Frigidaire CFMV157GSA Manual de usuario

Installation

Instructions Overthe Range

Microwave Oven

IQuestions? Call 1-800-944-9044(us)

1-800-668-4606(Canada) or VisitoL,,-W_bsiteat: http://www.frigidaire.com I

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer -Be stH'eto leave these

instructions with the Consumer.

• Note to Consumer - Keet) these

instructions for future reference.

• Skill level Installation of this appliance requires

basic mechanical and electrical skills.

• Proper installation is tile responsibility of the installer.

• Product failure due to improper installation is not

covered under tile Warranty.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Instructions

CONTENTS

General information

Important Safety Instructions ........................ 3

Electrical Requirements .......................................... 3

Hood Exhaust .................................................. 4, 5

Damage - Shipment/Installation .............................. 6

Parts Induded. ......................................... 6

Tools You Will Need ............................................... 7

Mounting Space ...................................................... 7

Step-by-step installation guide

Placement of Mounting Plate ............................ 8-10

Removing the Mountirlg Plate ...................... 8

Finding tile Wall Studs .................................. 8

Determining Wall Plate Location .................. 9

Aligning the Wall Plate.. .............................. 10

Installation Types. ............................................. 11-22

[]Outside Top ............................

Exhaust 12-14

Attach Mounting Plate to Wall ............ 12

Preparation of Top Cabinet ................ 13

Checking for Proper Damper

Operation ............................................ 13

Mount the Microwave Oven ......... 13, 14

Adjust flae Exhaust Adaptor - ............. 14

Connecting Ductwork .......................... 14

[]Outside Back Exhaust 15-18

Preparing Real" Wall for

Outside Back Exhaust .......................... 15

Remove Exhaust Adaptor .... .................. 15

Attach Mounting Plate to Wall .......... 16

Preparation of Top Cabinet .............. 16

Adapting Microwave Blower

for OutsMe Back Exhaust ................ 16, 17

Mount the Microwave Oven .............. 18

[] Recilvulating ........................................ 19-22

Attach Mourning Plate m Wall ............ 19

Preparation of Top Cabinet ................ 19

Check Microwave Assembly ................ 20

Adapting Microwave Blower

for Recirculation .......................... 20, 21

Mount the Microwave Oven .......... 21, 22

Installing tile Charcoal Filter .............. 22

Before You Use Your Microwave .......................... 23

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.

The installer nmst perform a ground continuity check

on the power outlet box before beginning the

installation to insure that the outlet box is properly

grounded. If not properly grounded, or if the outlet

box does not meet electrical requirements noted

(under ELECTRICAL REQUIREMENTS), a qualified

electrician should be employed to correct any

deficiencies.

CAUTION: For personal

safety, remove house fuse

or open circuit breaker

before beginning

installation to avoid severe

or fatal shock injury.

CAUTION: For personal safety, the mounting surface

must be capable of supporting the cabinet load, in

addition to the added weight of this 63-85 pound

(28.5-38.5 kg) product, plus additional oven loads of

up to 50 pounds (22.7 kg) or atotal weight of

113-135 pounds (51.3-61.2 kg).

CAUTION: For personal safety, this product cannot

be installed in cabinet arrangements such as an island or

a peninsula. It must be mounted to BOTH a top cabinet

AND a wall.

NOTE: For easier installation and personal safety, it is

recommended that two people install this product.

IMPORTANT - PLEASE READ CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

The power cord of this

appliance is equipped with a

three-prong (grounding)

plug which mates with a

standard three-prong

(grounding) wall receptacle

to minimize the possibility

of electric shock hazard

from this appliance.

Ensureproper

groundexists

beforeuse

You should have the wall receptacle and circuit checked

by a qualified electrician to make sure the receptacle is

properly grounded.

Where a standard two-prong wall receptacle is

encountered, it is very important to have it replaced

with a properly grounded three-prong wall receptacle,

installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN EXTENSION CORD.

ELECTRICAL

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 15 amps and

1.6 kilowatts. This product must be connected to a

supply circuit of the proper voltage and fl'equency.

Wire size must conform to the requirements of the

National Electrical Code or the prevailing local

code for this kilowatt rating. The power supply

cord and plug should be brought to a separate

15- to 20- ampere branch circuit single grounded

outlet. The outlet box should be located in the

cabinet above the microwave oven. The outlet box

and supply circuit should be installed by a qualified

electrician and conform to the National Electrical

Code or the prevailing local code.

Installation Instructions

HOOD EXHAUST

NOTE: Read these next two pages only if you plan to vent your exhaust to the

outside. If you plan to recirculate the air back into the room, proceed to page 6.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible

ductwork installation.

DUCT PIECES

RoofCap

12Ft,(3,6m)StraightDuct

(6"/15,2cmRound)

EQUIVALENT NUMBER

LENGTH x USED

Rectangular-to-Round

TransitionAdaptor*

24Ft,(7,3m) x (1)

12Ft,(3,6m) x (1)

5Ft, (1,5 m) x

Equivalent lengths of duct pieces are basedon actual tests and

reflect requirements for good venting performance with any vent hood,

(1)

Total Length =

EQUIVALENT

LENGTH

24Ft,(7,3m)

12Ft,(3,6m)

5Ft,(1,5m)

41 Ft. (12.5 m)

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible

ductwork installation.

DUCT PIECES

EQUIVALENT NUMBER EQUIVALENT

LENGTH* x USED =LENGTH

Wall Cap 40 Ft, (12,2 m) x (1) 40 Ft, (12,2 m)

3 Ft,StraightDuct

31/4"x10'78,2x25,4cm

Rectangular)

90° Elbow

3 Ft,(0,9m)

10 Ft, (3 m)

(1)

(2)

3 Ft,(0,9m)

20Ft,(3m)

Equivalent lengths of duct pieces are based on actual tests and

reflect requirements for good venting performance with any vent hood, Total Length = 63 Ft. (19.2 m)

NOTE: For back exhaust, care shouM be taken to align exhaust with space between studs, oi" wall shouM be prepared

at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

Installation Instructions

NOTE: If you need to install ducts, note that the total

duct length of 31/4" x 10" (8.2 x 25.4 cm) rectangular or

6" (15.2 cm) diameter round duct should not exceed

120 equivalent feet (36.5 m).

Outside ventilation requires a HOOD EXHAUST DUCT.

Read the following carefully.

NOTE: It is important that venting be installed using

the most direct route and with as few elbows as possible.

This ensures cleat" venting of exhaust and helps prevent

blockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate with

a standard 31/4" x 10" (8.2 x 25.4 cm) rectangular duct.

If a round duct is required, a rectangular-to-round

transition adaptor nmst be used. Do not use less than

a 6" (15.2 em) diameter duct.

Maximum duct length:

For satisfactory air movement, the total duct length of

3l/4" x 10" (8.2 x 25.4 cm) rectangular or 6" (15.2 cm)

diameter round duct should not exceed 120 equivalent

feet (36.5 m).

Elbows, transitions, wall and roof caps,

etc., present additional resistance to airflow and are

equivalent to a section of straight duct which is longer

than their actual physical size. When calculating the total

duct length, add the equivalent lengths of all transitions

and adaptors plus the length of all straight duct sections.

The chart below shows you how to calculate total

equivalent ductwork length using the al)t)roximate feet

of equivalent length of some typical ducts.

DUCT PIECES

Rectangular-to-Round

TransitionAdaptor*

Wall Cap

90° Elbow

45° Elbow

90° Elbow

45° Elbow

RoofCap

StraightDuct6" (15,2cm)

Roundor 374"x 10"

(8,2x25,4cm)Rectangular

EQUIVALENT NUMBER

LENGTH x USED

5 Ft, (1,5 m)

40Ft,(12,2m)

10 Ft,(3m)

5 Ft, (1,5 m)

25 Ft,(7,6 m)

5 Ft, (1,5 m)

24 Ft,(7,3m)

I Ft,(0,3m)

x ()

Total Ductwork

EQUIVALENT

LENGTH

Ft,or m

Ft. or m

*IMPORTANT: If a rectangular to round transition

adaptor is used, the bottom corners of tbe dan]per

will bave to be cut to fit, using tbe tit] snips, in order

to allow Dee movement of tbe dan]per.

Equivalent lengths of duct pieces are based on actual tests

and reflect requirements for good venting performance wit[]

any vent hood.

Installation Instructions

DAMAGEmSHIPMENT/

INSTALLATION

• If the unit is damaged in shipment, return the

unit to the store in which it was bought for repair

or replacement.

• If the unit is damaged by the customer, repair or

replacement is the responsibility of tile customer.

• If the unit is damaged by the installer (if other

than the customer), repair or replacement nmst

be made by arrangement between customer

and installer.

PARTS INCLUDED

HARDWARE PACKET

PART QUANTITY

Wood Screws 2

(1/;,x 2")

ToggleBolts (and 4

wing nuts) (Sk6"x 3")

Self-Aligning Machine 3

Screws (1/4"-28x 31/4'')

Nylon Grommet 2

(for metal cabinets)

Power CordStrap 1

(plastic)

You will find the installation hardware contained in

a packet with the unit. Check to make sure you have

all these parts.

NOTE: Some extra parts are included.

PARTS INCLUDED (coNT.)

ADDITIONAL PARTS

PART

TOPCABINETTEMPLATE

REAR

WALL

TEMPLATE

TopCabinet

Template

RearWall

Template

Installation

Instructions

Separately

Packed

Grease

Filters

QUANTITY

Installation Instructions

TOOLS YOU WILL NEED

# 1Phillipsscrewdriver

Tinsnips(forcutting

damper,if required)

Gloves

Safetygoggles

Pencil

Scissors

(tocuttemplate,if necessary)

Saw(saber,holeor keyhole)

Rulerortapemeasureand

t edge

Electricdrill with skd',Y2"and%"

drill bits

Studfinder or Hammer(optional)

Level

Carpentersquare

(optional)

Fillerblocksor scrap

woodpieces,if needed

Fortop cabinetspacing

(usedonrecessedbottom

cabinetinstallationsonly)

Duct and masking tape

MOUNTING SPACE

66" (167.6cm)

or Morefrom

the Floorto the

Topof the

Microwave

BottomEdgeof

CabinetNeedsto

30" (76.2cm)

or Morefrom the

CookingSurface

IBacksplash

NOTES:

• The space between the cabinets must be

30" (76.2 cm)wide and flee of obstructions.

• If you are going to vent your microwave oven

to the outside, see Hood Exhaust Section for

exhaust duct preparation.

• When installing the microwave oven beneath

smooth, fiat cabinets, be careful to follow the

instructions on the top cabinet template for

power cord clearance.

Installation Instructions

PLACEMENT OF THE MOUNTING PLATE

I-_ REMOVING THE MICROWAVE

OVEN FROM THE CARTON/

REMOVING THE MOUNTING

PLATE

[]Remove the installation instructions, filters, glass

tray and the small hardware bag. Do not remove

the Styrofoam protecting the fl'ont of the oven.

[]Fold back all 4 carton flaps fully against carton

sides. Then carefully roll the oven and carton over

onto the top side. The oven should be resting in

the Styrofoam.

[Pull the carton up and off the oven.

[]Remove and properly discard plastic bags.

Screws----__ Mounting

Plate T

[]Remove the screws from the mounting plate.

This plate will be used as the rear wall template

and for mounting. Reinstall the screws into the

holes where they were removed.

I-_ FINDING THE WALL STUDS

]Find the studs, using one of the following

methods:

A. Stud finder - a magnetic device which

locates nails.

B. Use a hammer to tap lightly across the

mounting surface to find a solid sound.

This will indicate a stud location.

[] After locating the stud(s), find the center by

probing the wall with a small nail to find the edges

of the stud. Then place a mark halfway between

the edges. The center of any adjacent studs should

be 16" (40.6 cm) or 24" (61 cm) fi'oln this mark.

[]Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO

AT LEAST ONE WALL STUD.

Installation Instructions

I-_ DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Plate positionmbeneath flat bottom

cabinet Plate positionmbeneath framed recessed

cabinet bottom

Mounting Plate Tabs

g the Cabinet Bottom MountingPlateTabs

Touchingthe BackFrame

At least 30" (76.2 cm),

up to 36" (91,4 cm)

30"(76.2cm)

to Cooktop

Plate position_beneath recessed bottom

cabinet with front overhang

MountingPlatewith

TabsBelowCabinet

Bottomthe Same

Distanceasthe Front

OverhangDepth

30"(76.2 cm)

toCooktop

Your cabinets may have decorative trim that

interferes with the microwave installation. Remove

the decorative trim to install the microwave properly

and to make it level.

THE MICROWAVE MUST BE LEVEL.

Use a level to make sure the cabinet bottom is level.

If the cabinets have a fl'ont overhang only, with no

back or side fl'ame, install the mounting plate down

the same distance as the fl'ont overhang depth. This

will kee t) the microwave level.

[]Measure the inside depth of the fl'ont overhang.

[]Draw a horizontal line on the back wall an equal

distance below the cabinet bottom as the inside

depth of the fl'ont overhang.

[] For this type of installation with fl'ont overhang only,

align the mounting tabs with this horizontal line, not

touching the cabinet bottom as described in Step D.

Installation Instructions

ALIGNING THE WALL PLATE

, I

j_-_ DrawaVertical

j LineonWall I/I

I fromCenterof [/I

Centerlinej TopCabinet I//

Notches j I//

,,................

CAUTION: _ t

to avoid cuttil HoleC AreaE

sharp edges.

HoleD

_Draw a vertical line on the wall at the center of the

30" (76.2 cm) wide space.

_Use the mounting plate as the template for the rear

wall. Place the mounting plate on the wall, making

sure that the tabs are touching the bottom of the

cabinet or the level line drawn in Step C for cabinets

with front overhang. Line up the notch and centerline

on the bottom of the mounting plate to the centerline

on the wall.

_ While holding the mounting plate with one hand,

draw circles on the wall at holes A, B, C and D

(see illustration above/actual plate marked with

an'ows). Four holes must be used for mounting.

[]

NOTE: If neither C nor Dis in a stud, find a stud

somewhere in area E and draw a fifth circle to line up

with the stud. It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave.

Set the mounting plate aside.

Drill holes on the circles. If there is a stud, drill a 3A(;"

hole for wood screws. For holes that don't line up with

a stud, drill a %" hole for toggle bolts.

NOTE: DO NOT MOUNT THE PLATE AT

THIS TIME.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microondas de Frigidaire

Frigidaire

Frigidaire GLMB186K Manual de usuario

Frigidaire

Frigidaire FFMV152CL W Instrucciones de funcionamiento y seguridad

Frigidaire

Frigidaire FGMV205KB Manual de usuario

Frigidaire

Frigidaire FGMV155CTF Manual de usuario

Frigidaire

Frigidaire MWV150K Manual de usuario

Frigidaire

Frigidaire FGMC3065KW - Microwave Oven Combination Guía de inicio rápido

Frigidaire

Frigidaire FGMV173KQ - Gallery Series Microwave Guía de inicio rápido

Frigidaire

Frigidaire FGBM185KB - Microwave Manual de servicio

Frigidaire

Frigidaire CPLMZ169GCC Manual de usuario

Frigidaire

Frigidaire FPMC3085K F Guía de instalación

Frigidaire

Frigidaire GLMB186 Manual de usuario

Frigidaire

Frigidaire FMV156E Manual de instrucciones

Frigidaire

Frigidaire MC-700M Guía de referencia rápida

Frigidaire

Frigidaire FGMC2765KB - Gallery 27" Microwave Combination... Manual de usuario

Frigidaire

Frigidaire FFMV162LSA Manual de usuario

Frigidaire

Frigidaire FFCE1431LB Manual de usuario

Frigidaire

Frigidaire FPMO209KF - Professional 2.0 cu. Ft.... Manual de usuario

Frigidaire

Frigidaire FGMV185KB - Gallery 1.8 cu. Ft. Microwave Manual de usuario

Frigidaire

Frigidaire CFCM0934NW Manual del propietario

Frigidaire

Frigidaire 316495064 Manual de usuario

Frigidaire

Frigidaire FPBM189KF - Professional Series... Manual de usuario

Frigidaire

Frigidaire GLEB27M9FQA Manual de usuario

Frigidaire

Frigidaire Gallery GMOS1964AD Manual de usuario

Frigidaire

Frigidaire FPBM307NTF Manual de usuario

Manuales populares de Microondas de otras marcas

Daewoo

Daewoo KOG-574R0S Manual de usuario

LG MH7040SS Manual de usuario

Sharp

Sharp R-895(AL)M Manual de usuario

Dometic

Dometic DOTRM13W Manual de usuario

Sanyo

Sanyo EM-X680 Manual de usuario

Sharp

Sharp R-393M Manual de usuario

KitchenAid

KitchenAid KMCX4510 Instrucciones de instalación

Smeg

Smeg S45MCX1 Manual de usuario

Russell Hobbs

Russell Hobbs RHM2044 Manual de usuario

Sunbeam

Sunbeam SMW759 Manual de usuario

Gallet

Gallet FMOE230S Manual de usuario

Bosch

Bosch CEG732X.1B Manual de usuario

Dometic

Dometic Roadmate 230 Manual de usuario

Samsung

Samsung SJ0396W Manual de usuario

Sanyo

Sanyo EM-P494WS Manual de usuario

Sharp

Sharp R-240 Manual de usuario

Electrolux

Electrolux EMS2840 Manual de usuario

Daewoo

Daewoo KOC-984T2S13 Manual de usuario