GAI-Tronics PMA-300 Manual de usuario

Pub.: 42004-667L2A

GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA

610-777-1374 n800-492-1212 nFax: 610-775-6540

GAI-TRONICS CORPORATION

Model PMA-300

300 Watt Central Amplifier

TABLE OF CONTENTS

Confidentiality Notice ..................................................................................................................1

General Information....................................................................................................................1

Product Overview.................................................................................................................................1

System Requirements and Limitations................................................................................................1

Features and Functions........................................................................................................................1

Important Safety Instructions..............................................................................................................2

Description of Major Components ......................................................................................................3

Internal Components ......................................................................................................................................... 3

External Components ........................................................................................................................................ 4

Block Diagram ......................................................................................................................................5

Speakers ................................................................................................................................................5

Speaker Wiring Guidelines................................................................................................................................ 6

Installation ...................................................................................................................................6

Speaker Out Connection ......................................................................................................................8

Bridging of Amplifier Speaker Output Connection ...........................................................................9

Operation....................................................................................................................................10

Maintenance...............................................................................................................................11

External and Internal Adjustment ....................................................................................................11

Troubleshooting..................................................................................................................................11

Specifications .............................................................................................................................12

Replacement Parts..............................................................................................................................13

Pub.: 42004-667L2A

GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA

610-777-1374 n800-492-1212 nFax: 610-775-6540

Model PMA-300

300 Watt Central Amplifier

Confidentiality Notice

This manual is provided solely as an operational, installation, and maintenance guide and contains

sensitive business and technical information which is confidential and proprietary to GAI-Tronics.

GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,

and such information may only be used in connection with the operation of your GAI-Tronics product or

system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any

third party.

General Information

Product Overview

The Model PMA Series products are

industrial rack–mountable public address

power amplifiers. This manual describes the

installation, operation, and maintenance of the

300 W amplifier.

System Requirements and

Limitations

The Model PMA-300 is a 300 Watt Central

Amplifier designed to use speakers with

variable-impedance, line matching

transformers that are made to match the

selected output voltage of the amplifier.

Features and Functions

•Internal power supply with soft-start

•Front panel status indicators

•Compact 19-inch rack mount design (3U)

•Rear mounted Speaker Output connections for 70V (Class 2) OR 100V (Class 1).

•Easy interconnection to system cabling via keyed connectors

•Dual Mic input connector for ease of connecting multiple amplifier inputs in a parallel configuration

•Electronic protection against speaker output short-circuits and overload

Figure 1. PMA-300 Outline Diagram

Page 2of 13

Model PMA-300 300 Watt Central Amplifier Pub.: 42004-667L2A

f:\standard ioms - current release\instr. manuals (42004)\42004-667l2a.doc

12/00

Important Safety Instructions

WARNING When using this product, these basic safety precautions should always

be followed to reduce the risk of fire, electrical shock, and/or injury to persons:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider that the other. A grounding-type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

Page 3of 13

Model PMA-300 300 Watt Central Amplifier Pub.: 42004-667L2A

f:\standard ioms - current release\instr. manuals (42004)\42004-667l2a.doc

12/00

Description of Major Components

This assembly includes external components accessible to the user as well as internal components or

subassemblies.

Internal Components

The assembly contains the following components or subassemblies. Please refer to Figure 2 below for a

top view with the cover removed.

•Chassis

•Amplifier Heat-sink Assembly

•Power Supply (10272) PCBA

•Amplifier (10270) PCBA

•Monitor (10271) PCBA

•AC Power Input Transformer

•Audio Output Transformer

Figure 2. Component Subassembly Detail

Page 4of 13

Model PMA-300 300 Watt Central Amplifier Pub.: 42004-667L2A

f:\standard ioms - current release\instr. manuals (42004)\42004-667l2a.doc

12/00

External Components

The Model PMA-300 Power Amplifier’s front panel includes the following components. Refer to Figure

3 below.

•POWER: This rocker switch controls the main ac power to the amplifier.

•Status Indicator Panel: The status panel is a series of 14 LEDs that indicate the overall status of the

amplifier along with various fault indications.

Refer to Figure 4 for the amplifier’s rear panel diagram for the locations of the following connectors:

•DUAL LINE IN

•DUAL MONITOR OUT

•SPEAKER OUT

•I/O PORT

•ACV IN

•AC PRIMARY LINE FUSE LOCATED WITHIN THE LINE FILTER / IEC CONNECTOR.

Figure 3. PMA-300 Amplifier - Front View

Figure 4. PMA-300 Amplifier – Rear Panel

Page 5of 13

Model PMA-300 300 Watt Central Amplifier Pub.: 42004-667L2A

f:\standard ioms - current release\instr. manuals (42004)\42004-667l2a.doc

12/00

Block Diagram

The block diagram for the PMA-300 Amplifier is shown below:

Speakers

The individual speaker’s power level is determined by the tap settings on the proper V-matched line

matching transformer. Use of these transformers allows the speakers to be placed at long distances from

the amplifier without significant power loss. The number of speakers for a central amplifier system is

limited to the power available from the central amplifier.

The sum of the speaker power settings MUST NOT exceed the total power available from the amplifier.

For an example, a 300-watt central amplifier can drive approximately 40 speakers with drivers tapped at

7.5 watts each.

Figure 5. PMA-300 Block Diagram

Page 6of 13

Model PMA-300 300 Watt Central Amplifier Pub.: 42004-667L2A

f:\standard ioms - current release\instr. manuals (42004)\42004-667l2a.doc

12/00

Speaker Wiring Guidelines

Cable distance should be kept as short as possible to reduce power loss. The following chart illustrates

the correlation between four typical wire sizes and the distance that speakers with integral drivers or horns

with separate drivers can be placed from the central amplifier for a -1 dB loss (-20% power).

Speaker Wiring Guidelines For 300 Watt Central Amplifiers

Wire Size

Central

Amp Line

Voltage 18 AWG (0.82mm2)16 AWG (1.31mm2)14 AWG (2.08mm2)12 AWG (3.31mm2)

100 V Line 319 feet (97 m) 509 feet (155.1 m) 810 feet (246.8 m) 1,289 feet (392.8 m)

70.7 V Line 162 feet (49.3 m) 257 feet (78.3 m) 409 feet (124.6 m) 650 feet (198m)

Installation

WARNING Please follow below recommendations / instructions for installation.

CAUTION These installation instructions are for use by qualified service

personnel only. To reduce the risk of electric shock, DO NOT perform any servicing other

than that contained in the operating instructions unless you are qualified to do so.

1. Ensure that the installation conforms with all applicable local electrical codes.

2. Avoid running input and output signal cabling near high voltage/high electromagnetic sources.

3. When the SPEAKER OUT voltage connection being used is 100V, the amplifier’s Speaker Out

wiring MUST conform to Class 1 wiring specification. When the SPEAKER OUT voltage

connection being used is 70V, Class 2 wiring specification is acceptable.

DANGER Do not install in a hazardous area.

4. Use in safe, non classified, non hazardous areas only.

5. The total power distribution to the speakers MUST NOT exceed the amplifier’s rated output wattage.

Rack Mount Installation

The power amplifier is designed to be mounted in a standard 19-inch equipment rack ONLY. Place the

amplifier in the desired rack location and secure with appropriate rack mounting hardware

(customer-supplied).

Due to the weight of the unit, supporting rails (customer supplied) mounted inside the equipment rack

MUST be used for adequate support of amplifier; however, do not block the heatsink fans preventing

adequate air circulation. Please refer to the equipment rack manufacturer for the appropriate support rails

to use.

Page 7of 13

Model PMA-300 300 Watt Central Amplifier Pub.: 42004-667L2A

f:\standard ioms - current release\instr. manuals (42004)\42004-667l2a.doc

12/00

Ventilation

The amplifier creates heat during operation. Although the amount of heat generated varies depending on

various factors, the unit should be positioned to allow for natural convection air flow to prevent excessive

temperature rise.

If additional amplifiers or other heat producing equipment is installed within the enclosure rack, ensure

that the ambient temperature near the amplifiers does not exceed ~50ºC during normal operation by

installing adequate rack ventilation fans.

Note: If, during normal operation, the ambient temperature exceeds ~50ºC inside the equipment rack,

increase the spacing distance between the amplifiers and equipment and install suitable equipment rack

fans to reduce cabinet’s ambient to below ~ 50ºC.

Audio Line Input Connection

The LINE IN connection is designed to mate with a 3-pin male, XLR-style connector. It can be

connected into either of the two parallel XLR receptacles located on the rear of the amp. Connect the

audio (+) to pin 2 and audio (-) to pin 3 of XLR plug.

The second XLR receptacle can be used to connect the line-in audio signal to additional amplifiers in

parallel, if needed. Connect the audio (+) to pin 2 of each amp and audio (-) to pin 3 of each amp.

Minimum recommended wire gauge is 18 AWG. See Figure 6 below.

Figure 6. LINE IN Connection

Page 8of 13

Model PMA-300 300 Watt Central Amplifier Pub.: 42004-667L2A

f:\standard ioms - current release\instr. manuals (42004)\42004-667l2a.doc

12/00

Speaker Out Connection

The amplifier’s SPEAKER OUT connection uses a keyed, positive-locking Neutrik® SPEAKONTM

connector, which eliminates the possibility of vibrating loose. The ‘keyed’ feature prevents

misconnection to similar style connectors on the amplifier’s rear panel. The amplifier contains a 70V out

and a 100V out connection depending on your constant voltage speaker system.

Notes:

•Use only one of the SPEAKER OUT connections at a time.

•If using the 100V out connection, only CLASS 1 wiring specification is acceptable.

•If using the 70V out connection, CLASS 2 wiring specification is acceptable.

Connect the speakers as follows:

1. To properly terminate to the system speaker cable, use the enclosed SPEAKON™ connector (blue

body), which is supplied with the unit.

2. Determine which SPEAKER OUT voltage, 70.7V or 100V, is required for your constant voltage

speaker system.

3. Determine the desired wire gauge per the Speaker Wire Guidelines chart on page 6.

4. Determine the correct clamping strain relief depending on your cable’s diameter.

5. For 100V Speaker Systems: Connect the audio (+) wire to pin 1 (+) and audio (-) wire to pin 1 (-)

(markings are embossed on body of connector) and tighten securely.

Note: Terminals 2 (+) and 2 (-) are not used. Refer to Figure 4 for connector location.

6. For 70.7V Speaker Systems: Connect the audio (+) wire to pin 2 (+) and audio (-) wire to pin 2 (-)

(markings are embossed on body of connector) and tighten securely.

Note: Terminals 1 (+) and 1 (-) are not used. Refer to Figure 4 for connector location.

Speaker System’s Voltage

Output Needed Corresponding Load Impedance (ohm)

for 300W (Full output)

100 V 33.4 ohm

70.7 V 16.7 ohm

Page 9of 13

Model PMA-300 300 Watt Central Amplifier Pub.: 42004-667L2A

f:\standard ioms - current release\instr. manuals (42004)\42004-667l2a.doc

12/00

Bridging of Amplifier Speaker Output Connection

If the distributed speaker system requires more than 300 watts out, bridging of multiple amplifiers’

speaker out connections in a parallel configuration is needed. The maximum total output power can be

increased in multiples of 300 watts. This is done by connecting the output of each amp required together

in parallel. See chart below and Figure 7 for some examples.

Parallel Configuration Example Chart

Speaker System’s

Constant Voltage Value:

(as designed)

Total System Output

Wattage Needed: (in

watts)

# of PMA-300

amplifiers (300 watt

ea.) required:

100V 500 2

100 V 650 3

70.7V 350 2

70.7V 250 1

The following is a general formula to assist in determining # of amplifiers needed:

____ (Total wattage required)/300 (max. wattage per amp) = _____# of amplifiers needed

(If fraction, round up to next whole number)

When wiring multiple amplifiers’ SPEAKER OUT connections in a PARALLEL configuration, ensure

that the Speaker Out (+) of one amp is connected to the Speaker Out (+) of the second amp and the

Speaker Out (-) of one amp is connected to the Speaker Out (-) of the second amp, etc. Each amplifier

must use the same SPEAKER OUT voltage selection, either 70.7V or 100V connection. Refer to Figure

7 for more details.

Contact GAI-Tronics’ Field Service Department at 800-492-1212 inside the USA or 610-777-1374

outside the USA for further information and assistance.

Figure 7. Bridging of Amplifiers

Tabla de contenidos

Otros manuales de Amplificador de GAI-Tronics

GAI-Tronics

GAI-Tronics 701-307 Manual de usuario

GAI-Tronics

GAI-Tronics 751-001ICS Manual de usuario

GAI-Tronics

GAI-Tronics 723-905 Manual de usuario

GAI-Tronics

GAI-Tronics SP2 Manual de usuario

GAI-Tronics

GAI-Tronics 713-102 Manual de usuario

GAI-Tronics

GAI-Tronics 751-005 Guía de instalación

GAI-Tronics

GAI-Tronics DSA-201 Manual de usuario

GAI-Tronics

GAI-Tronics 701-902 SmartSeries Manual de usuario

GAI-Tronics

GAI-Tronics Page/Party 670-301 Manual de usuario

GAI-Tronics

GAI-Tronics 751-905 Smart SERIES Manual de usuario

GAI-Tronics

GAI-Tronics DSA-101 Manual de usuario

GAI-Tronics

GAI-Tronics 723-003 Guía de instalación

GAI-Tronics

GAI-Tronics 10370-70x Manual de usuario

GAI-Tronics

GAI-Tronics 751-002 Guía de instalación

GAI-Tronics

GAI-Tronics 701 Manual de usuario

GAI-Tronics

GAI-Tronics PA250-001 Manual de usuario

GAI-Tronics

GAI-Tronics SP2 Manual de usuario

GAI-Tronics

GAI-Tronics 709-901 Manual de usuario

GAI-Tronics

GAI-Tronics 701-309 Guía de instalación

GAI-Tronics

GAI-Tronics 723-005 Guía de instalación

GAI-Tronics

GAI-Tronics SP2 Manual de usuario

GAI-Tronics

GAI-Tronics 701-312 Manual de usuario

GAI-Tronics

GAI-Tronics 370-202 Manual de usuario

GAI-Tronics

GAI-Tronics 701-305 Guía de instalación

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario