FRONIUS IG Plus 3.0-1 Manual de usuario

Fronius IG Plus

3.0-1 / 3.8-1 / 5.0-1 / 6.0-1 / 7.5-1

10.0-1 / 11.4-1 / 11.4-3 / 12.0-3

42,0426,0071,EA 042008

Operating Instructions

USA

Inverter for grid-connected photo-

voltaic systems

ud_fr_st_et_01382 012008

Dear Fronius Customer,

Thank you for choosing Fronius - and congratulations on your new, high-quality, high-

tech Fronius product. This introduction should provide you with general information

about the equipment. Please read it carefully to learn about the many great features of

your new Fronius product. This is the best way to get the most out of all the advantages

that it has to offer.

Please also note the safety information and the safety precautions for the product

installation location. Following all product instructions will ensure long-lasting quality and

reliability.And these are the essential ingredients for outstanding results.

Introduction

ud_fr_st_et_01382 012008

IMPORTANT SAFETY

INSTRUCTIONS

SAVE THESE INSTRUCTIONS

General This manual contains important instructions for the Fronius IG Plus, that

must be followed during installation and maintenance of the inverter.

The Fronius IG Plus is designed and tested according to international

safety requirements, but as with all electrical and electronic equipment,

certain precautions must be observed when installing and/or operating the

Fronius IG Plus.

To reduce the risk of personal injury and to ensure the safe installation

and operation of the Fronius IG Plus, you must carefully read and follow

all instructions and safety instructions in this manual.

Safety Instruc-

tions The following section “Safety Instructions“ contains different Warnings. A

Warning describes a hazard to equipment or personnel. It calls attention

to a procedure or practice, which, if not correctly performed or adhered to,

could result in damage to or destruction of part or all of the Fronius inver-

ter and/or other equipment connected to the Fronius inverter or personal

injury.

All electrical installations must be made in accordance with the National

Electrical Code, ANSI/NFPA 70, and any other codes and regulations

applicable to the installation site.

For installations in Canada the installations must be done in accordance

with applicable Canadian standards.

Electrical

installations

ud_fr_se_sv_01381 012008

Safety Instructions

DANGER!

WARNING!

CAUTION!

“NOTE“ indicates a situation which could adversely affect work results and

may cause damage to equipment.

NOTE

This equipment has been manufactured using state-of-the-art technology

and in accordance with general safety regulations. However, incorrect

operation or misuse may endanger:

- the life and well-being of the operator or third parties

- the equipment and other property of the owner/operator

- the efficient operation of the equipment.

All persons involved with equipment startup, service and maintenance must:

- be suitably qualified

- be familiar with electrical installations

- have completely read and followed these operating instructions

The operating instructions must be available at the equipment location at all

times. In addition to the operating instructions, all applicable local rules and

regulations regarding accident prevention and environmental protection must

also be followed.

General

Important

“DANGER!“ indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

“WARNING!“ indicates a potentially hazardous situation which, if not

avoided, will result in death or serious injury.

“CAUTION!“ indicates a potentially harmful situation which, if not avoided,

may result in minor and moderate injury or property damage.

“Important“ indicates practical tips and other useful information. It is not a

signal word for a harmful or dangerous situation.

Please pay special attention when one of the above symbols appears in the

manual.

ud_fr_se_sv_01381 012008 II

The equipment may only be operated in compliance with its intended use.

Any other purpose does not constitute intended use. The manufacturer is not

responsible for any damages resulting from unintended use.

Intended use also includes:

- reading and complying with all general information as well as safety

information and warnings from the operating instructions

- compliance with all inspection and maintenance requirements

- installation as per operating instructions

Where appropriate, the following guidelines should also be applied:

- Utility company regulations regarding grid feed-in

- Information from solar module manufacturer

Intended Use

All safety instructions and warning signs on the equipment itself:

- must be maintained in legible condition

- must not be damaged

- must not be removed

- must not be covered or painted over

For information about where the safety instructions and warning signs are

located on the equipment, please refer to the “General“ section of your

equipment’s operating instructions.

Any equipment malfunctions which might impair safety must be remedied

immediately before the device is turned on.

Your safety is at stake.

General

(continued)

Operation and/or storage of the device outside of the stipulated range does

not constitute intended use. The manufacturer is not responsible for any

damages resulting from unintended use.

Please refer to the technical data in your operating instructions for informati-

on about permitted ambient conditions.

Ambient Conditi-

ons

Qualified Person-

nel The service information in these operating instructions is only intended for

qualified personnel.An electrical shock can be fatal. Please do not carry out

any activities other than those referred to in the documentation even if you

are suitably qualified.

All cables and wires must be secured, undamaged, insulated and adequately

dimensioned. Loose connections, scorched, damaged or under-dimensioned

cables and wires must be repaired immediately by an authorized specialist.

ud_fr_se_sv_01381 012008

III

Maintenance and repair may only be carried out by an authorized specialist.

The use of third-party parts does not guarantee that they were designed and

manufactured according to operational demands and safety requirements.

Use only original spare parts (also applies to standard parts).

Do not carry out any alterations, installations or modifications to the device

without first obtaining the manufacturer’s permission.

Immediately replace any components that are not in perfect condition.

Qualified Person-

nel

(continued)

Safety Precauti-

ons at Equipment

Location

When installing devices with air vents, make sure that cool air can flow freely through the

vents unobstructed. The device should only be operated in accordance with the protec-

tion class listed on the rating plate.

Care must be taken during installation to ensure that there is no electromag-

netic interference with electrical and electronic equipment.

EMC Precautions

Danger of damage to electronic components due to electrostatic discharge.

Take appropriate ESD precautions when replacing and installing compon-

ents.

ESD Precautions

Electrical Installa-

tions Electrical installations may only be carried out in accordance with relevant

national and local standards and regulations.

The device should only be operated when all safety equipment is fully func-

tional. If safety equipment is not fully functional, there is a danger to:

- the life and well-being of the operator or third parties

- the equipment and other property of the owner/operator

- the efficient operation of the equipment

Safety equipment that is not fully functional must be repaired by an authori-

zed specialist before the device is turned on.

Never bypass or disable safety equipment.

Safety Precauti-

ons in Normal-

Operation

ud_fr_se_sv_01381 012008 IV

Equipment with the CE marking fulfils the basic requirements of the Guideli-

ne Governing Low-Voltage and Electromagnetic Compatibility. (For more

information, please see the attachment and/or the “Technical Data“ section in

your documentation).

Safety Markings

The user is responsible for backing up data relating to changes made to

factory settings. The manufacturer will not accept liability if personal settings

are deleted.

Data Security

The manufacturer maintains the copyright to these operating instructions.

Text and illustrations are technically correct at the time of going to print. The

right to make modifications is reserved. The contents of the operating in-

structions shall not provide the basis for any claims whatsoever on the part

of the purchaser. We would be grateful for any comments or suggestions

regarding improvements and/or error corrections for the operating instruc-

tions.

This device should not be disposed of in residential waste.

To comply with European Directive 2002/96/EC on Waste Electrical and

Electronic Equipment and its implementation as national law, electrical

equipment that has reached the end of its life must be collected separately

and returned to an approved recycling facility.Any device that you no longer

require must be returned to your dealer or you must find an approved collec-

tion and recycling facility in your area.

Ignoring this EU Directive may have adverse affects on the environment and

yourhealth.

Disposal

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de FRONIUS

FRONIUS

FRONIUS Datamanager 2.0 Manual de usuario

FRONIUS

FRONIUS SYMO Series Manual de usuario

FRONIUS

FRONIUS Primo GEN24 Manual de usuario

FRONIUS

FRONIUS Galvo Manual de servicio

FRONIUS

FRONIUS Primo 208-240 3.8-1 Manual de usuario

FRONIUS

FRONIUS Symo Manual de usuario

FRONIUS

FRONIUS Symo GEN24 3.0 Plus Manual de usuario

FRONIUS

FRONIUS Primo GEN24 Manual de usuario

FRONIUS

FRONIUS Tauro Manual de usuario

FRONIUS

FRONIUS Fronius Agilo 360.0-3 TL Manual de usuario

FRONIUS

FRONIUS Datamanager 2.0 Manual de usuario

FRONIUS

FRONIUS Primo GEN24 3.0 Manual de usuario

FRONIUS

FRONIUS Symo Manual de usuario

FRONIUS

FRONIUS Primo 3.0-1 Manual de usuario

FRONIUS

FRONIUS Rapid Shutdown Box-Duo Manual de usuario

FRONIUS

FRONIUS Galvo 208-240 1.5-1 Manual de usuario

FRONIUS

FRONIUS IG 2000 Manual de usuario

FRONIUS

FRONIUS Primo GEN24 Manual de usuario

FRONIUS

FRONIUS Primo GEN24 Manual de usuario

FRONIUS

FRONIUS FRONIUS IS 15 Manual de usuario

FRONIUS

FRONIUS IG Plus A 3.0-1 UNI Manual de usuario

FRONIUS

FRONIUS Eco 25.0-3-S Manual de usuario

FRONIUS

FRONIUS Signal Card Manual de usuario

FRONIUS

FRONIUS Symo Hybrid Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario

FRO­NIUS IG Plus 3.0-1 Manual de usuario

Manuales populares de Inversor de otras marcas

FRONIUS IG Plus 3.0-1 Manual de usuario