Garmin GPSMAP 2006 Manual de usuario

Otros manuales para GPSMAP 2006

4

Este manual sirve para los siguientes modelos

6

Otros manuales de GPS de Garmin

Garmin

Garmin GPSMAP 66 Manual de usuario

Garmin

Garmin Approach G7 Manual de usuario

Garmin

Garmin GPSMAP 4008 - Marine GPS Receiver Manual de usuario

Garmin

Garmin DriveTrack 70 Manual de usuario

Garmin

Garmin EDGE 830 Manual de usuario

Garmin

Garmin GPSMAP 8000 Series Manual de usuario

Garmin

Garmin GPSMAP 76 series Guía de referencia

Garmin

Garmin GPSMAP 60Cx Manual de usuario

Garmin

Garmin GPSMAP 640 Manual de usuario

Garmin

Garmin Quest 2 Manual de usuario

Garmin

Garmin Zumo 500 Manual de usuario

Garmin

Garmin GPSMAP 78 series Manual de usuario

Garmin

Garmin nuvi 310 Manual de usuario

Garmin

Garmin GPSMAP 60Cx Manual de usuario

Garmin

Garmin Road Tech Zumo 665 Manual de usuario

Garmin

Garmin DĒZL OTR810 Manual de instrucciones

Garmin

Garmin Alpha 100 Manual de usuario

Garmin

Garmin nuvi 500 Series Manual de usuario

Garmin

Garmin iQUE 3600 Manual de usuario

Garmin

Garmin GPSMAP 550 Manual de usuario

Garmin

Garmin Cessna Caravan G1000 Manual de usuario

Garmin

Garmin GPSMAP 76Cx Manual de usuario

Garmin

Garmin 190-00556-10 Manual de usuario

Garmin

Garmin nuvi 140 series Manual de usuario

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario

Kenwood

Kenwood DNN9330BT Manual de usuario

Safelet

Safelet Indra Manual de usuario

Bushnell

Bushnell 360100 Manual de usuario

Geneq

Geneq SXBlue Manual de usuario

ORIGO

ORIGO ED308 Manual de usuario

7.5" (190 mm)

5.91"

(150 mm)

GPSMAP 2006/2006C/2106/2206/3006C/3206

TRIM TEMPLATE ALONG THIS LINE TO AID FITTING

CUT MOUNTING SURFACE

ALONG INSIDE OF THIS LINE.

UNIT OUTLINE

GPSMAP 2x06/2x10/3x06/3x10

FLUSH MOUNT TEMPLATES

Drill a 3/8" (6 mm) hole.

Begin cutting here.

Be very careful when cutting this hole,

because there is only a small amount

of clearance between the unit and the

mounting hole.

To flush mount the GPSMAP 2006/2006C/2106/2206/3006C/3206:

1. Trim the flush mount template and tape it in the preferred location.

2. Using the center punch, indent the center of each mounting hole location.

3. Using an 1/8" (3 mm) drill bit, drill the four mounting holes. (Drilling the mounting

holes before cutting the hole for the unit allows for an easier installation.)

4. Using a 3/8" (6 mm) drill bit, drill a hole to begin cutting the mounting surface.

5. Using the jig saw, cut the mounting surface along the inside of the dashed line

indicated on the template. Be very careful when cutting this hole, because there is only a

small amount of clearance between the case molding and the mounting holes.

6. Install the four mounting studs into unit by screwing the shorter, threaded section

into the back of the unit. Use a .05" Allen wrench to tighten the mounting studs

until the stop contacts the case. Be careful not to overtighten, because this may damage the

mounting stud! The studs have a reusable thread-locking patch pre-applied from the factory.

7. Place the unit into the cut out of the mounting surface.

8. Place washers over the mounting studs, then thread on one hex nut per mounting stud.

Tighten all four until the unit is snug against the mounting surface.

Install and tighten the second hex nut on all four mounting studs to lock the first one

in place.

Garmin International 1200 E. 151st Street, Olathe, KS 66062 190-00243-00 Rev. F April 2006 Printed in Taiwan

9.05" (230 mm)

8.19"

(208 mm)

GPSMAP 2010/2010C/2110/2210/3010C/3210

CUT MOUNTING SURFACE

ALONG INSIDE OF THIS LINE.

UNIT OUTLINE

Drill a 3/8" (6 mm) hole.

Begin cutting here.

TRIM TEMPLATE ALONG THIS LINE TO AID FITTING

Be very careful when cutting this hole,

because there is only a small amount of

clearance between the unit and the

mounting hole. To flush mount the GPSMAP 2010/2010C/2110/2210/3010C/3210:

1. Trim the flush mount template and tape in the preferred location.

2. Using the center punch, indent the center of each mounting hole location.

3. Using an 1/8" (3 mm) drill bit, drill the four mounting holes. (Drilling the mounting

holes before cutting the hole for the unit allows for an easier installation.)

4. Using a 3/8" (6 mm) drill bit, drill a hole to begin cutting the mounting surface.

5. Using the jig saw, cut the mounting surface along the inside of the dashed line

indicated on the template. Be very careful when cutting this hole, because there is only a

small amount of clearance between the case molding and the mounting holes.

6. Install the four mounting studs into unit by screwing the shorter, threaded section

into the back of the unit. Use a .05" Allen wrench to tighten the mounting studs

until the stop contacts the case. Be careful not to overtighten, because this may damage the

mounting stud! The studs have a reusable thread-locking patch pre-applied from the factory.

7. Place the unit into the cut out of the mounting surface.

8. Place washers over the mounting studs, and then thread on one hex nut per mounting stud.

Tighten all four until the unit is snug against the mounting surface.

Install and tighten the second hex nut on all four mounting studs to lock the first one

in place.