Fujitsu SP-1120 Guía de configuración
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
1
CG00002-291501
SP1120\1125\1130
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
2
CG00002-291501
Consumables and Replacement Cycles
Consumables need to be replaced
periodically. It is recommended that you
keep a stock of new consumables for
replacement before it reaches the end of its
life. The scanner records the number of
sheets scanned after replacing the
consumables, which allows you to check the
status of the consumables.
Note that the suggested replacement cycles
are references for using A4 (80 g/m2(20 lb)
wood-free or wood-containing paper, as
these cycles vary depending on the type of
documents scanned and how often the
scanner is used and cleaned.
HINT
Only use the specified consumables.
To purchase the consumables, contact your
FUJITSU scanner dealer or an authorized
FUJITSU scanner service provider.
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
3
CG00002-291501
Replacing the Roller Set
The roller set consists of a brake roller and a pick roller. Replace each roller in the following
procedure.
5. Attach a new brake roller on the shaft
1Remove all documents from the ADF paper chute (feeder).
2
Open the ADF.
.
3
Remove the brake roller.
a. Press the cover bushing of the brake roller to open the cover in the
direction of the arrow.
CAUTION
Be careful not to have your fingers caught
when the ADF closes.
b. Pull out the left side of the brake roller shaft, and then pull out the right side of the shaft from the hole.
4. Remove the brake roller from its shaft
Brake Roller
Brake Roller Shaft
Brake Roller Shaft
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
4
CG00002-291501
Insert the protrusion on the shaft into the slot.
6. Attach the shaft.
a. Attach the notch, which is on the brake roller shaft, to the slot on the right then attach the left side of
the shaft.
b. Close the cover.
ATTENTION
Confirm that the brake roller is installed properly. Otherwise, it may cause feeding errors such as paper
jams.
Notch
Brake Roller
Protrusion
Brake Roller Shaft
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
5
CG00002-291501
7. Remove the pick roller.
a. Open the side guide fully to both sides. Then place your finger into the depression and open the sheet
guide in the direction of the arrow.
b. Slide the pick roller and remove it from the top.
Side Guide
Depression
Side Guide
Sheet Guide
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
6
CG00002-291501
8. Attach a new pick roller from the bottom.
a. Check the direction of the notch on the pick roller and of the small roller, and insert it in the hole.
b. Close the sheet guide.
ATTENTION
Check that the pick roller is installed properly. Otherwise, it may cause feeding errors such as paper jams.
9. Close the ADF.
Be careful not to have your fingers caught when the ADF closes.
10.Reset the roller set counter.
Start the Software Operation Panel and reset the counter.
Notch
Small Roller
CAUTION
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
7
CG00002-291501
Checking and Resetting the Sheet Counters
Checking the sheet counters
The status on each consumable part can be checked to determine when to replace the
consumables.
When a consumable needs to be replaced soon, the background color of the counter for the
consumable changes. The background color of the roller set counter turns light yellow when the
number of sheets scanned reaches 95,000, and turns yellow when it reaches 100,000.
Start the Software Operation Panel
Check that the scanner is connected to the computer, then turn on the scanner.
Display the [Software Operation Panel] window.
Windows Vista/Windows Server 2008/Windows 7
oSelect the [Start] menu - [All Programs] –[SP Series] - [Software
Operation Panel].
Windows Server 2012/Windows 8
oRight-click the Start screen, and select [All apps] on the app bar - [Software
Operation Panel] under [SP Series].
Windows Server 2012 R2/Windows 8.1
Select [|] on the lower left side of the Start screen - [Software Operation Panel] under [SP
Series]
From the listing on the left, select
[Device Setting].
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
8
CG00002-291501
Resetting the sheet counters
When you have replaced or cleaned a consumable part, reset the corresponding counter by
using the following procedure.
1Click the [Clear] button for the consumable that you replaced.
2Click the [OK] button in the Software Operation Panel.
A confirmation message appears.
3Click the [OK] button.
The settings are saved.
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
9
CG00002-291501
Cleaning Materials and Locations that Require Cleaning
Notes
Part No.
Name
Cleaning Materials
Cleaner F1
PA03950-
0352
1 bottle (100 ml)
Moisten a cloth or Cleaning
Paper with this liquid to
wipe the scanner clean.
It may take a long time to
dry if an excessive amount
is used. Use it in small
quantity. Wipe off the
cleaner completely to leave
no residue on the cleaned
parts.
Cleaning
Paper
CA99501-
0012
1 pack (10 sheets)
Use this non-woven sheet
with Cleaner F1.
Cleaning Wipe
PA03950-
0419
1 box (24 packets) Pre-moistened
with Cleaner F1. It can be used
instead of moistening a cloth with
Cleaner
CLEANING SWAB
(100 / PK)
CG90000-
120601
CLEANING CLOTH
(25/PK)
ATTENTION
In order to use the cleaning materials safely and correctly, read
the precautions on each product thoroughly.
For more information about the cleaning materials, contact your
FUJITSU scanner dealer or an authorized FUJITSU scanner
service provider.
CG90000-
120001
SP1120\1125\1130 Consumable Replacement and Cleaning
Instructions
10
CG00002-291501
Location and Frequency
Location
Frequency
ADF
Brake roller
Every 3,000 sheets
Pick roller
Plastic idler roller
Glass
Ultrasonic sensor
Feed roller
Eject roller
ATTENTION
Cleaning cycles may vary depending on the condition of the
documents. Also, cleaning must be performed more frequently when
the following types of documents are scanned:
•Smooth-faced documents such as coated paper
•Documents with printed text/graphics that almost cover the entire
surface
•Documents containing a large amount of calcium carbonate
•Documents written in lead pencil
•Documents on which the toner is not sufficiently fused
Otros manuales para SP-1120
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Escáner de Fujitsu
Fujitsu
Fujitsu ScanPartner 3092DC Manual de usuario
Fujitsu
Fujitsu ScanSnap fi-5110EOXM Manual
Fujitsu
Fujitsu ScanSnap N1800 Manual
Fujitsu
Fujitsu S500M - ScanSnap - Document Scanner Manual de usuario
Fujitsu
Fujitsu ScanSnap N1800 Manual de usuario
Fujitsu
Fujitsu ScanSnap S1100i Instrucciones de montaje
Fujitsu
Fujitsu ScanSnap S1100 Manual
Fujitsu
Fujitsu M4097D - Fb 50PPM SCSI A3 Dupl 100Sht Adf Manual
Fujitsu
Fujitsu ScanSnap fi-5110C Manual
Fujitsu
Fujitsu fi 5750C - Document Scanner Manual
Fujitsu
Fujitsu fi-4530C Manual
Fujitsu
Fujitsu FI-6230 Manual
Fujitsu
Fujitsu fi-4220C2 Guía de configuración
Fujitsu
Fujitsu fi-6670 Series Manual de usuario
Fujitsu
Fujitsu fi-4340C Manual
Fujitsu
Fujitsu ScanSnap iX500 Manual de usuario
Fujitsu
Fujitsu ScanSnap iX500 Instrucciones de montaje
Fujitsu
Fujitsu fi-6130Z Manual de usuario
Fujitsu
Fujitsu SP-1130Ne Manual
Fujitsu
Fujitsu fi-6800 Manual de usuario
Manuales populares de Escáner de otras marcas
Infinite Peripherals
Infinite Peripherals INFINEA TAB M Manual de usuario
Mustek
Mustek PageExpress 4800 Pro Manual de usuario
Optex
Optex 750830 Manual de usuario
Innova
Innova 5210 Manual de usuario
Visioneer
Visioneer CardReader 100 Guía de inicio rápido
Rohde & Schwarz
Rohde & Schwarz TSME6 Manual de usuario