Frama Matrix F Series Manual de usuario

QUICK IP INSTALLATION GUIDE

FOR MATRIX F SERIES

Note!

Please always refer to the full manual (Matrix F series IP Configuration Manual) available

on frama.com/support or from your local distributor.

TCP/IP Specification of Frama Matrix F series TCP/IP port

Connection / Protocols

TLS v1.2 embedded

FIPS 140-2 certified SSL stack

Ethernet 10 Base-T (IEEE 802.3i)

Half duplex

RJ45 socket

Internet protocol IPv4

Complete and reliable TCP/IP Linux stack

Supports DHCP (standard) and Static IP Address Configuration

Note!

The Ethernet port used on Frama Matrix F series is only active and enabled during

connection with FramaOnline2!

System Requirements / Preparation

In order to connect your Franking System with the FramaOnline2 system, you minimally require the following:

Firewall

Port 443 open

Port 53 open if the DNS is located outside the network the Franking System is connected to

Infrastructure:

An Ethernet network socket that connects to the Internet

The Franking System must be able to access DNS via TCP port 53

The Franking System must be able to communicate via TCP port 443 (https / SSL) to the URL fo2.frama.com

Proxy server

The Franking System supports connection via an http proxy server with basic authentication or without

authentication.

Note!

Communication via Proxy Server with SSL Interception is not supported!

Due to security requirements, the Franking System cannot connect through a https proxy server

that intercepts the SSL encrypted communication.

Tip!

Proxy servers using SSL-interception require a specific rule in order to allow transparent

communication (Franking System via F-Link to FramaOnline) via https port 443.

The specific rule grants correct identification of FramaOnline2 (https certificate) for the Franking

System.

Quick-Start Installation and Configuration

If you connect your Franking System to a so-called SOHO (Small Office / Home Office) infrastructure via a DSL

router to the Internet, installation and configuration of the Franking System is very simple and straight forward:

Preconditions:

(DSL) Router device connecting to the Internet.

DHCP enabled on router and access to Internet from LAN not restricted.

Procedure:

Make sure that the Franking System is switched off.

Connect the green framed RJ-45 socket labelled „LANG4“ of the

Franking System with a free LAN-port on your router using a

standard CAT5 RJ-45 network cable.

Power on the Franking System.

Check the connection as described in section 8.8 of the full manual.

Tip!

Perform the required installation connect as described in your Franking System user manual

to trigger the initial connection to the FramaOnline2 system.

Perform any subsequent inspection or re-set connections as described in your Franking

System user manual.

Note!

No user management of the system can be done via web browser. All changes to the system

can only be done directly from the machine itself.

IT Security Information

No DOS based system.

No Windows based system.

No open Ports on the FS LAN module.

The franking system always initiates the connection to the FramaOnline2 backend system; this means all

connections to our servers are established only by the Franking System.

The Franking System is not listening on ports and therefore does not accept any connections from outside.

The system will only need Internet access to connect to fo2.frama.com for loading credit and inspections,

during other periods the LAN module is always off.

The connection between FS LAN module and our server is HTTPS / TSL1.2 / SHA-II encrypted using port

443.

All Franking Systems only accept firmware updates carrying a digital signature from Frama.

TÜV-IT intrusion and Man-in-the Middle attack tests passed.

Note!

Please always refer to the full manual (Matrix F series IP Configuration Manual) available

on frama.com/support or from your local distributor.

Frama AG, Switzerland 10/17, R01.00

Otros manuales para Matrix F Series

Tabla de contenidos

Otros manuales de Equipos postales de Frama

Frama

Frama MATRIX F2 Manual de usuario

Frama

Frama EcoMail Manual de usuario

Frama

Frama Access B300 Manual de usuario

Frama

Frama Matrix F32 Manual de usuario

Frama

Frama Matrix F12 Manual de usuario

Frama

Frama Access B400 Manual de usuario

Frama

Frama Fx 7 Series Manual de usuario

Frama

Frama MATRIX F22 Instrucciones de instalación

Frama

Frama Access B400 Manual de usuario

Frama

Frama Access B400 Manual de usuario

Frama

Frama Fn 5 Series Manual de usuario

Frama

Frama Fx 5 Series Manual de usuario

Frama

Frama Fs 3 Series Manual de usuario

Frama

Frama MATRIX F22 Manual de usuario

Frama

Frama Mailmax Manual de usuario

Frama

Frama Matrix F Series Hoja de instrucciones

Frama

Frama Matrix F32 Manual

Frama

Frama Access B400 Manual de usuario

Frama

Frama Matrix F4 Manual de usuario

Manuales populares de Equipos postales de otras marcas

Radius

Radius LETTERMAN II Manual de usuario

Radius

Radius LETTERMAN III Manual de usuario

Neopost

Neopost IS-350 Manual de usuario

FP optimail Manual de usuario

Florence

Florence Package Protector PORT Manual de usuario

FP centormail Manual de usuario

SSS Siedle

SSS Siedle BG/SR 611 Series Manual de usuario

Labelmate

Labelmate UCATS MINI Manual de usuario

Pitney Bowes

Pitney Bowes SendPro C Manual

OMUARK

OMUARK Uark Manual de usuario

FP Postbase Mini Manual de usuario

Pitney Bowes

Pitney Bowes F731 Manual

XPOtool

XPOtool 60000 Manual de usuario

Hefter Systemform

Hefter Systemform LO 440A Manual de usuario

Pitney Bowes

Pitney Bowes 7H20C Manual de usuario

eSafe

eSafe ENTRADA RANGE Manual de usuario

Salsbury Industries

Salsbury Industries 4325D Manual de usuario

MSL

MSL JET PLUS 500 Manual de usuario