Franklin U210 Manual de usuario
1. BEFORE USING U210
A
bout This User’s Manual
This user manual contains all the necessary information regarding the device
installation and how to use the modem for your internet navigation. Please make sure
that you are familiar with the device operation by carefully reading this user manual
before using the U210 EVDO USB modem..
Instructions
• Install the Franklin Access Manager™ software by inserting the U210 USB Device into
your PC. The installation software is included in the U210 modem memory. When you
insert the U210 into your computer, the installation process will automatically begin.
• It is highly recommended that you read the safety precautions described in this
manual before using the U210.
Documents Included on your Modem Memory
• Broadband Usage Conditions, Terms & Conditions
User Manual
Product Overview
Welcome and thank you for choosing U210 USB Modem for your wireless internet
connection.
The U210 is a high-speed wireless device that enables your computer to connect to 3G
high-speed wireless network. The U210 provides simple yet powerful user interface
that is easy to install and use.
Product Package Contents
The following items are included in the product package. If any of the items listed
below are missing, please contact the local retail store where you purchased the
product.
• U210 Modem Device
• Quick Start Guide
• USB Extension Cable
• Carrying Pouch
Introduction to U210 USB Modem
The U210 is designed for the USB port on your computer, which is available in most PC
models. The U210 allows you to
• Access the Internet,
• Send and receive e-mail
• Access your corporate network through VPN
With U210, you are always connected whether you are away from home, on the road,
or wherever wired Internet access is not readily available.
Product Specifications
• Power management: The U210 utilizes power management and system overhead
reduction functions provided by the USB interface for maximum power savings.
• Antenna design: Its efficient and innovative design optimizes data transfer rate and
sensitivity to network signals.
• Extension USB cable connector: This extension cable may be used to increase RF
performance, and to resolve clearance issues if there is any.
• USB Modem that supports Type A USB Port interface.
• Supports PCS(1900 MHz) and Cellular (800 MHz) dual bands.
• Utilizes Qualcomm QSC6085 chipset
• Supports high-speed network technologies
• Support Windows XP, Vista, 7 and Apple Macintosh systems with installed Franklin
A
ccess Manager™ connection manager software and driver.
Product handling
• Do not place any adhesive labels on the USB connector. It may leave a sticky residue
that can cause problems inside the PC USB port.
• The U210 USB device should easily slide into the USB port. Do not force the U210
into the USB port as it may cause damage to the modem and/or the port.
• Keep the U210 in a dry and clean place. (Storage temperature: -22°F to 149°F [-
30°C to 65°C]). Keep your device away from liquids, dust and excessive heat.
Configuration
To use the U210 on your computer, you need to install the Franklin Access Manager™
software included in the modem memory and configure the U210 USB device. See the
next section for more information on software installation and USB device configuration.
The following section will guide you through the installation and setup process for
Franklin Access Manager™ software. Before getting started, you should become
familiar with the documentation that came with your USB Modem.
2. INSTALLATION AND SETUP FOR FRANKLIN
A
CCESS MANAGER™
This section will guide you through the installation and setup process for Franklin
A
ccess Manager™ software.
Before getting started, you should become familiar with the documentation that came
with your USB Modem.
Installing Software
Warnings
• Make sure to complete the unplugging/ejection process before removing the U210.
• If you remove the device improperly, the modem may be damaged.
Notes
• If you have inserted the device properly, Windows will inform you of the new
hardware. Wait until Windows completes the “Found New Hardware” task.
• In Windows 2000, several windows similar to “Found New Hardware” window can
appear and disappear automatically. In Windows XP, several tool tips similar to the
“
Found New Hardware” function will appear and disappear in the system tray
automatically. In Windows Vista, several tool tips similar to the “Installing device driver
software” function will appear and disappear in the system tray automatically. Once
hardware detection is complete, you will be prompted to start activation.
• It is normal to hear a short beep sound each time you insert or remove the U210.
• It is an audible notification that your PC recognizes the new hardware.
Getting Started (Windows)
To install the Franklin Access Manager™ software:
Turn on your computer then close all applications.
Insert the U210 modem into your USB port.
Your computer will recognize U210 modem and start the installation sequence
automatically. If the program does not launch automatically, go to my computer and
select the ‘FAMCD’ drive and double click ‘start.exe’ program.
Follow the steps in the next section.
Setup Program – for Windows
STEP 1
: The “Welcome to the Franklin Access Manager Setup Wizard” screen
appears. Click the [Next] button to continue with the installation process.
STEP 2
: You are now ready to select the location on your computer where Franklin
A
ccess Manager™ will be installed. It is recommended that you do not modify the
default destination folder. Click the [Next] button to continue.
STEP 3
: During this step the components of Franklin Access Manager product are
being installed onto your computer. Installation will occur to the destination folder
specified in Step 2.
STEP 4
: Installation of Franklin Access Manager is now complete. Click the [Close]
button to leave the Franklin Access Manager setup program and begin using your new
software.
• The setup program will automatically create a Franklin Access Manager shortcut on
your desktop.
STEP 5
: Please wait while U210 is installed and ready to use.
3. STARTING FRANKLIN ACCESS MANAGER™
Franklin Access Manager™ is a connection manager application for U210 USB modem.
It allows you to manage and monitor the Internet connection between your computer
and the wireless network. It has user friendly interface and is equipped with many
useful features that will enhance your internet navigation experience.
Features
WWAN(Wireless Wide Area Network, 1xEV-DO/1xRTT/CDMA)
Specific Features:
• Configures your computer to use your USB Modem
• Creates a Data Connection for your USB Modem
• Copies utility to create wireless copies of your dial-up connections, if supported by
your device
• Test function for WWAN device
A WWAN capable device is required to use the WWAN features. Individual WWAN
features are also device dependent as described in the WWAN section above.
Other Features:
• Logs connections used, duration of the usage, and bytes sent and received.
• See the section “Additional Features” for more information about the features of
Franklin Access Manager™ software.
Getting Started
Double click on the Franklin Access Manager icon on your desktop or click on the
Windows Start menu and select Franklin Access Manager from the list of programs.
A
bout the Wireless Networks View
Franklin Access Manager will open the Broadband Networks window as shown below.
This view is where you manage your Broadband connections. The Broadband Networks
window displays all the available network connections.
A
t a glance you can see the signal strength. Your current connection state and the
elapsed time of the connection are displayed along the bottom of the status bar.
Connecting to the Internet
Once your device is properly configured, connecting to the Internet is as simple as
clicking the “Connect” button.
Once connected, the “Connect” button will change to “Disconnect”.
Simply click this “Disconnect” button to end your current connection. To connect to any
other network shown, select it, and then click the “Connect” button.
The Status Bar
Information regarding your current network connection can be seen in the status bar
along the bottom of Franklin Access Manager interface. For more information on this
status bar, see the section “The Status Bar” in the “Additional Features” section.
Franklin Access Manager will display status information at the bottom during the
connection process as well as while connected.
When it is not connected, the status text in the lower left corner will display “Not
connected” for the currently selected network. The timer will display “00:00:00”. Once
connected, the status text will display “Connected” and the timer will begin to run.
Right clicking on the tray icon provides various options and double clicking on it will
always show the application. Placing your mouse pointer on it will display the current
connection status.
Based on your preferences, your browser can be launched automatically upon
connection.
Using the “Data” connection:
By default Franklin Access Manager enables the software for data connections.
If your connection fails when you try to connect, please try to reconnect.
Dormancy:
The data session can go to dormant mode if you are not sending or receiving any data
for an extended period of time. As soon as you resume sending or receiving data, the
data session will return to an active state automatically.
4. USING FRANKLIN ACCESS MANAGER™
The Session Menu
•
Connect / Disconnect
: Use this button to connect or disconnect the wireless
networks.
•
Statistics
: At any time during your connection you can check your current
connection speed and throughput stats in the Statistics window. To see this window,
select “Statistics” from the “Session” menu.
•
Exit
: Close the Franklin Access Manager™ Software
The Tools Menu
•
Log
: This feature provides a concise session log of your network activity. Click on a
column heading to sort the log. This window also displays the total number of sessions
as well as the total connected time. The information displayed in the Usage log can be
customized using the controls that appear just below the list.
• To view only the connection history of a specific network type, check the “Selected
connection” checkbox and select the desired type from the drop-down list.
• To view only the connections made during a specific interval, check the “Date range”
checkbox and specify the date in the “From:” and “To:” fields.
• To clear the log, press the Clear button. Note that clearing the log cannot be undone.
•
Activation
: Programs the activation code, phone number, and IMSI(MIN) to the
USB Modem.
•
Test Device
: Retrieve and display detailed information about your WWAN device
(1xEV-DO/1xRTT/CDMA USB Modem) such as CM port, model, MEID, MDN, etc. This
information can be valuable when troubleshooting a problem.
Tabla de contenidos
Otros manuales de Módem de Franklin
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario