Furuno FELCOM16 Manual de usuario

PRINTED IN JAPAN

INMARSAT MINI-C MOBILE EARTH STATION

FELCOM16

Confirm that the power supply voltage

is compatible with the voltage rating

of the equipment.

Connection to the wrong power supply

can cause fire or equipment damage. The

voltage rating appears on the label at the

rear of the communication unit.

Use the correct fuse.

Use 10 A fuse (defalt setting) for 12 VDC

power supply, or replace the fuse to 5 A

(supplied as spare parts) with 24 VDC.

Use of wrong fuse can result in damage to

the equipment.

Keep the following compass safe

distances.

Standard Steering

Antenna Unit IC-116

Communication Unit IC-216

AC/DC Power Supply Unit

PR-240-CE

SAFETY INSTRUCTIONS

Do not open the equipment

unless totally familiar with

electrical circuits and

service manual.

Only qualified personnel

should work inside the

equipment.

WARNING

Turn off the power at the

mains switchboard before

beginning the installation.

Post a sign near the switch

to indicate it should not be

turned on while the equip-

ment is being installed.

Fire, electrical shock or

serious injury can result if the

power is left on or is applied

while the eqiuipment is being

installed.

ELECTRICAL

SHOCK

HAZARD

0.3 m 0.3 m

0.9 m 0.6 m

Do not approach the ra-

dome closer than 60 cm

when it is transmitting.

Microwave radiation can

cause severe injury or illness.

Radiation level:

10 W/m at 60 cm

CAUTION

Attach securely protection

earth to the ship's body.

The protection earth is required

to the power supply to prevent

electrical shock

TABLE OF CONTENTS

EQUIPMENT LISTS.............................................................................................iii

SYSTEM CONFIGURATION................................................................................ iv

1. MOUNTING THE UNIT .....................................................................................1

1.1Antenna Unit....................................................................................................................1

1.2 Communication Unit........................................................................................................7

1.3AC/DC Power Supply Unit PR-240-CE (option) ...............................................................7

2. WIRING ............................................................................................................. 8

2.1Antenna Cable Connector at the Terminal Unit ................................................................9

3. SETTINGS AFTER THE INSTALLATION....................................................... 11

3.1 Installing software..........................................................................................................11

3.2 Setting the IMN (Inmarsat Mobile No.)...........................................................................15

4. CHANGING SHIP’S MAINS SPECIFICATIONS.............................................12

PACKING LISTS ............................................................................................... A-1

OUTLINE DRAWINGS...................................................................................... D-1

INTERCONNECTION DIAGRAM ......................................................................S-1

iii

EQUIPMENT LISTS

Standard Supply

Name Type Code No. Qty Remarks

Antenna Unit IC-116 - 1

Communication Unit IC-216 - 1

Junction Box* IC-315 - 1

w/CP16-02501

SSAS Alert Unit* IC-307 - 2

w/CP16-03101, FP16-00901

CP16-02101 004-439-060 For 15/30 m antenna cable**

CP16-02111 004-439-070 For 50 m antenna cable**

CP16-02121 004-439-080

1 set For 100 m antenna cable**

TP58A15W-RG58 000-146-252 15 m antenna cable

TP5FBAW-5DFBB 000-146-250 30 m antenna cable

8D-FB-CV 000-117-599 50 m antenna cable

12D-SFA-CV 000-138-866 100 m antenna cable

Installation Materials*

CP16-02401 004-439-540

For communication unit**

Accessories* FP16-00700 004-439-550 1 set FD-ROM, FD (FP16-00601)**

Spare Parts* SP16-01401 004-439-530 1 set Fuse

*: SSAS Specification only.

**: See packing lists at the back of this manual.

Optional Supply

Name Type Code No. Qty Remarks

Cable assy 17JE-573-10 000-127-108 1 For PC connecting

AC/DC Power Supply Unit PR-240-CE - 1 set w/CP24-00151**

000-560-452 For junction box, 10m

000-103-868 For junction box, 20m

000-103-869 For junction box, 30m

000-132-829 For junction box, 40m

5-pair cable CO-SPEVV-

SB-C 0.2x5P

000-132-828

For junction box, 50m

SSASAlert Unit IC-307 000-043-473 1 w/CP16-03101, FP16-00901

Flush Mount Kit OP16-28 004-448-010 1 For SSAS alert unit

SYSTEM CONFIGURATION

Antenna Unit Exposed to Weather

Communication Unit Protected from Weather

Other Units Protected from Weather

PERSONAL

COMPUTER

(PC/AT compatible)

ANTENNA

UNIT

IC-116

COMMUNICATION UNIT IC-216

(with internal GPS receiver)

POWER SUPPLY

100/115/220/230 VAC

1φ, 50/60 Hz

: Standard

: Option

: Local Supply

POWER SUPPLY

12-24 VDC

AC-DC

Power Supply

PR-240-CE

POWER I

INMARSAT MINI-C MOBILE EARTH STATION

FURUNO

POWER

ERROR

PRINTER

JUNCTION BOX

IC-315

SSAS ALERT UNIT*

IC-307

SSAS ALERT UNIT*

IC-307

*: At least two SSAS Alert Units are required.

CATEGORY OF UNITS

(Max. 3 units)

1. MOUNTING THE UNIT

1.1 Antenna Unit

Mounting Location

• Mount the omnidirectional antenna unit high atop a mast clear of stays and the turning

diameter of a radar antenna. The ideal mounting location would be where no obstacle

appears in the fore and aft directions down to -5º and down to -15º in the port and

starboard directions. This concept is illustrated in the figure below. Shadow sector of the

antenna mast, whip antenna, etc. should be within 2 degrees at one meter from the

antenna unit.

ANTENNA UNIT

515

Antenna unit mounting location

• If both Inmarsat-Aor B ship earth stations are installed, separate the Inmarsat-A/B

antenna at least 8 m.

• Separate the antenna unit from an S-band radar as follows:

HORIZONTAL LINE

Install above this line

PROHIBITED

ZONE

1.5 m

5 m

2 m

S-band radar

INSTALLTION

ZONE

2 m

S-band radar and installation area

1. MOUNTING THE UNIT

• The allowable vibration level as specified by Inmarsat is as shown in the table below.

Allowable vibration level

Frequency Level

2 to 10 Hz 2.54 mm Peak Amplitude

10 to 100 Hz 9.8 m/s² Peak Acceleration

• Avoid the location near funnels and stacks; smoke and soot on the radome can lower

signal level.

• Separate the antenna unit 5 m from HF, VHF or 27 MHz antenna.

Mounting

Fifteen, 30, 50 or 100 m antenna cable is available. Fifteen and 30 m cable has connectors

on both ends, and one connector for 50/100 m cable. Do not shorten these cables to

prevent interference. To mount the antenna unit, an exclusive pipe is necessary.

Locally prepare an antenna mast with a ground stud (M6 stainless steel bolt welded to

antenna mast) and mounting pipe with threads and plate (See the outline drawing of the

mounting plate shown below.) Weld the mounting pipe to the antenna mast.

The distance between the stud and the earth terminal on the antenna unit should be within

340 mm, which also is the length of the supplied ground wire.

Mounting pipe and antenna mast

1. MOUNTING THE UNIT

For 15 or 30 m cable

1. Apply silicone sealant (local supply) to the threads of the pipe.

2. Unscrew three screws to remove the antenna base from the antenna unit.

3. Pass the antenna cable through the pipe, antenna base in order.

4. Insert the cable protector (supplied) into the slot at the bottom of antenna base.

5. Screw the antenna base onto the antenna pipe by rotating the antenna base.

6. Pass the antenna cable through the shrink tube (supplied).

7. Attach the antenna cable to the connector at the bottom of the antenna unit (upper).

8. Slide up the shrink tube until it touches the bottom of the antenna unit (upper).

9. Heat the above shrink tube, and then apply silicone sealant around the upper edge of

the tube. Also wind self-bonding tape around the lower edge of the shrink tube and then

wrap vinyl tape over self-bonding tape.

Note: Between the bottom of the antenna unit (upper) and the end of the taping should be

less than 50 mm.

Antenna unit, passing the cable through the pipe

1. MOUNTING THE UNIT

10.Wrap self-bonding tape around the connection of antenna base and pipe, and then wind

vinyl tape over self-bonding tape.

11.Remount the antenna unit (upper) on the antenna base. (Torque: 2.6 N·m ± 10%)

12.Fix the ground wire RW-4747 (supplied) between the ground terminal on the antenna

unit and the ship’s ground point.

Mounting

13.Apply silicone sealant (supplied) to the ground terminal and three screws at the bottom

of antenna base.

14.Fix the antenna cable to the mast with a cable tie (local supply).

1. MOUNTING THE UNIT

For 50 or 100 m cable

1. Apply silicone sealant (local supply) to the threads of the pipe.

2. Unscrew three screws to remove the antenna base from the antenna unit.

3. Pass the cable assy TPA5FB0.3NJ5FBA-5DFB (supplied, 300 mm) through the shrink

tube (supplied).

4. Attach the above cable assy to the connector at the bottom of the antenna unit (upper).

5. Slide up the shrink tube until it touches the bottom of the antenna unit (upper).

6. Heat the shrink tube, and then apply silicone sealant around the upper edge of the tube,

also wind self-bonding tape around the lower edge of the shrink tube and then wrap

vinyl tape over self-bonding tape.

Note: Between the bottom of the antenna unit (upper) and the end of the taping should be

less than 50 mm.

7. Insert the cable protector (supplied) in to the slot at the bottom of the antenna base.

8. Pass the antenna cable through the pipe, antenna base in order.

When laying the cable along side the pipe, put the cable aside to pass through the projection

in the antenna base. See [A] in the figure shown below.

Waterproofing

9. Remount the antenna unit (upper) on the antenna base. (Torque: 2.6 N·m ± 10%)

10.Screw the antenna unit onto the antenna pipe by rotating the antenna unit.

11.Wind self-bonding tape (supplied) at the connection of antenna base and pipe, and then

wrap vinyl tape over self-bonding tape.

Tabla de contenidos

Otros manuales de Sistema de seguridad de Furuno

Furuno

Furuno BR-1000 Manual de usuario

Furuno

Furuno BR-500 Manual de usuario

Furuno

Furuno felcom15 Manual de usuario

Furuno

Furuno BR-500 Manual de usuario

Furuno

Furuno BR-500 Manual de usuario

Furuno

Furuno IC-307 Manual de usuario

Furuno

Furuno BR-1000 Manual de usuario

Furuno

Furuno IC-350 Manual de usuario

Furuno

Furuno FB-3101 Manual de usuario

Furuno

Furuno SSAS Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario