Garmin GPS-III+ Manual de uso y cuidado

Tabla de contenidos

Otros manuales de GPS de Garmin

Garmin

Garmin Zumo 395 Manual de instrucciones

Garmin

Garmin Rino 120 Manual de usuario

Garmin

Garmin GPSMAP 496 Manual de usuario

Garmin

Garmin GPSMAP 76Cx Manual de usuario

Garmin

Garmin NUVI 2300 series Manual de instrucciones

Garmin

Garmin Personal Navigator GPS 48 Manual de usuario

Garmin

Garmin GPS 158 Manual de usuario

Garmin

Garmin GPSMAP 66 Manual de usuario

Garmin

Garmin Forerunner 201 - Running GPS Receiver Manual de usuario

Garmin

Garmin Nuvi 205 Series Manual de usuario

Garmin

Garmin GNC 300 Manual

Garmin

Garmin nuvi 1460 Manual de instrucciones

Garmin

Garmin GPSMAP 64SX Manual de usuario

Garmin

Garmin GPS 75 Manual de usuario

Garmin

Garmin GPS 10 Manual de usuario

Garmin

Garmin DRIVETRACK 71 Manual de usuario

Garmin

Garmin GPS 400 Manual de usuario

Garmin

Garmin GPSMAP 296 - Aviation GPS Receiver Manual

Garmin

Garmin GLO 2 Manual de usuario

Garmin

Garmin StreetPilot c550 Manual de usuario

Garmin

Garmin GPSMAP 5215 Manual de usuario

Garmin

Garmin 010-10844-00 - Mobile XT - GPS Software Instrucciones originales

Garmin

Garmin GPSMAP1222 Manual de usuario

Garmin

Garmin GTN 625 Manual

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario

Kenwood

Kenwood DNN9330BT Manual de usuario

Safelet

Safelet Indra Manual de usuario

Bushnell

Bushnell 360100 Manual de usuario

Geneq

Geneq SXBlue Manual de usuario

ORIGO

ORIGO ED308 Manual de usuario

Garmin® GPS-III+ Backup Battery Replacement

If you receive a screen message that your backup battery has lost charge, it is time to

replace it. Here is how.

1. Tools and supplies

a. Japanese JIS Standard “Phillips” head screwdrivers. These drivers are cut

in a different manner and provide a good grip on the screws. You will

mess the screws up if you do not use JIS screwdrivers.

b. De-soldering gun, de-soldering braid or solder sucker.

c. Soldering station with a fine tip

d. Solder

e. Precision sidecutters

f. Battery. Panasonic VL1220-1VC. These are available from

www.mouser.com

1. Replacing the battery. If you do not have the equipment and ability to do fine

soldering do not attempt this project. Please note that removing the backup

battery will delete all waypoints and other stored information.

a. Remove six screws from the back of the case

b. Carefully open the case. There is a connector cable that you can damage

if it suddenly pops open.

c. Using a jeweler’s screwdriver, gently pry up the white cable connector

from the circuit board and set the back of the case aside.

d. Locate the battery. It is on edge next to a capacitor just to the left of the

white connector.

e. Using a jeweler’s screwdriver, pull the plastic clamp back on the brown

ribbon cable to the stops.

f. Remove the screw near the metal can on the antenna end of the board.

g. Gently tip the board up, hinging on the ribbon cable edge. The board will

stick and it will take some leverage to get it up. The ribbon cable will

slide out of the clamp.

h. Turn the board over and locate the battery pads on the back side of the

circuit board and remove the solder.

i. Remove the battery and clean the holes in the pad.

j. Insert the new battery, and check the polarity. The positive side of the

battery should be towards the metal can on the antenna end.

k. Solder the battery leads and trim them.

l. Replace the board in the chassis. Slide the ribbon cable into the clamp, set

the board in place, and install the screw.

m. Replace the white cable clamp

n. Making sure antenna wire is not pinched, reassemble the case and install

the screws.

o. You are done!