GAMA Electronics RF120VPRDC Manual de usuario

GAMA Electronics, Inc.

P.O. Box 1488 Crystal Lake, IL 60039 TEL: (815) 356-9600 FAX: (815) 356-9603

WEB: www.gamainc.com

E-MAIL: gama@gamainc.com

RF Receiver Model RF120VPRDC Instruction Manual

Overview.

The RF120VPRDC is an RF receiver operating at a fixed frequency of 340 MHz. The receiver operates from 120VAC

input power and provides a polarity reversing output for use with certain AC powered winches. Winch suppliers such as

Harbor Freight and Northern Tool offer winches that operate from a 120 VAC power source which is rectified to operate a

DC motor. Below is a list of the manufacturers and the corresponding winch model numbers that the RF120VPRDC remote

control will operate with:

Harbor Freight, Chicago Electric Winch Model 96127, 1,500 Pound.

Northern Tool, WARN Winch Model 80010, 1,000 Pound.

Northern Tool, WARN Winch Model 85330, 1,500 Pound.

Northern Tool, Dutton Lainson Model 25046, 4,000 Pound.

Northern Tool, Dutton Lainson Model SA5015AC, 1,200 Pound.

Northern Tool, Dutton Lainson Model SA9015AC, 2,700 Pound.

Northern Tool, Superwinch Model AC1500, 1,500 Pound.

Northern Tool, Superwinch Model AC1,000, 1,000 Pound.

Keeper Winch, Model KAC1500, 1,500 Pound.

Northern Tool, Model 54129, 1,500 Pound.

Each transmitter has a unique address that is transmitted when a button is pressed. A "program" button is provided on the

receiver to program the transmitter(s) address into the receiver's memory. An LED on the receiver indicates the receiver's

programming status and illuminates when the receiver is energized. The receiver is encased in a waterproof enclosure. The

operating range is at least 100 feet.

Polarity reversing output:

The transmitter has two buttons assigned to the motor output. The up (^) button runs the motor in one direction and down

(v) button runs the motor in the opposite direction. A toggle switch is mounted on the receiver and provides manual control

of the output in case the transmitter is not available.

Maximum ratings:

Power for the receiver can be in the range of 100 to 132VAC. The relay contacts are rated at 20 Amperes, 1HP. Operating

temperature range - 0oF to 160oF.

Dimensions:

Receiver dimensions are approximately 5.75" L x 4" W x 2.5" H.

GAMA Electronics, Inc.

P.O. Box 1488 Crystal Lake, IL 60039 TEL: (815) 356-9600 FAX: (815) 356-9603

WEB: www.gamainc.com

E-MAIL: gama@gamainc.com

Input/output Wiring:

Refer to the RF receiver terminal block nameplate when installing the AC input voltage and DC output to the winch. The

120 VAC Line is terminated to the “AC LINE IN’, the 120 VAC input Neutral is terminated to the “AC IN NEUT”

terminal. Both green ground wires from the AC input to the receiver and winch should be connected with a wire nut.

The switch pendent on the winch must be disconnected from the cable. There are 4-wires of the cable that are terminated to

the switch pendent which are wired to the bridge rectifier, these wires must be removed from the switch and installed on the

receiver. The red wire from the switch is terminated to the “DC IN POS” terminal. The black wire is terminated to the “DC

IN NEG” terminal on the receiver. The other two wires from the switch pendent are terminated to the “MOTOR 1” and

“MOTOR 2” terminals on the receiver. Note: The wire colors from the bridge rectifier may be different than

referenced above. Locate the bridge rectifier and document the colors terminated to the rectifier so they are

correctly connected to the receiver terminal block.

Programming instructions:

Each keyfob transmitter has its own unique internal address that is transmitted whenever a button on the keyfob is pressed.

The receiver needs to be programmed to respond only to keyfob transmitters it is intended to operate with. The following

steps configure the receiver to operate with a keyfob transmitter(s). Up to twelve keyfob transmitters can be programmed to

one receiver. Please read the entire programming procedure before starting. Prior to programming the receiver, verify that

the receiver is connected to the input power. When the receiver enters program mode, all previous transmitter addresses that

were programmed will be erased from the receiver's memory.

1. Locate the pushbutton labeled "PROGRAM" on the receiver. Press and hold this button until the red LED next to

the program button illuminates (approximately 5 seconds). The receiver is now in the transmitter program mode.

Release the blue button. All previously programmed transmitter addresses are erased from the receiver's memory.

2. Press any switch on the keyfob transmitter and verify that the red LED on the receiver extinguishes and then

illuminates (blinks once). Release the button.

3. Within 5-seconds of Step 2, press a switch on the next transmitter to be programmed. The red LED on the receiver

will extinguish and illuminate one time for the first transmitter being programmed, twice for the second, three times

for the third, four times for the fourth etc. The receiver will not respond to transmitters that have already been

programmed.

4. After 5-seconds of no switch being pressed on the transmitter(s) the receiver will return to normal operation. The

red LED on the receiver will blink rapidly, then extinguish. The receiver is now in the normal mode of operation.

This completes the programming instructions. The receiver will retain all its programming even when power is

removed.

Tabla de contenidos

Otros manuales de Receptor de GAMA Electronics

GAMA Electronics

GAMA Electronics RF340-400APR Manual de usuario

GAMA Electronics

GAMA Electronics LRF24V1PR-LS Manual de usuario

GAMA Electronics

GAMA Electronics LRF12V1C-WPTX Manual de usuario

GAMA Electronics

GAMA Electronics RFAC-1L Manual de usuario

GAMA Electronics

GAMA Electronics LRF240V1PR Manual de usuario

GAMA Electronics

GAMA Electronics RF12V1PR-LS Manual de usuario

GAMA Electronics

GAMA Electronics RF340-4PR-ASL Manual de usuario

GAMA Electronics

GAMA Electronics LRF12VPRWP-WPE-WPTX Manual de usuario

GAMA Electronics

GAMA Electronics RF340-4PR-ASL-NIS Manual de usuario

GAMA Electronics

GAMA Electronics RF24V-2-ASL Manual de usuario

GAMA Electronics

GAMA Electronics RF24V1PR-ASL-NIS Manual de usuario

GAMA Electronics

GAMA Electronics RF24V1C Manual de usuario

GAMA Electronics

GAMA Electronics RF120VPRDC Manual de usuario

GAMA Electronics

GAMA Electronics RF24V-1PR-ASL Manual de usuario

GAMA Electronics

GAMA Electronics RF340-400APR-WPTX Manual de usuario

GAMA Electronics

GAMA Electronics RF12V-1PR-ASL Manual de usuario

GAMA Electronics

GAMA Electronics RFR12VPRWP Manual de usuario

GAMA Electronics

GAMA Electronics RF12V-2-ASL-NIS Manual de usuario

GAMA Electronics

GAMA Electronics RF340-DRC Manual de usuario

GAMA Electronics

GAMA Electronics LRF240V-2WP Manual de usuario

GAMA Electronics

GAMA Electronics LRF240VPR1L Manual de usuario

GAMA Electronics

GAMA Electronics RFR24VPRWP Manual de usuario

GAMA Electronics

GAMA Electronics RF12V-2PR-ASL Manual de usuario

GAMA Electronics

GAMA Electronics RF240V-2WP-NIS Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario