Furious FPV Acrowhoop v2 Instrucciones de montaje

Tabla de contenidos

Otros manuales de Controladores de Furious FPV

Furious FPV

Furious FPV Fortini F4 OSD Manual de usuario

Furious FPV

Furious FPV F-35 LIGHTNING Manual de usuario

Furious FPV

Furious FPV PIKO F4 Manual de usuario

Furious FPV

Furious FPV Radiance DSHOT Manual de usuario

Furious FPV

Furious FPV Fortini F4 OSD REV.3 Manual de usuario

Furious FPV

Furious FPV FORTINI F4 Manual de usuario

Furious FPV

Furious FPV Radiance DSHOT Manual de usuario

Furious FPV

Furious FPV RACEPIT Manual de usuario

Furious FPV

Furious FPV PIKO F4 OSD Manual de usuario

Furious FPV

Furious FPV FORTINI F4 Manual de usuario

Furious FPV

Furious FPV RACEWHOOP Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

1

https://furiousfpv.com

How to do connect FRSKY DJT Module with Acrowhoop v2.

Step1: Choose Mode Module to D8.

On the DJT module of FrSky Taranis transmitter. Change Mode of Module is Two

Way Mode by switchs like as this picture.

SW1: OFF SW2: OFF

2

https://furiousfpv.com

Step 2: Configure module for Transmitter:

From Home screen on your transmitter, press Menu button > Page button to go

to Model Setup page 2/12.

On Model Setup page 2/12, press ADD or Minus button more times to go to:

-Internal RF: at Internal RF we stay Mode press Enter >press ADD or Minus

change to OFF for turn OFF Internal Module.

After that, we go to External RF

-At External RF, we stay Mode press Enter > ADD change OFF to PPM.

-Turn Off transmitter.

Your transmitter had configuration look like this picture.

Now we will Bind Acrowhoop V2 with Taranis use external module Frsky DJT.

Step 3: Active Bind mode for Acrowhoop V2:

Plug Battery 1 cell for FC Acrowhoop v2.

Hold Bind button while you plug battery, when you plug Battery at the Top Side

you will see BLUE LED turn on.

3

https://furiousfpv.com

After plug Battery release Bind button.

Step 4: Bind transmitter with Acrowhoop:

Binding is the process of uniquely associating a particular receiver to a transmitter

module. A transmitter module can be bound to multiple receivers (not to be used

simultaneously). A receiver can only be bound to one transmitter module. Follow

the steps below to finish the binding procedure.

1. Turn on the transmitter while holding the F/S button on the DJT module (see

Mode and Compatibility table above). Release the button. The RED LED on the

DJT module will flash and GREEN LED ON , indicating the transmitter is ready to

bind to the receiver.

When BLUE LED on FC turn off, successful bind.

2. Turn off both the transmitter and the Acrowhoop.

4. Turn on the transmitter and plug battery for Acrowhoop. The BLUE LED on the

Acrowhoop indicates the Acrowhoop is receiving commands from the transmitter.

The Acrowhoop/transmitter module binding will not have to be repeated, unless

one of the two is replaced