Garmin GLO Aviation Manual de usuario

August 2012 190-01492-91_0A Printed in Taiwan

GLO™ GLONASS and GPS Sensor Instructions ��2

Instructions pour le capteur GLONASS et GPS GLO™ ��8

Istruzioni del sensore GLO™ GLONASS e GPS ��14

GLO™-GLONASS- und GPS-Sensor – Anweisungen ��19

Instrucciones del sensor de GPS y GLONASS GLO™ ��25

Instruções do GLO™ GLONASS e do Sensor GPS ��31

Instructies voor GLO™ GLONASS en GPS-sensor ��37

Vejledning til GLO™ GLONASS og GPS-sensor ��42

GLO™- GLONASS- ja GPS-antureiden ohjeet ��48

Instruksjoner for GLO™ GLONASS- og GPS-sensor ��53

GLO™ GLONASS- och GPS-sensorinstruktioner ��58

Instrukcja obsługi czujnika GLO™ GLONASS i GPS �� 63

сплуатации датчика GLO™ для систем ГЛОНАСС и GPS ��69











This product contains a lithium-ion battery.

See page 5 for important battery safety

information.

 With your thumbnail, slide the battery

cover release tab ➊.

➌➊

➋

 Remove the battery cover ➋.

 Locate the metal contacts on the end

of the lithium-ion battery.

 Insert the battery ➌ so the metal

contacts on the battery align with

the metal contacts inside the battery

compartment.

 Press the battery down into place.

 Insert the battery cover into the

notches and press down.

The release tab locks the cover in

place.



You can purchase a replacement battery

(010-10840-00) at http://buy.garmin.com.



You can use the sensor while you are

charging it.

 Plug the small end of the power cable

into the mini-USB connector on the

end of the sensor.

 Plug the other end of the power cable

into an appropriate source of power for

the cable type.

It takes about three hours to charge the

battery. A fully charged battery lasts about

12 hours.

: If the battery has not been charged

for a long period of time, remove the

battery, connect the cable to the device

and a power source, and then replace the

battery. The battery will charge as usual.



 Hold to turn on the sensor.

 Turn on the other device and enable

the Bluetooth component.

You can refer to the device’s

documentation for specic instructions

about enabling Bluetooth wireless

technology.

 Bring the sensor within 30 feet (10

meters) of the mobile device.

 Using the mobile device, pair the

sensor with the mobile device.

The blue LED is solid blue when the

sensor is connected to the other device.

If the sensor has not established a

Bluetooth connection for several minutes,

it turns off automatically.



 

Slow ashing

blue

Searching for mobile devices

Rapid ashing

blue

Pairing

Solid blue Connected to mobile device



 

Slow ashing orange Charging

Solid orange Battery charged,

power connected.

Orange off Battery charged,

power disconnected.

Rapid ashing orange Low battery

Alternating orange

and green

Faulty battery or

system error

Flashing green Searching for GPS

satellites

Solid green GPS satellite x



 Verify that the blue LED on the sensor

is solid blue, indicating a wireless

connection.

 Place the sensor where it has a clear

view of the sky.

Acquiring satellite signals may take a

few minutes. The Status LED ashes

green while searching for satellites and

establishing your location. The Status LED

is solid green when it has established a x

on your location.





The portable friction mount comes in

some GLO packages and is available as

an optional accessory.

 Wipe the mounting surface and the

back of the mount with a wet cloth to

remove dust and debris.

 Insert the sensor in the mount so the

LEDs face up and the mini-USB port is

accessible.

 Place on a at surface.

Periodically, you should wipe the surface

and the mount with a wet cloth to remove

dust and debris to help prevent the mount

from sliding.



Made for iPod® touch (4th generation),

iPod touch (3rd generation), iPhone® 4S,

iPhone 4, iPhone 3GS, iPad® 2, and iPad.

"Made for iPod, iPhone, iPad” means

that an electronic accessory has been

designed to connect specically to iPod,

iPhone, or iPad, respectively, and has

been certied by the developer to meet

Apple performance standards. Apple is

not responsible for the operation of this

device or its compliance with safety and

regulatory standards. Please note that the

use of this accessory with iPod, iPhone, or

iPad may affect wireless performance.

The GLO sensor is also compatible with

many Android®, Windows® or Blackberry®

smartphones, tablets and notebook

computers.

When using the GLO GPS/GLONASS

sensor with an Android device, you

may need to use an application to allow

the sensor to properly communicate

with the Android system over Bluetooth

technology. The application will allow the

Android system to accept non-system (or

mock) GPS/GLONASS signals.



• Go to http://my.garmin.com.

• Keep the original sales receipt, or a

photocopy, in a safe place.



: Rugged, but not water-resistant

: Rechargeable lithium-ion

battery, 12 hours (typical use)

: 10 Hz, but not all mobile

devices support a 10 Hz update rate.

:

12–28 Vdc (*available in some packages)

: -4°F to 140°F

(-20°C to 60°C)

: 32°F to 113°F

(0°C to 45°C)



: -4°F to 122°F (-20°C to

50°C)



: -4°F to 68°F (-20°C to

20°C)











When installing the device in a vehicle,

place the device securely so it does not

obstruct the driver’s view of the road ➊ or

interfere with vehicle operating controls,

such as the steering wheel, foot pedals,

or transmission levers. Do not place

unsecured on the vehicle dashboard

➋. Do not place the device in front of or

above any airbag ➌.

➋

➌

➊



If these guidelines are not followed, the

battery may experience a shortened life

span or may present a risk of damage to

the sensor, re, chemical burn, electrolyte

leak, and/or injury.

• Do not leave the sensor exposed to a

heat source or in a high temperature

location, such as in the sun in an

unattended vehicle. To prevent the

possibility of damage, remove the

device from the vehicle or store it out

of direct sunlight, such as in the glove

box.

• Do not use a sharp object to remove

the battery.

• Do not disassemble, puncture,

incinerate, or damage the battery.

• Keep the battery away from children.

• If using an external battery charger,

only use the Garmin accessory

approved for your product.

• Only replace the battery with the

correct replacement battery. Using

another battery presents a risk of

re or explosion. To purchase a

replacement battery, see your Garmin

dealer or the Garmin website.

• When storing the device for an

extended time, store within the

following temperature range: from -4°F

to 68°F (-20°C to 20°C).

• Do not operate the device outside of

the following temperature range: from

-4°F to 140°F (-20°C to 60°C).

• Contact your local waste disposal

department to dispose of the device/

battery in accordance with applicable

local laws and regulations.



Use this sensor only as a navigational aid.

Do not attempt to use the sensor for any

purpose requiring precise measurement

of direction, distance, location, or

topography. This product should not be

used to determine ground proximity for

aircraft navigation.



Information about Garmin’s product

recycling program and WEEE, RoHS,

REACH, and other compliance programs

can be found at www.garmin.com

/aboutGarmin/environment.



Hereby, Garmin, declares that this

product is in compliance with the

essential requirements and other relevant

provisions of Directive 1999/5/EC. To view

the full Declaration of Conformity, go to

www.garmin.com/compliance.



This device complies with part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference,

and (2) this device must accept any

interference received, including

interference that may cause undesired

operation.

This equipment has been tested and

found to comply with the limits for a

Class B digital device, pursuant to

part 15 of the FCC rules. These limits

are designed to provide reasonable

protection against harmful interference in

a residential installation. This equipment

generates, uses, and can radiate radio

frequency energy and may cause harmful

interference to radio communications if

not installed and used in accordance with

the instructions. However, there is no

guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio

or television reception, which can be

determined by turning the equipment off

and on, the user is encouraged to try to

correct the interference by one of the

following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and the receiver.

• Connect the equipment into an outlet

that is on a different circuit from the

GPS unit.

• Consult the dealer or an experienced

radio/TV technician for help.

This product does not contain any user-

serviceable parts. Repairs should only be

made by an authorized service center.

Unauthorized repairs or modications

could result in permanent damage to the

equipment, and void your warranty and

your authority to operate this device under

Part 15 regulations.



Category I radiocommunication devices

comply with Industry Canada Standard

RSS-210. Category II radiocommunication

devices comply with Industry Canada

Standard RSS-310. This device complies

with Industry Canada license-exempt RSS

standard(s). Operation is subject to the

following two conditions: (1) this device

may not cause interference, and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device.



Garmin’s standard limited warranty applies

to this accessory. For more information,

go to www.garmin.com/support/warranty

.html.













Ce produit contient une batterie lithium-

ion. Reportez-vous à la page 11 pour

consulter les informations importantes sur

la batterie.

 Avec l'ongle du pouce, faites coulisser

le couvercle de la batterie ➊.

➌➊

➋

 Retirez le couvercle de la batterie ➋.

 Localisez les contacts métalliques à

l'extrémité de la batterie lithium-ion.

 Insérez la batterie ➌ de sorte que ses

contacts métalliques soient alignés sur

ceux gurant dans son compartiment.

 Appuyez sur la batterie pour la mettre

en place.

 Insérez le couvercle de la batterie

dans les encoches et appuyez.

La patte de dégagement garde le

couvercle bien en place.



Vous pouvez acheter une batterie de

rechange (010-10840-00) sur http://buy

.garmin.com.



Vous pouvez continuer à utiliser le capteur

pendant le chargement.

 Branchez la petite extrémité du câble

d'alimentation dans le connecteur

mini-USB à l'extrémité du capteur.

 Branchez l'autre extrémité du

câble d'alimentation à une source

d'alimentation adaptée au type de

câble.

Le chargement de la batterie dure environ

trois heures. Une batterie entièrement

chargée a une autonomie d'environ

12 heures.

 : si la batterie n'a pas été

chargée depuis longtemps, retirez la

batterie, branchez le câble à l'appareil et à

une source d'alimentation, puis replacer la

batterie. Le chargement de la batterie se

déroulera normalement.



 Maintenez la touche enfoncée pour

mettre le capteur sous tension.

 Allumez l'autre appareil et activez la

fonction Bluetooth.

Reportez-vous à la documentation de

votre appareil pour savoir comment

procéder pour activer la technologie

sans l Bluetooth.

 Eloignez le capteur à 10 mètres

(30 pieds) de l'appareil portable.

 A l'aide de l'appareil portable, couplez

le capteur à l'appareil portable.

Le voyant bleu devient xe lorsque le

capteur est connecté à l'autre appareil.

Si le capteur ne parvient pas à établir la

connexion Bluetooth au bout de plusieurs

minutes, il s'éteint automatiquement.



 

Bleu - clignotement

lent

Recherche d'un

appareil portable

Bleu - clignotement

rapide

Couplage

Bleu - xe Connecté à un appareil

portable



 

Orange - clignotement

lent

Chargement

Orange - xe Batterie chargée,

branchée à

l'alimentation.

Orange - éteint Batterie chargée,

alimentation coupée.

Orange - clignotement

rapide

Batterie faible

Orange et vert -

alternés

Batterie défectueuse

ou erreur système

Vert - clignotement Recherche des

satellites GPS

Vert - xe Satellites GPS

localisés





 Vériez que le voyant bleu du capteur

est xe, ce qui indique une connexion

sans l.

 Placez le capteur à un endroit offrant

une vue dégagée sur le ciel.

L'acquisition de signaux satellites peut

prendre quelques minutes. Le voyant DEL

d'état vert clignote lors de la recherche

des satellites et de l'établissement de

votre position. Le voyant DEL d'état vert

est xe lorsque la connexion est établie

pour votre position.





Ce support portable antidérapant est

fourni avec certains appareils GLO et peut

être acheté séparément.

 Nettoyez la surface de montage et

l'arrière du support avec un chiffon

humide pour éliminer la poussière et

les saletés.

 Insérez le capteur dans le support : les

voyants doivent se trouver en haut et

le port mini-USB doit rester accessible.

 Placez-le sur une surface plane.

Il est conseillé de nettoyer de temps en

temps la surface de montage et le support

à l'aide d'un chiffon humide pour éliminer

la poussière et les saletés et empêcher le

support de glisser.



Conçu pour l'iPod® Touch (4e génération),

l'iPod Touch (3e génération), l'iPhone® 4S,

l'iPhone 4, l'iPhone 3GS, l'iPad® 2 et

l'iPad.

La mention « Conçu pour l'iPod, l'iPhone,

l'iPad » signie qu'un accessoire

électronique a été conçu pour se

connecter spécialement aux iPod,

iPhone ou iPad, respectivement, et

que les développeurs ont certié qu'il

satisfaisait aux standards de performance

d'Apple. Apple n'est pas responsable du

fonctionnement de cet appareil ou de

sa conformité aux normes de sécurité

réglementaires. Notez que l'utilisation de

cet accessoire avec un iPod, iPhone ou

iPad peut affecter la performance de la

connexion sans l.

Le capteur GLO est également compatible

avec de nombreux smartphones, tablettes

Otros manuales para GLO Aviation

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de GPS de Garmin

Garmin

Garmin eTrex Legend Cx Manual de usuario

Garmin

Garmin GLO 2 Manual de usuario

Garmin

Garmin GNS 480 Instrucciones de funcionamiento

Garmin

Garmin GPSMAP 4000 Series Manual de usuario

Garmin

Garmin zumo 350LM Manual de instrucciones

Garmin

Garmin Montana 700 Series Manual de usuario

Garmin

Garmin GDL 69A Instrucciones de instalación y funcionamiento

Garmin

Garmin VIB 10 Manual de usuario

Garmin

Garmin Nuvi 710 Manual de instrucciones

Garmin

Garmin GPS 17 Series Manual de usuario

Garmin

Garmin GPSMAP 421 Manual de usuario

Garmin

Garmin nüvi 1250 Manual de instrucciones

Garmin

Garmin eTrex Legend C Manual de usuario

Garmin

Garmin GPSMAP 6008 Manual de usuario

Garmin

Garmin nuvi 1300 Series Manual de instrucciones

Garmin

Garmin GPSMAP 76 series Manual de usuario

Garmin

Garmin iQUE M5 Manual de usuario

Garmin

Garmin Etrex Legend - GPS Receiver Manual de usuario

Garmin

Garmin GTN 625 Manual del propietario

Garmin

Garmin G900X Manual

Garmin

Garmin eTrex Vista Cx eTrex Vista Cx hiking... Manual de usuario

Garmin

Garmin Nuvi 765 - Widescreen Bluetooth Portable GPS... Manual de instrucciones

Garmin

Garmin Approach S2 Manual de usuario

Garmin

Garmin GPSMAP 378 - Marine GPS Receiver Manual de usuario

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario

Kenwood

Kenwood DNN9330BT Manual de usuario

Safelet

Safelet Indra Manual de usuario

Bushnell

Bushnell 360100 Manual de usuario

Geneq

Geneq SXBlue Manual de usuario

ORIGO

ORIGO ED308 Manual de usuario