Wrench
DU-CAP-0002-67 Rev A 2/16/16 GCX Corp Page 3 of 3
Routine Maintenance
Periodically inspect all fasteners associated with the mounting assembly. Tighten or Adjust as
necessary for optimal operation and safety.
Cleaning the Mounting Assembly
The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in
the hospital environment (e.g. diluted bleach, ammonia, or alcohol solutions).
The surface finish will be permanently damaged by strong chemicals and solvents such as acetone
or trichloroethylene.
Steel wool or other abrasive material should never be used.
Damaged caused by the use of unapproved substances or processes will not be warranted. We
recommend testing of any cleaning solution on a small area of the mounting assembly that is not
visible to verify compatibility.
Never submerge or allow liquids to enter the mounting assembly. Wipe any cleaning agents off the
mounting assembly immediately using a water-dampened cloth. Dry the assembly thoroughly after
cleaning.
CAUTION: GCX makes no claims regarding the efficacy of the listed chemicals or processes as a
means for controlling infection. Consult your hospital’s infection control officer or epidemiologist. To
clean or sterilize mounted devices or accessory equipment, refer to the specific instructions delivered
with those products.
Tabla de contenidos
Otros manuales de Rack y soporte de GCX
GCX
GCX VHM-P Manual de usuario
GCX
GCX VHM Manual de usuario
GCX
GCX Kaiser NFS Manual de usuario
GCX
GCX PH-0062-01 Manual de usuario
GCX
GCX VHM-P Manual de usuario
GCX
GCX KP-0003-28 Manual de usuario
GCX
GCX Mindray V Series Manual de usuario
GCX
GCX VHM Series Manual de usuario
GCX
GCX M Series Manual de usuario
GCX
GCX FLP-0002-17 Manual de usuario
GCX
GCX FLP-0008-11 Manual de usuario
GCX
GCX MP5 Instrucciones de funcionamiento y mantenimiento
GCX
GCX VHM Series Manual de usuario
GCX
GCX DR-0015-20 Instrucciones de instalación
GCX
GCX M Series Manual de usuario
GCX
GCX VHM Series Manual de usuario
GCX
GCX LiDCO Manual de usuario
GCX
GCX Variable Height Roll Stand with Storage Bay Manual de usuario
GCX
GCX RS-0006-64 Manual de usuario
GCX
GCX AG-0019-07 Manual de usuario
