FULLY WIRED ELECTRONICS Mini-Logic Manual de usuario
Fully Wired Electronics - Mini-Logic
User Manual
Fully Wired Electronics - Mini-Logic
User Manual v1.0
Contents:
Limited Warranty………………….................................................................................2
Installation and Safety……….......................................................................................3
Foreword…..................................................................................................................4
Module Overview…………………………………………………….................................5
Logic Gates in Practice……………………………………………………………………..7
NOT Gates……………………………………………………………………………..7
AND Gates……………………………………………………………………………..8
NAND Gates…………………………………………………………………………...9
OR Gates……………………………………………………………………………..10
NOR Gates……………………………………………………………………………11
XOR Gates……………………………………………………………………………12
XNOR Gates………………………………………………………………………….13
Technical Specifications.............................................................................................14
1
Fully Wired Electronics - Mini-Logic
User Manual v1.0
Limited Warranty:
Fully Wired Electronics warrants this product to be free of defects in materials or
construction for a one year (twelve month) period from the date of purchase1. Proof
of purchase via a receipt or invoice is required when making a warranty claim.
Malfunction resulting from incorrect power supply voltages, reversed or backwards
Eurorack bus board connections, faulty or damaged cables, incorrect patching,
general misuse, the modification of the faceplate and/or the products circuitry or any
other causes of malfunction that Fully Wired Electronics deems to be at the fault of
the user are not covered by this limited warranty. Normal service rates will be
applied.
Attempting to alter and/or modify this product in any way will void this limited
warranty.
During this one year limited warranty period, all defective products will be repaired or
replaced at the discretion of Fully Wired Electronics. Products must be returned
directly to Fully Wired Electronics, with the customer paying the cost of transit to
Fully Wired Electronics.
Fully Wired Electronics accepts and implies that no responsibility will be taken for
harm to person and equipment through the operation of this product.
1For pre-orders this is applicable from the date of shipment rather than the date of purchase
2
Fully Wired Electronics - Mini-Logic
User Manual v1.0
Installation and Safety:
Prior to installing and uninstalling this product, please ensure that your Eurorack
power supply is turned OFF. Installing or uninstalling this product without doing so is
potentially dangerous, running the risk of causing damage to your equipment and
electrocuting yourself. To minimise the possibility of backwards or reversed power
supply connections, the module is fitted with a shrouded 10 (2x5) pin header.
Despite this precaution please ensure that both the power cable header, and the
power supply headers are orientated correctly. Also ensure that there is NO damage
to the power cable being used. A damaged power cable may cause harm to the
module, the power supply being used, or yourself!
3
Fully Wired Electronics - Mini-Logic
User Manual v1.0
Foreword:
Thank you for purchasing the Fully Wired Electronics - Mini-Logic. We value all of
our customers for their support. Your purchase is greatly appreciated!
Special thanks to everyone who was involved during the development and
production of this module, and the journey of Fully Wired Electronics for your help
and unwavering support!
4
Fully Wired Electronics - Mini-Logic
User Manual v1.0
Module Overview:
The Fully Wired Electronics - Mini-Logic is a 2 input, 8 output 6HP Boolean Logic
module, outputting all Boolean Logic types according to the state of both gate inputs.
The module features AND, NAND, OR, NOR, XOR, XNOR and two NOT outputs.
For more information on logic gates and their functions, please see the subsequent
chapter (Logic Gates in Practice).
Fig 1. Mini-Logic panel overview
5
Fully Wired Electronics - Mini-Logic
User Manual v1.0
The two inputs, both located at the top of the module, work independently of each
other. When a gate or trigger signal is detected on one of the inputs, the associated
input LED, which is located directly under the both inputs, will illuminate. Both inputs
are used to alter the states of the outputs, and is the only way to do so on the
Mini-Logic. Each of the outputs are visualised on the module through the use of
rectangular boxes around each of the output jack sockets. The output states for each
of the logic types are indicated through the LEDs located below its associated output
jack socket. By default the NOT 1, NOT 2, NAND, NOR and XNOR LEDs will all be
illuminated once the module receives power, assuming no gate or trigger signal is
active at either of the inputs. Once a gate or trigger signal is detected the states of
each output, and its respective LED, will change according to the appropriate truth
table for the logic gate type.
Each input would expect to receive a +5V gate or trigger signal, however under
normal operation should tolerate signals up to +12V. The Mini-Logic will only output
+5V signals.
6
Fully Wired Electronics - Mini-Logic
User Manual v1.0
Logic Gates in Practice:
NOT Gates:
NOT gates are the simplest of the 7 logic types, as they have a single input and a
single output. This gate type simply outputs an inverted copy of the signal at its input.
This means if the state of the input is logical low (0), the output state will be logical
high (1). The reverse of this is also true, meaning a logical high (1) at the input, will
result in a logical low at the output. This can be seen in Fig. 2 below.
Fig. 2 - NOT Gate Truth Table
7
Fully Wired Electronics - Mini-Logic
User Manual v1.0
AND Gates:
The output of the AND gate remains in a low (0) state, whilst both of the inputs are in
a logical low (0) state. The same is true if only one of the inputs receives a signal
and enters a logical high (1) state. Both inputs are required to be in a logical high (1)
state for the output to go into a high (1) state, as seen in Fig. 3.
Fig. 3 - AND Gate Truth Table
8
Fully Wired Electronics - Mini-Logic
User Manual v1.0
NAND Gates:
NAND Gates build upon AND gates through incorporating NOT gates, causing the
inverse operation. The output of a NAND gate will remain in a logical high (1) state
until both inputs (in the case of a two input NAND gate) are in a high (1) state, at
which point the output will turn to a logic low (0) state. If only one of the inputs is in a
high (1) state, the output will remain high (1), as seen in Fig. 4, Due to this
functionality, NAND gates are the inverse of AND gates.
Fig. 4 - NAND Gate Truth Table
9
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Unidad de control de FULLY WIRED ELECTRONICS
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
