FujiFilm Apeos C7070 Manual de usuario
September 2021 GM1049E2-3 Edition1 FUJIFILM Business Innovation Corp.
Apeos™ C7070 Apeos C6570
Apeos C5570 Apeos C4570
Apeos C3570 Apeos C3070
Reference Guide
Appendix
21 Preface
1Preface
A guide describing the emulation mode, direct print, web applications, troubleshooting, etc.
Refer to Reference Guide - Main Unit for trademarks and manual conventions.
This manual may not be edited, modified or copied in whole or part without the written consent
of the publisher.
Parts of this manual is subject to change without prior notice.
The screen shots and the illustrations in this manual are used as examples. They may differ from
yours depending on the model, the software, or the OS.
3
2.1 Emulation
2Appendix
2.1 Emulation
When using the emulation mode, you can get the print results similar to those of other companies'
printers.
Overview of Emulation Feature
This machine is compatible with following emulation mode.
Note
For details of each mode, contact your local representative.
Changing the print language
This machine is compatible with multi-emulation. Due to this, you can switch the corresponding print
language.
Changing the command
There are commands to change the corresponding print language.
Automatic change
The machine analyzes the data received by the host interface and automatically identifies the print
language.
Protocol dependence
You can fix the print language for each protocol (USB, IPP, LPD, Port9100, WSD).
Log in to Administrator Mode in Internet Services, and set Print Mode for each protocol in [USB] or
[Protocols] of the [Network] tab.
Available font
User-defined characters (external fonts) can be used with ESC/P.
User-defined characters are registered as bitmap fonts and saved even after the power is turned off.
Sharing between print languages is not possible.
Emulation mode Printer to be emulated
ESC/P LQ1900K II+
PCL HP-CLJ5500 (color), HP-LJ4200 (black and white)
HP-GL 7586B or DJ750C Plus
HP-GL/2 DJ750C Plus
42 Appendix
Print function
N Pages
2 pages are available.
Form
You can register standard forms and print the registered forms by synthesizing them into print data.
Note
If you try to register more forms than the maximum number of forms to be registered or if the form
memory reaches full capacity, new forms cannot be registered.
Barcode
Barcode standards available for ESC/P are JAN code, CODE39, CODABAR, Industrial 2 of 5, Matrix 2
of 5, and Interleaved 2 of 5.
Barcode standards available for PCL are CODE128, Postal barcode, and QR code.
Output of Related List
Refer
For details, refer to “Basic Operations” in Reference Guide - Operations.
Font
Available font can be confirmed by executing [Print] for [Font List] or [PCL Font List] in > [Device
Status] > [Print Reports] > [Printer Reports].
Form
You can confirm the form by execute [Print] in > [Device Status] > [Print Reports] > [Printer
Reports] > [ART IV, ESC/P User Defined List].
Barcode
You can confirm the method to specify commands by execute [Print] in > [Device Status] > [Print
Reports] > [PCL Font List].
Associated Device Menu
Log in to Administrator Mode.
Emulation mode N Pages Form Barcode
ESC/P Yes Up to 64 Yes
PCL - - Yes
HP-GL, HP-GL/2 - - -
Emulation mode [Port Settings] [Allocate Memory] [Delete Form]
ESC/P Yes Yes Yes
PCL Yes - -
HP-GL, HP-GL/2 Yes Yes -
5
2.1 Emulation
Port Settings
Set in > [Device] > [Network Settings] > [Port Settings].
Enable port (USB/LPD/IPP/Port9100/WSD)
Launch the port to be used in the emulation mode.
Allocate Memory
Set in > [Device] > [App Settings] > [Print Settings] > [Allocate Memory].
Note
If storage is attached, the settings cannot be changed.
Delete Form
Set the mode to delete forms in > [Device] > [App Settings] > [Print Settings] > [Delete Form].
Emulation Mode
The unique settings for each emulation modes can be changed in > [Device Status] > [Print
Mode].
Note
[Retrieve Programming], [Store/Delete Programming] and [Default Programming] are displayed on ESC/
P, HP-GL/2.
You can set these items also with Internet Services in the same procedure.
Retrieve Programming
Retrieve settings stored in the memory.
Programming
Enter the Item Number for the function in [Item Number] to display the current setting.
Enter the new value in [New Value] and tap on [Save] to change the setting.
Refer
Refer to "Items" (P.13) for Item Number.
Store/Delete Programming
Store the current Items details in [Custom Settings] and delete stored memory.
Default Programming
Set the default values.
62 Appendix
HP-GL, HP-GL/2 Emulation-specific Matters
Printable area
SEF
Paper
size
Paper length
(1/7200″)
Coordinate value (1/7200″)
X
direction
Y
direction
Margin Printable area Top right corner Margin
Length Width Bottom
left X
Bottom
left Y
Long
side
Short
side
Top
right X
Top
right Y
XR YU
A3 119052 84168 1260 1260 116532 81648 117792 82908 1260 1260
A4 84168 59508 1260 1260 81648 56988 82908 58248 1260 1260
A5 59508 41940 1260 1260 56988 39420 58248 40680 1260 1260
JIS B4 103176 72828 1260 1260 100656 70308 101916 71568 1260 1260
JIS B5 72828 51588 1260 1260 70308 49068 71568 50328 1260 1260
Short side
Printable area
Paper size
(0,0)
(Bottom left X, Bottom left Y)
(Top right X, Top right Y)
Long side
Margin YU
Margin XR
7
2.1 Emulation
LEF
Paper
size
Paper length
(1/7200″)
Coordinate value (1/7200″)
X
direction
Y
direction
Margin Printable area Top right corner Margin
Length Width Bottom
left X
Bottom
left Y
Long
side
Short
side
Top
right X
Top
right Y
XR YU
A3 84168 119052 1260 1260 81648 116532 82908 117792 1260 1260
A4 59508 84168 1260 1260 56988 81648 58248 82908 1260 1260
A5 41940 59508 1260 1260 39420 56988 40680 58248 1260 1260
JIS B4 72828 103176 1260 1260 70308 100656 71568 101916 1260 1260
JIS B5 51588 72828 1260 1260 49068 70308 50328 71568 1260 1260
Printable area
Paper size
(Top right X, Top right Y)
(Bottom left X, Bottom left Y)
(0,0)
Long side
Short side
Margin XR
Margin YU
82 Appendix
Hard Clip
Area determined by coordinates is called Hard Clip area.
Hard Clip area is determined by the printable area or paper size.
When the size is A3 and the starting point is the bottom left
Standard
Printable area of this machine is the Hard Clip area.
Paper
Same size as the paper is the Hard Clip area.
Auto Layout
Printed area is automatically determined based on the specified items, such as the document size
and paper size.
[Original Size]
Set to [Auto Detect] when using Auto Layout.
[Auto Layout]
Reduce/enlarge the document data to fit the paper size.
[Zoom]
You can enlarge/reduce the printed area to fit the drawn object area in the paper size.
+Y
Printable area（＝Standard Hard Clip area）
Paper size（＝Paper Hard Clip area）
(0,0) Paper origin
(0,0) Standard origin
(16798,11876)
(16442,11520)
+X
Width
Length
9
2.1 Emulation
[Zoom Mode]
[Area Determine Mode]
Note
The object area is determined in [Adapted] without a command.
[Paper Margin]
You can specify the margin.
[Pen Attributes]
You can specify the setting for the pen to draw the boundary lines for the Hard Clip area.
You can set 16 attributes from [Pen Attributes 0] to [Pen Attributes 15].
[Paper Size] Document size is determined based on the drawn object area. Sizes
to be determined are A sizes (6 types from A0 through A5).
[Coordinate Area] Document size is determined based on the starting point of the
drawn object area.
[Auto] Selected automatically. The priority order is [PS] -> [IW] -> [IP] ->
[Adapted].
[IW] Area specified by the last IW command within the data is the object
area.
[IP] Area specified by all IP commands is the object area.
[Adapted] Object area is determined automatically.
[PS] Area including the area specified by the PS command in the
beginning is the object area.
[Pen Width] If reduced by the combination of [Original Size] and [Paper Size], the
pen width is also reduced.
Line width grows thicker from the center of the line.
If the width is 0.0 mm, nothing will be drawn.
[Line End] You can specify the end shape for the pen.
[Line Intersect] You can specify how pen lines are processed when connected.
Note
[None] has the shortest processing time and is suitable for checking.
If symbols are specified by symbol mode commands, connection
process is not performed. Symbol mode commands refer to HPGL
commands that specify symbols.
These settings are not valid for characters.
[Color] Pen colors are specified with RGB. This setting is available for color
printers.
[Density] You can specify the pen intensity. This setting is available for black
and white printers.
10 2 Appendix
Item combination examples in Auto Layout
[Zoom Mode]: [Paper Size], [Zoom]: ON
Image is reduced/enlarged within the printed area and printed.
[Zoom Mode]: [Paper Size], [Zoom]: OFF
Image is printed in the actual size.
Due to this, areas larger than the paper size are not printed.
Object area determined in “Area Judgement Mode”
Printable area
Paper size
Drawn object area ( = Print area)
Object area determined in “Area Judgement Mode”
Printable area
Paper size
Drawn object area ( = Print area)
Otros manuales para Apeos C7070
5
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Impresora de FujiFilm
FujiFilm
FujiFilm ApeosPro C810 Manual de usuario
FujiFilm
FujiFilm ASK-300 Manual del propietario
FujiFilm
FujiFilm instax mini Link 2 Manual de usuario
FujiFilm
FujiFilm PICTROGRAPHY 4500N Manual de usuario
FujiFilm
FujiFilm Pictrography series Manual de usuario
FujiFilm
FujiFilm ASK-300 Manual de usuario
FujiFilm
FujiFilm ApeosPort-VII 4021 Manual de usuario
FujiFilm
FujiFilm Frontier-S DX100 Manual de usuario
FujiFilm
FujiFilm Printpix NC-400D Manual de usuario
FujiFilm
FujiFilm Revoria Press SC170 Manual de usuario
FujiFilm
FujiFilm Revoria Press EC1100 Manual de usuario
FujiFilm
FujiFilm ApeosPort 2560 Manual de usuario
FujiFilm
FujiFilm Revoria Press SC180 Guía del administrador
FujiFilm
FujiFilm ASK-400 Manual de usuario
FujiFilm
FujiFilm 3000 Manual de usuario
FujiFilm
FujiFilm ApeosPro C810 Manual de usuario
FujiFilm
FujiFilm CX 3240 Manual de usuario
FujiFilm
FujiFilm ApeosPort-V 5070 Manual de usuario
FujiFilm
FujiFilm Frontier DE100 Manual de usuario
FujiFilm
FujiFilm FinePix Printer NX-500 Manual de usuario
