Freescale Semiconductor MPC8572E Manual de usuario

Freescale Semiconductor

About this Document

This document describes how to connect to the

MPC8572EAMC and verify its basic operation. Settings for

the switches and jumpers are shown, as well as instruction

for connecting peripheral devices. In addition, instructions

for connecting a debugger to the MPC8572EAMC, such as

Freescale’s CodeWarrior are included, but instructions for

working with this debugger are beyond the scope of this

document.

Required Reading

It is assumed that the reader is familiar with the MPC8572E

microprocessor and MPC8572E PowerQUICC™ III

Integrated Host Processor Family Reference Manual as well

as the content of the High Level Design Document for

MPC8572EAMC.

Document Number: MPC8572EAMCGSG

Rev. 1.0, 08/2008

Contents

1. Check Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Assemble and Connect the Board . . . . . . . . . . . . . . . . 6

3. Perform Initial Board Power Up and Check LEDs . . . 6

4. Connecting JTAG Debugging Tools to the Board . . . 8

5. Front Panel Connectivity . . . . . . . . . . . . . . . . . . . . . . 8

6. Module Management Support . . . . . . . . . . . . . . . . . . 9

7. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

MPC8572E Advanced Mezzanine Card

Hardware Getting Started Guide

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

2Freescale Semiconductor

Definitions, Acronyms, and Abbreviations

Table 1. Definitions, Acronyms, and Abbreviations

AdvancedMC Advanced mezzanine card

AMC Advanced mezzanine card

ATCA Advanced telecommunications computing platform

BDM Background debugging mode

CCB Core complex bus

COP Computer operating properly

CPLD Complex programmable logic device

DIP Dual in-line package

DSP Digital signal processor

DUART Dual universal asynchronous receive transmit

EEPROM Electrically erasable programmable read-only module

GETH Gigabit Ethernet

HW Hardware

I2C (bus) Inter-IC bus

MMC Module management controller

SRIO Serial RapidIO

UART Universal asynchronous receive transmit

USB Universal serial bus

μTCA micro telecommunications computing architecture

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

Freescale Semiconductor 3

Check Switches

Figure 1 illustrates the main header and switch locations on the top (processor) side of the

MPC8572EAMC. Users should follow this getting started guide prior to applying power to the card,

because incorrect board settings can cause permanent board damage.

Figure 1. MPC8572EAMC Primary Side Header Positions

1 Check Switches

1. DIP Switch settings should only be changed when power is NOT applied to the board.

2. The MPC8572EAMC board has three push button switches (SW1, SW2 and SW3), four Dual In

line Package (DIP) switches (SW4, SW5, SW500, and SW501), and eight jumper headers (J1–J7

and HD1). The default DIP switch positions provide Power On Reset configuration values for the

MPC8572EAMC board. Check the default positions and verify the board is operational before

changing the switches. The settings for the switches are shown in Figure 2, with their default

positions as described in Table 2. Table 6 gives a full list of all possible switch configurations.

3. Jumper headers J3, J6, and HD1 are reserved for factory test and are used to program the module

management controller and Reset/System CPLDs. Users should not attempt to reprogram the card

using these headers because this may result in permanent card damage. The jumpers should

remain in their default position as detailed in Table 3.

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

4Freescale Semiconductor

Check Switches

Figure 2. Secondary Side Switch Positions

Table 2. Default Switch Settings

Feature Default Settings

[OFF = 1, ON = 0) Comments

SW4

SW4.1 OFF Reserved

SW4.2 OFF Reserved

SW4.3 OFF Reserved

SW4.4 ON [SW4.4] = MMC H/W Select. ON—MMC present

SW5

SW5.1 ON [SW5.1:2] = ON:OFF. CCB:SYSCLK = 10:1 (666 MHz)

SW5.2 OFF

SW5.3 OFF [SW5.3:4] = OFF:ON. e500 Core #0:CCB = 2:1

SW5.4 ON

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

Freescale Semiconductor 5

Check Switches

SW5.5 OFF [SW5.5:6] = OFF:ON. e500 Core #1:CCB = 2:1

SW5.6 ON

SW5.7 OFF [SW5.7:8] = OFF:OFF. Boot ROM Location = 32-bit Local FLASH Memory

SW5.8 OFF

SW500

SW500.1 ON [SW500.1:3]=ON:ON:OFF.DDR Clock Ratio = 10:1 DDRCLK (666 MHz)

SW500.2 ON

SW500.3 OFF

SW500.4 OFF [SW500.4:5] = OFF:OFF. MPC8572E acts as the host processor

SW500.5 OFF

SW500.6 ON [SW500.6:8] = ON:ON:OFF. IO Port Selection = SRIO 125 MHz, 3.125 Gbps (x4)

SW500.7 ON

SW500.8 OFF

SW501

SW501.1 OFF [SW501.1] = OFF Boot Sequence Configuration = Boot Sequencer Disabled

SW501.2 OFF CPU Boot Config:

[SW501.2:3] = OFF:ON. E500 Core 0 allowed to boot, Core 1 in boot hold-off

SW501.3 ON

SW501.4 ON RIO System Size:

[SW501.4] = ON. Large system size, up to 65,536 devices

Table 3. Header Configuration/Availability

Feature Status Comments

J1 Available IEEE Std 1588™ header

J2 Available USB DUART Connection. Provides debug information from MPC8572E Core #0 /1.

J3 — MMC BDM Debug header. Reserved for factory use only.

J4 Available COP Debug Header

J6 — CPLD JTAG Select. Reserved for factory use only.

J7 Available Pin 1 = TxD, Pin 2 = RxD, Pin 3 = GND. Connect for console debug information from MMC only.

HD1 — CPLD Programming Header. Reserved for factory use only.

Table 2. Default Switch Settings (continued)

Feature Default Settings

[OFF = 1, ON = 0) Comments

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

6Freescale Semiconductor

Assemble and Connect the Board

2 Assemble and Connect the Board

1. The heat sink must be fitted to the processor at all times.

2. Freescale recommends running the AdvancedMC in an ATCA, microTCA, picoTCA chassis or

equivalent. This delivers the correct power and air flow to the board. The board should be inserted

into the carrier chassis as per the specific carrier instructions. Please ensure the card is inserted the

correct way. An example is shown in Figure 3.

Figure 3. Inserting the MPC8572EAMC into a Chassis

3 Perform Initial Board Power Up and Check LEDs

A complete list of all LEDs on the MPC8572EAMC is shown in Table 5.

1. Switch on the power to the chassis.

2. Check for the blue front panel LED and power good LEDs being illuminated (a full description of

the LED operation is given in Table 5).

Table 4. Push Switches

Feature Switch Function Comments

SW1 AdvancedMC hot swap Micro switch used to detect AdvancedMC handle position

SW2 Power cycle switch Push button switch used to power cycle the AdvancedMC

SW3 Reset switch Push button switch used for hard reset of the processor

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

Freescale Semiconductor 7

Perform Initial Board Power Up and Check LEDs

3. When powered up:

a) Blue front panel LED remains illuminated as long as power is applied to the board (via the

AdvancedMC backplane connector).

b) Ethernet port activity LEDs switch on to indicate any Ethernet link to the front or back planes.

c) The “System Status” LED, LD507, switches on, then goes off once system configuration is

complete. LED LD506 should stay on indicating the processor is “Ready.”

d) Any USB UART activity is shown on LEDs D507 and D508.

4. Pressing the power cycle button (SW2) power cycles the board and start the reset sequence.

5. Pressing the reset button (SW3) starts the reset sequence only.

Table 5. LED Operation

Description Ref Color LED On LED Off

MMC red LED LD1 Red MMC control Normal operation

MMC card power blue LED LD500 Blue Hot swap state Hot swap state

Port 0 AMC SERDES Ethernet Rx activity D500 Green Rx Ethernet activity No Rx Ethernet activity

Port 0 AMC SERDES Ethernet Tx activity D501 Yellow Tx Ethernet activity No Tx Ethernet activity

Port 0 AMC SERDES LOS D502 Orange Loss of signal No loss of signal

Port 1 AMC SERDES LOS D504 Orange Loss of signal No loss of signal

Port 1 AMC SERDES Ethernet Tx activity D505 Yellow Tx Ethernet activity No Tx Ethernet activity

Port 1 AMC SERDES Ethernet Rx activity D506 Green Rx Ethernet activity No Rx Ethernet activity

USB/UART 1 activity D507 Orange UART 1 activity No UART 1 activity

USB/UART 0 activity D508 Orange UART 0 activity No UART 0 activity

Front panel dual RJ45 Ethernet Rx activity P3:D1-2a Green Rx Ethernet activity No Rx Ethernet activity

Front panel dual RJ45 Ethernet Tx activity P3:D1-4a Yellow Tx Ethernet activity No Tx Ethernet activity

Front panel dual RJ45 Ethernet Rx activity P3:D1-2b Green Rx Ethernet activity No Rx Ethernet activity

Front panel dual RJ45 Ethernet Tx activity P3:D1-4b Yellow Tx Ethernet activity No Tx Ethernet activity

Front panel 10/100 RJ45 Ethernet Rx activity P1 Orange/

Green

Rx Ethernet activity No Rx Ethernet activity

Front panel 10/100 RJ45 Ethernet Tx activity P1 Yellow Tx Ethernet activity No Tx Ethernet activity

General debug system CPLD LD507 Green System CPLD

execution not

complete

System CPLD execution

complete

General debug system CPLD LD506 Green Ready signal POR config cycles

unsuccessful

General debug system CPLD LD505 Yellow Default on User debug #1

General debug system CPLD LD504 Yellow Default on User debug #2

General debug POR CPLD LD502 Green User config #1 User config #1

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

8Freescale Semiconductor

Connecting JTAG Debugging Tools to the Board

4 Connecting JTAG Debugging Tools to the Board

Figure 4 illustrates an example of how to connect a JTAG debugger to the MPC8572EAMC. The USB tap

debugging tool enables the CodeWarrior software IDE to work with the MPC8572EAMC board.

1. Connect the JTAG debugger unit to the JTAG 16-pin connector (J4).

2. Connect USB cable from Host PC (with CodeWarrior Power Architecture™ tools installed on it)

to CodeWarrior USB Tap. Figure 4 illustrates Freescale’s CodeWarrior debugger connected to the

MPC8572EAMC. Note the orientation of pin 1 (red edge of ribbon cable) with pin 1 on J4.

3. Switch on power to the board.

4. Check for completion of the reset sequence (see step 3) and power indicator on USB Tap.

5. Continue as per standard CodeWarrior instructions.

a) Contact your local FAE for the correct JTAG configuration file.

Figure 4. USB TAP Connection to Header J4

5 Front Panel Connectivity

Figure 5 shows the different front panel connections. P1 provides a RJ45 10/100 Ethernet port. The final

front panel connector P3 provides two high speed Gigabit Ethernet connections. Serial connectivity for

General debug POR CPLD LD501 Yellow User config #2 User config #2

General debug POR CPLD LD503 Yellow User config #3 User config #3

Table 5. LED Operation (continued)

Description Ref Color LED On LED Off

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

Freescale Semiconductor 9

Module Management Support

both dual cores is provided via USB serial connector J2. Users should note that USB drivers should be

installed onto the host PC before the serial terminal can be used. These can be downloaded from the

following URL: http://www.ftdichip.com/FTDrivers.htm

A serial terminal can be setup using a PC communication program such as Hyperterminal set to 115200

baud rate. If the USB session hangs the terminal then the communication link must be disconnected and

then reconnected.

Any board settings that users wish to make should be checked for validity against a recent version of the

MPC8572E PowerQUICC™ III Integrated Host Processor Family Reference Manual. Operating the

board, or MPC8572E device, beyond the recommended device operating conditions may cause permanent

board damage.

Figure 5. MPC8572EAMC Front Panel Connectivity

6 Module Management Support

The MPC8572EAMC contains a CorEdge™-enabled module management controller (MMC), which

meets the PICMG and intelligent platform management interface (IPMI) AdvancedMC specifications.

This enables the board to be hot swapped in or out of an MMC-compatible system. To hot swap a board,

complete the following steps:

Hot swapping in a board:

1. Set switch SW4.4 to ON to select the MMC present option.

MPC8572E Advanced Mezzanine Card Hardware Getting Started Guide, Rev. 1.0

10 Freescale Semiconductor

Module Management Support

2. Insert the AdvancedMC into the slot with the handle extracted. The BLUE LED switches ON once

it is inserted.

3. Close the handle. The BLUE LED flashes and then switches OFF. The board powers up.

Hot swapping out a board:

1. Extract the hot swap handle

2. The BLUE LED flashes and then stays ON.

3. When the BLUE LED is ON, the AdvancedMC can be removed from the chassis.

Figure 6. Hot Swapping in a Chassis

NOTE

While the chassis shown in Figure 6is MMC-compatible, thechassisshown

in Figure 3 is not.

Table 6 lists the complete switch settings.

Table 6. Complete Switch Settings

Feature Default Settings

[OFF = 1, ON = 0) Comments

SW4

SW4.1 OFF Reserved

SW4.2 OFF Reserved

SW4.3 OFF Reserved

SW4.4 ON [SW4.4] = MMC H/W Select. ON—MMC present1

[SW4.4] = MMC H/W Select. OFF—MMC not present

Tabla de contenidos

Otros manuales de Placa madre de Freescale Semiconductor

Freescale Semiconductor

Freescale Semiconductor DEMO908QB8 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor M68EVB912C32 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor USB-KW40Z Manual de usuario

Freescale Semiconductor

Freescale Semiconductor Qorivva MPC5746R-176DS Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MC13892 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MPC8260-TCOM Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MSC8156 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor kinetis TWR-SMPS-LVFB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MPC566EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor FRDM-KL46Z Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MED-SPI Manual de usuario

Freescale Semiconductor

Freescale Semiconductor T4240RDB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor FRDM-KL27Z Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33912EVME Manual

Freescale Semiconductor

Freescale Semiconductor i.MX 6SoloLite Linux Manual de usuario

Freescale Semiconductor

Freescale Semiconductor FRDM-KL25Z Manual de usuario

Freescale Semiconductor

Freescale Semiconductor M68HC12A4EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33882EKEVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor M54455EVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor i.MX 6UltraLite Manual de instalación

Freescale Semiconductor

Freescale Semiconductor KIT22XS4200EKEVB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor DEMO908GZ60 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor CSM-56F801 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33816AEEVM Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario