GBC FOTON 30 Automated Laminator Manual de usuario

any form or by any means without prior written permission of ACCO Brands. GBC® and Foton™30 are

registered trademarks of ACCO Brands Corporation.

Trouble Shooting Guide V1.0

TROUBLE SHOOTING

SYMPTON

POSSIBLE CAUSE

CORRECTIVE ACTION

Pressing the Power

button does not

turn the machine

The power cord may not

be inserted all the way

into outlet

Fully Insert plug into outlet

Make sure the outlet has power

Status Indicator

Red:

Door Error Indicator Red:

Paper Jam Error Indicator

Red:

Film Empty Indicator Red:

Cutter Error Indicator Red

Remove any paper from the feeder tray. Open and Close both the

laminator door and the feeder door. Ensure they are fully closed

Open the feeder door, and remove any paper from the feeder tray.

Close the feeder door.

If the above does not clear the error, press and hold the RUN button for

10 seconds to manually feed film. Film should begin to exit the machine

and Jam should clear.

If Jam error remains, open laminator door and look to see if film leader

is caught on an obstacle or the rollers. DO NOT CUT the film. Lift-up the

film leader and replace it in proper position. Shut Laminator door and

hold the run button for 10 Seconds.

Cartridge End of Roll label has been detected. Replace the film cartridge

with new cartridge and shut the laminator door.

The cutter could not initiate a cut, or did not finish a cut.

Press the manual cut button one time to try and activate the cutter. Not

resolved, try the following:

Observe the film at the exit of the laminator to see if the film is not cut

or partially cut.

Film is not cut:

Press and hold the RUN button for about 10-20 seconds to

manually advance the film. If there is laminated media in the

exit of the laminator, hold the RUN button until the media has

fully exited the laminator. Now press the manual cut button to

see if the cutter is activated.

Film is Partially Cut:

Open the laminator door and look to see if you can see the

trimmer blade. It will be near the back of the laminator

partway through the film. Using scissors cut the film hanging

out the exit of the laminator. Then using caution not to put

your fingers near the trimmer knife, carefully remove the

cartridge. Close the laminator door and try to manually cycle

any form or by any means without prior written permission of ACCO Brands. GBC® and Foton™30 are

registered trademarks of ACCO Brands Corporation.

Status Indicator

Red Continued:

Cutter Error Indicator Red

Continued:

the cutter. If the cutter works Re-insert your cartridge. Might

need to trim off the leading edge of film where the cutter

jammed. If you need to trim the film leave 4 inches (100mm)

of sealed film as the cartridge leader. Re-insert the cartridge.

The machine once warmed-up will automatically thread the

film and activate the trimmer.

If the cutter does not work after the above steps contact GBC customer

service for warranty repair.

Film Wrinkles on

output

Film Misaligned

Press and hold the RUN button to manually advance the film. After 5 –

20 inches (125 –500mm) of film has been advanced the wrinkle should

work themselves out. If wrinkle clear press the manual cut button and

you are ready to begin.

If wrinkles still present, open the laminator door. Grasp the film exiting

the laminator and hold it Taut while closing the laminator door. Repeat

above step and wrinkles should disappear.

Film Edges are not

evenly aligned.

Top and bottom rolls of

film are not matched

properly.

Press and hold the RUN button to manually advance the film. After 5

inches (125 mm). Grasp the film exiting the laminator and hold it Taut

while closing the laminator door.

Documents are

skewed in the film

when exiting

Documents fed in skewed

Before loading paper, try tapping the leading edge of the paper on a flat

surface and then repeat with the bottom or top edge to get your paper

properly squared.

Insert your media in the auto feeder and slide the edge guide up to edge

of your media.

Experiencing

frequent double

feeds

Paper has heavy static

Try fanning the media or placing in a paper jogger prior to feeding it. If

issues persist use the Manual Feed / Auto Cut mode.

Experiencing

frequent mis-feeds

Rollers are slipping on

media and do not feed

sheets

Try fanning the media or placing in a paper jogger prior to feeding it. If

issues persist use the Manual Feed / Auto Cut mode.

Otros manuales para FOTON 30 Automated Laminator

Otros manuales de Laminadora de GBC

GBC

GBC 13 PRO Manual de usuario

GBC

GBC 2064-WF Manual de usuario

GBC

GBC HEATSEAL H800 PRO-R Manual de usuario

GBC

GBC HeatSeal H425 Manual de usuario

GBC

GBC 930-028 Instrucciones de funcionamiento

GBC

GBC 4500 Manual de usuario

GBC

GBC FOTON 30 Automated Laminator Manual de usuario

GBC

GBC Explorer 107 Manual

GBC

GBC OORCA-III Manual de usuario

GBC

GBC 640T Manual de usuario

GBC

GBC Titan 1244WF Instrucciones de instalación

GBC

GBC Laminator Manual de usuario

GBC

GBC HeatSeal H520 Manual de usuario

GBC

GBC Fusion 5000L A3 Manual de usuario

GBC

GBC HeatSeal H65 Manual de usuario

GBC

GBC HeatSeal H210 Manual de usuario

GBC

GBC Pinnacle 27 EzLoad Manual de usuario

GBC

GBC Fusion Plus 7000 L Manual de instrucciones

GBC

GBC FUSION 3000L Manual de usuario

GBC

GBC ORCA-I Manual de usuario

GBC

GBC HeatSeal H215 HighSpeed Manual de usuario

GBC

GBC FALCON 60 C Manual de usuario

GBC

GBC Arctic Titan 1040WFC Manual de usuario

GBC

GBC Discovery 50 Manual de usuario

Manuales populares de Laminadora de otras marcas

Renz

Renz HT 330 L Manual de usuario

Gfp

Gfp 44TH Manual de usuario

Lapis

Lapis Lamina006 Manual de usuario

Hama

Hama L44B Manual de usuario

PAVO

PAVO FLORIDA Manual de usuario

M-Triangel

M-Triangel MT-102 Manual de usuario

Akiles

Akiles PROLAM 230 Manual de usuario

D&K

D&K Masterpiece 550 Manual de usuario

Falcon

Falcon F-40 Manual de usuario

LEITZ

LEITZ EasyLaminator A4 Manual de usuario

LEITZ

LEITZ coldLAM CS9 Manual de usuario

kala

kala Starter 1080 Manual de usuario

Fellowes

Fellowes Venus A3 Manual de usuario

Qomolangma

Qomolangma FMJ-1400-WA-PLUS Manual de usuario

Opus

Opus Coverator 330 Manual de usuario

ALDI

ALDI OL 250-L Manual de usuario

Phoenix

Phoenix 2700-DH Manual de usuario

acropaq

acropaq AL-3400 Manual de usuario