Freescale Semiconductor MPC8260-TCOM Manual de usuario

3/1999

Rev 1.0

MPC8260 PowerQUICC II

MPC8260-TCOM User’s Manual

MOTOROLA

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC8260TCOM User’s Manual PRELIMINARY

0•1 INTRODUCTION

This page provides unpacking instructions, hardware preparation, and installation instructions for the

MPC8260TCOM.

0•2 UNPACKING INSTRUCTIONS

NOTE

If the shipping carton is damaged upon receipt,

request carrier’s agent be present during

unpacking and inspection of equipment.

Unpack equipment from shipping carton. Refer to packing list and verify that all items are present. Save

packing material for storing and reshipping of equipment.

CAUTION

AVOID TOUCHING AREAS OF INTEGRATED

CIRCUITRY; STATIC DISCHARGE CAN

DAMAGE CIRCUITS.

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

PRELIMINARY MPC8260TCOM User’s Manual

GENERAL INFORMATION

CHAPTER 1 - GENERAL INFORMATION

1•1 INTRODUCTION

This manual provides general information, preparation for use and installation instructions, operating

instructions, functional description, and support information for the MPC8260TCOM board.

1•2 FEATURES

The main features of the MPC8260TCOM board are as follows:

• Two Fast Ethernet channels connected guilelessly to the Level One LXT970 device.

• The 2 Fast-Ethernet use FCC1 and FCC3.

• Each one of the Fast - Ethernet module can be disable/disable and controlled by SW.

• Two DS3 channels using the TRAN-SWITCH TXC-03401 FRAMER and TRAN-SWITCH TXC-

20153G DS3 Line Interface Module.

• Each one of the DS3 framer controlled via the MPC8260.

• The 2XDS3 use the TDMA1(DS3_1 FCC2) and TDMA2 (DS3_2 FCC3).

• Each one of the DS3 module can be disable/enable by HW.

• Eight T1 interfaces using MCC1 and MCC2.

• The 8 x T1 use the TOCTL PM4388 as a framer and 2 x PM4314 as a line interface module, both

controlled by the MPC8260.

• Each one of the eight T1 can be independently configured, monitor, isolated and controlled by

SW.

• The TOCTL (PM4388) is controlled by the MPC8260 via the address and data bus.

• The MPC8260TCOM board is powered and controlled by the MPC8260ADS via 2 x 128pin DIN

connectors.

1•3 SPECIFICATIONS

The MPC8260TCOM specifications are given in Table 1-1.

Table 1-1 MPC860SAR-PHY Speciﬁcations

CHARACTERISTICS SPECIFICATIONS

Power requirements (no other boards attached) +5Vdc @ 2 A (typical), 2.5 A (maximum)

Operating temperature 0 degrees to 30 degrees C ambient air temperature

Storage temperature -25 degrees to 85 degrees C

Relative humidity 5% to 90% (non-condensing)

Dimensions

Height

Depth

Thickness

9.17 inches (233 mm)

6.3 inches (160 mm)

0.063 inches (1.6 mm)

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC8260TCOM User’s Manual PRELIMINARY

GENERAL INFORMATION

1•4 GENERAL DESCRIPTION

The MPC8260TCOM Board includes the following modules: 8 x T1/E1, 2 x Fast Ethernet, 2 x DS3.

The MPC8260ADS includes the following modules: ATM155 and Fast Ethernet.

Both MPC8260TCOM and MPC8260ADS implements the following network for H/W & S/W development

applications:

ATM155M (FCC1 on MPC8260ADS) + 8 x T1 (MCC1 & MCC2),

ATM155M (FCC1 on MPC8260ADS) + 2 x Fast Ethernet (FCC2 on MPC8260ADS, FCC3),

ATM155M (FCC1 on MPC8260ADS) + 2 x DS3 (TDMa1 to FCC2, TDMa2 to FCC3),

3 x Fast Ethernet (FCC2 on MPC8260ADS, FCC1, FCC3).

NOTE: Some modules share the same GPIO. Care must be taken when configuring each one of the

modules, to prevent a conflict between them. Before operating the board the user should define the modes

of operation and configure the MPC8260 GPIO to the corresponding module.

Special care must be taken when using the Fast Ethernet interfaces. It do not have a h/w enable

signal, it is configured only through the MII MDC,MDIO signals.

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

PRELIMINARY MPC8260TCOM User’s Manual

GENERAL INFORMATION

1•5 RELATED DOCUMENTATION

The following publications are applicable to the MPC8260TCOM and may provide additional helpful

information.

• MPC8260 Spec.

• MPC-SIERRA TOCTL PM4388. (http://www.pmc-sierra.com/register/toctl.asp#D)

• MPC-SIERRA QDSX PM4314. (http://www.pmc-sierra.com/register/qdsx.asp#D)

• Level-One LXT970 Fast - Ethernet Transceiver. (http://www.level1.com/product/qa/

lxt970qa.html)

• TRAN-SWITCH TXC-03401 DS3 FRAMER. (http://www.transwitch.com/pdh.html#ds3f)

• TRANS-SWITCH TXC20153G DS3 Line Interface Module. (http://www.transwitch.com/

pdh.html#limsn)

• TRANS-SWITCH TXC020020 DS3 Line Interface Device. (http://www.transwitch.com/pdh.html#)

1•6 ABBREVIATIONS USED IN THE DOCUMENT

• FCC - Fast serial Communication Controller.

• MCC - Multi Channel Controller.

• FE - Fast Ethernet.

• TOCTL - PMC-Sierra framer PM4388.

• LIU - Line interface module.

• QDSX - PMC-sierra LIU PM4314.

• DS3 - Serial communication of 44.736Mbps.

• DS3F - DS3 Framer.

• TCOM - MPC8260TCOM Board

• GPIO - General Purpose I/O related to the MPC8260 PORTS.

• ADS - MPC8260ADS

• Module - Each one of the options this board can give: 8 x T1, 2 x FE, 2 x DS3.

• CPM - Communication Processor Module.

• SPEC - Engineering Speciﬁcation document.

1•7 REQUIRED EQUIPMENT

The MPC8260TCOM operates only with the MPC8260ADS.

The equipment required to connect the communication lines to the two cards is described bellow:

• The RJ45 connectors are separated to two groups:

• 8 x E1/T1 circuit connected by a 8 wires cable.

• 2 x Fast Ethernet circuit connected by a 8 wires cable.

• 4 x BNC 75Ωdedicated to 2 x DS3 circuit connected by a BNC cable. (2 - receive, 2 - transmit)

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC8260TCOM User’s Manual PRELIMINARY

GENERAL INFORMATION

FIGURE 1-1 MPC8260TCOM Connections.

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

PRELIMINARY MPC8260TCOM User’s Manual

SOFTWARE AND HARDWARE PREPARATION

CHAPTER 2 - SOFTWARE AND HARDWARE PREPARATION

2•1 SOFTWARE PREPARATION

The TCOM is not a stand alone board. It should be connected to the MPC8260ADS. To select the desired

configuration and ensure proper operation of the MPC8260TCOM board, changes in the MPC8260 GPIO

configuration may be required. The following table describes the different configurations of all the modules

on the board. NOTE:

The FE modules have no H/W protection. Before using one of the FE module make sure that other modules

using the same GPIO are disabled. The following table shows the various types of communication

channels that can be implemented by connecting the TCOM & ADS cards.

The I/O are related to the MPC8260.

The dark column are the modules on the ADS.

Table 2: Ports Function Signals

Ports/name T1

ADS

ATM8

FCC1

ADS

FE 0

FCC2

FCC3

TDM1

DS3

FCC2

TDM2

DS3

FCC3

PA2/DS3-TXCLK/TDMD2-TXCLK(clock20) I I

PA6/DS3-RXSYNC/TDMA1-L1RSYNC II

PA7/DS3-TXSYNC/TDMA1-L1TSYNC II

PA8/DS3-RXD0/TDMA1-L1RXD0 II

PA9/DS3-TXD0/TDMA1-L1TXD0 OO

PA14/MIIRXD3/ATM8-RXD4 II

PA15//MIIRXD2/ATM8-RXD5II

PA16/MIIRXD1/ATM8-RXD6 II

PA17/MIIRXD0/ATM8-RXD7II

PA18/MIITXD0/ATM8-TXD7 OO

PA19/MIITXD1/ATM8-TXD6OO

PA20/MIITXD2/ATM8-TXD5OO

PA21/MIITXD3/ATM8--TXD4 OO

PA26/MIIRXER/ATM8-RxClavII

PA27/MIIRXDV/ATM8-RxSOCII

PA28/MIITXEN/ATM8-RxEnb OO

PA29/MIITXER/ATM8-TxSOC OO

PA3/DS3-RXD1/TDMD2-RXCLK(clock19) I I

PA30/MIICRS/ATM8-TxClav II

PA31/MIICOL/ATM8-TxEnbOI

PB4/MIITXD3/DS3-RXSYNC/TDMA2-L1RSYNC I O I

PB5/MIITXD2/DS3-TXSYNC//TDMA2-L1TSYNC I O I

PB6/MIITXD1/DS3-RXD0/TDMA2-L1RXD0 IOI

PB7/MIITXD0/DS3-TXD0/TDMA2-L1TXD0 OOO

PB8/MIIRXD0/TDMD1-L1RSYNC II

PB9/MIIRXD1/DS3-TXD2/TDMD1-L1TSYNC IIO

PB10/MIIRXD2/TDMD1-L1RXD II

PB11/MIIRXD3/TDMD1-L1TXD OI

PB12/MIICRS/TDMC1-L1RSYNC II

PB13/MIICOL/DS3-TXD1/TDMC1-L1TSYNC IIO

PB14/MIITXEN/TDMC1-L1RXD IO

PB15/MIITXER/TDMC1-L1TXD OO

PB16/MIIRXER I

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC8260TCOM User’s Manual PRELIMINARY

SOFTWARE AND HARDWARE PREPARATION

PB17/MIIRXDV I

PB18/DS3-RXD2/MIIRXD3 II

PB19/DS3-RXD3/MIIRXD2 II

PB20/DS3-TXD1/TDMD2-L1RSYNC/MIIRXD1 IIO

PB21/DS3-TXD2/TDMD2-L1TSYNC/MIIRXD0 IIO

PB22/DS3-RXD1/TDMD2-L1RXD/MIITXD0 IOI

PB23/DS3-RXD2/TDMD2-L1TXD/MIITXD1 OOI

PB24/DS3-RXD3/TDMC2-L1RSYNC/MIITXD2 IOI

PB25/DS3-TXD3/TDMC2-L1TSYNC/MIITXD3 IOO

PB26/TDMC2-L1RXD/MIICRS II

PB27/TDMC2-L1TXD/MIICOL OI

PB28/TDMB2-L1TSYNC/MIIRXER II

PB29/TDMB2-L1RSYNC/MIITXEN IO

PB30/TDMB2-L1RXD/ATM8-MIIRXDV II

PB31/TDMB2-L1TXD/MIITXER OO

PC9/MIIMDIO XXX

PC10/MIIMDC XXX

PC11/DS3-TXD3 O

PC16/MIITXCLK(clock16)/TDMB2-TXCLK II

PC17/MIIRXCLK(clock15)/TDMB2-RXCLK II

PC18/TDMA2-TXCLK(clock14)/MIITXCLK II

PC19TDMA2-/RXCLK(clock13)/MIIRXCLK II

PC20/MIITXCLK(clock12)/ATM8-TxClk II

PC21/MIIRXCLK(clock11)/ATM8-RxClk II

PC22/TDMB1-TXCLK(clock10) I

PC23/TDMB1-RXCLK(clock9) I

PC24/TDMD1-TXCLK(clock8) I

PC25/TDMD1-RXCLK(clock7) I

PC26/DS3-TXCLK(clock6)/TDMC1-L1TXCLK(clock6) I I

PC27/DS3-RXCLK(clock5)/TDMC1-L1RXCLK(clock5) II

PC28/TDMC2-TXCLK(clock4) I

PC29/TDMC2-RXCLK(clock3) I

PC30//TDMA1-TXCLK(clock2) I

PC31/DS3-RXCLK(clock1)/TDMA1-RXCLK(clock1) I I

PD10/TDMB1-L1RSYNC I

PD11/TDMB1-L1TSYNC I

PD12/TDMB1-L1RXD I

PD13/TDMB1-L1TXD O

Table 2: Ports Function Signals

Ports/name T1

ADS

ATM8

FCC1

ADS

FE 0

FCC2

FCC3

TDM1

DS3

FCC2

TDM2

DS3

FCC3

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

PRELIMINARY MPC8260TCOM User’s Manual

SOFTWARE AND HARDWARE PREPARATION

2•1•1 Module Selection.

2•1•1•1 Fast Ethernet selection

As mentioned above, the FE is enabled/disabled by S/W using PC9, PC10 as MII: MDIO and MDC pins.

The FE control is done via the MII internal registers.

FE_1 address = 00001h

FE_2 address = 00010h.

FE_0 address = 00000h (ADS).

2•1•1•2 8 x T1/E1

Each one of the 8 x T1/E1 is enabled by the following ports:

PD4 - T1_1

PD5 - T1_2

PD6 - T1_3

PD7 - T1_4

PD8 - T1_5

PD9 - T1_6

PD18 - T1_7

PD19 - T1_8

2•1•1•3 2 x DS3

Each one of the 2 x DS3 is enabled/disabled by the following ports:

PD25 - DS3 _1 (DS3_1 is enabled only if T1_1 & T1_7 & T1_8 is disabled and PD25 is low).

PA4 - DS3 _2 (DS3_2 is enabled only if T1_3 & T1_4 &T1_5 & T1_8 is disabled and PA4 is low).

2•2 INDICATORS

The MPC8260TCOM has the following indicators.

2•2•1 Fast Ethernet 1 TXD. LD1

LD1 is light whenever the MPC8260 transmits data to FE_1 (LXT970 - U1).

2•2•2 Fast Ethernet 1 RXD. LD2

LD2 is light whenever the MPC8260 receives data from FE_1 (LXT970 - U1).

2•2•3 Fast Ethernet 2 TXD. LD3

LD3 is light whenever the MPC8260 transmits data to FE_2 (LXT970 - U2).

2•2•4 Fast Ethernet 2 RXD. LD4

LD4 is light whenever the MPC8260 receives data from FE_2 (LXT970 - U2).

2•2•5 Fast Ethernet 1 SPEED. LD5

LD5 is light whenever FE_1 (LXT970 - U1) is configured to Fast Ethernet.

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC8260TCOM User’s Manual PRELIMINARY

SOFTWARE AND HARDWARE PREPARATION

2•2•6 Fast Ethernet 1 LINK/LOCK. LD6

LD6 indicates in 100Mbps a scrambler lock and receipt of valid idle code.

LD6 indicates in 10Mbps a Link Valid status.

2•2•7 Fast Ethernet 1 Collision. LD7

LD7 indicates in default mode a collision.

LXT970 can be programmed for other indications. For detailed description see the LXT970 user’s manual.

2•2•8 Fast Ethernet 2 SPEED. LD8

LD8 is light whenever the FE_2 (LXT970 - U1) is configured to Fast Ethernet.

2•2•9 Fast Ethernet 2 LINK/LOCK. LD9

LD9 indicates in 100Mbps a scrambler lock and receipt of valid idle code. (LXT970 - U2)

LD9 indicates in 10Mbps a Link Valid status.

2•2•10 Fast Ethernet 2 Collision. LD10

LD10 indicates in default mode a collision.

LXT970 can be programmed for other indications.

2•2•11 DS3 2 FRAME ERROR. LD11

LD11 is light whenever an error on the F-bit or M-bit is occurred.

2•2•12 DS3 2 RXLOS. LD12

LD12 is light whenever 175 ±75 consecutive zeros appear in incoming data stream.

2•2•13 DS3 2 ENABLE. LD13

LD13 is light whenever DS3 2 is enabled.

2•2•14 DS3 1 FRAME ERROR. LD14

LD14 is light whenever an error on the F-bit or M-bit is occurred.

2•2•15 DS3 1 RXLOS LD15

LD15 is light whenever 175 ±75 consecutive zeros appear in incoming data stream.

2•2•16 DS3 1 ENABLE. LD16

LD16 is light whenever DS3 2 is enabled.

2•2•17 T1/E1 8 ENABLE. LD17

LD17 is light whenever T1/E1 _8 is enabled.

2•2•18 T1/E1 7 ENABLE. LD18

LD18 is light whenever T1/E1_7 is enabled.

2•2•19 T1/E1 6 ENABLE. LD19

LD19 is light whenever T1/E1_6 is enabled.

2•2•20 T1/E1 5 ENABLE. LD20

LD20 is light whenever T1/E1_5 is enabled.

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

Tabla de contenidos

Otros manuales de Placa madre de Freescale Semiconductor

Freescale Semiconductor

Freescale Semiconductor Freedom FRDM-KE15Z Manual de usuario

Freescale Semiconductor

Freescale Semiconductor NXP DEMO9S08JS16 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor Freedom FRDM-KW24D512 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor CSM-56F801 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33814AEEVBE Manual de usuario

Freescale Semiconductor

Freescale Semiconductor M5407C3 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor 56F8300 Series Manual de usuario

Freescale Semiconductor

Freescale Semiconductor DEMO908QB8 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MC13851 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor LS1043ARDB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor NXP 56F8013 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KIT33926PNBEVBE Manual de usuario

Freescale Semiconductor

Freescale Semiconductor Qorivva MPC5746R-176DS Manual de usuario

Freescale Semiconductor

Freescale Semiconductor TWR-MPC5125 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor TWR-K70F120M Manual de usuario

Freescale Semiconductor

Freescale Semiconductor BSC9131RDB Manual de usuario

Freescale Semiconductor

Freescale Semiconductor K20D72M Manual de usuario

Freescale Semiconductor

Freescale Semiconductor IB112 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor MPC8313E PowerQUICC II Pro Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KITVR500EVM Manual de usuario

Freescale Semiconductor

Freescale Semiconductor eXtreme Switch Gen4 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor KL25Z128VLK Manual de usuario

Freescale Semiconductor

Freescale Semiconductor PowerQUICC MPC885 Manual de usuario

Freescale Semiconductor

Freescale Semiconductor Freedom FRDM-KE04Z Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario