FOVNO ES-H1B Manual de usuario

全电动倒立吸盘车顶架说明书

FOVNO Electric Inverted Sucker Bike Rack Instructions

Please read these instructions carefully before using this product. The instructions contain important information

which will help you get the best out of the product and ensure safe and proper installation, use and maintenance.

· Do not squeeze or impact the product forcibly.

· Do not disassemble or modify this product.

· Children should be supervised to ensure that they do not use this product as a toy to avoid unnecessary accidents.

· This product needs to be used with the attached alarm, which serves as a reminder during the use of the roof rack. If, when in use, the alarm continues to sound please stop your

vehicle and check our troubleshooting guide. If you are unable to solve the issue, please refrain from using the product until you have contacted customer service.

· In normal use of this product, the suction foot will slowly leak air. When the air pressure inside the leaking suction foot reaches the set minimum pressure value, the N-Power

control box will pump the air automatically, and the alarm will sound. The alarm will stop after a few seconds. The time it takes the N-Power control box to create a vacuum

depends on the hose length and other system settings. Normal operating time is between 2 - 15 minutes and during this time it is normal for the alarm to sound.

· It is normal for the suction foot to leak slowly during use. If the control box starts frequently within 2 minutes(while the alarm keeps buzzing), It is considered to be air leaking too

fast. Frequent start of the control box will cause the internal motor to overheat and not function properly. If similar situations occur, please check whether the suction foot is

damaged, whether the suction part is ﬂat and smooth or whether the hose and quick connector are damaged immediately. If the above problems are removed, but the frequent

start-up phenomenon still occurs, it could mean something is a problem with the product. Please contact customer service immediately. Some products have a particularly

good sealing performance and when the adsorption surface is particularly smooth, it may cause the control box to work automatically at an interval of more than 20 minutes.

If the buzzing alarm doesn't go oﬀ for a long time, please open the suction foot, in which way, you will ﬁnd out if the control box is working normally. If the control box is working

normally, there is no need to worry.

· Before use, please check the battery charge level in the N-Power control box and charge if needed. Do not use with a low battery.

· Before use, please check whether the roof rack control box is working normally with suﬃcient power. Press the control box sunction foot on a smooth surface, turn on the

power switch, and press the control box vertically with your hand. After all the suction foots seal to the surface, open any of the suction foots, the control box should start to

work and this suction foot should re-adsorb the surface immediately, this is what we consider normal operation (Meanwhile, connect to the power of the alarm. the alarm should

start to buzz with the control box starts to work, and stop when the suction foot adsorbed completely).

· Before use, make sure that the ﬁlter sponge at the suction port on the bottom of the suction foot is in good condition. The ﬁlter sponge has a great protective eﬀect on the

adsorption of the suction foot. It prevents dust or other items from entering the suction pipe and guarantees the airtightness of the air valve in the suction foot.

Terms and Conditions

· Before use, please clean the roof area and the bottom surface of the suction foot to be installed with water and dry with a microﬁbre cloth. The suction foot can be installed after

ensuring that the area is free of dust and water.

· When using, please install the roof rack on a ﬂat and smooth part on the roof. The surface where the suction foots are placed must not have cracks. Do not install the roof rack in

places where there vinyl stickers or where there are joins between panels, glass or plastic.

· While driving, check whether the control box is working normally every 4 hours using the method above, and check whether all the suction foots are functioning.

· When using this product, please pay attention to the following items: the highway speed should not exceed 120km/h, and the ordinary road should not exceed the speed limit

sign. Be aware of road conditions and drive slowly on uneven or bumpy conditions.

· There is a lithium battery in the control box of this product. The temperature will aﬀect its eﬃciency. It is recommended to use in an environment at a temperature between

-20°C and +40°C.

· During use, if the control box cannot work normally due to force majeure, please do not panic. Each suction foot of this product is equipped with an air check valve. Even if the

control box is not working normally, the suction foot can still be ﬁrmly adsorbed for at least 1 hour. Please get oﬀ the car in a safe place to check and troubleshoot the problem.

If the control box still does not work normally, please stop using it immediately and contact our company's customer service for repair as soon as possible.

· When the roof rack is not in use, please dust seal plug the air pipe quick interface on the control box and the main suction foot with a rubber plug to prevent foreign objects from

entering and aﬀecting the normal operation of the roof rack.

FOVNO Electric Inverted Sucker Bike Rack

Introduction

Learn about your new FOVNO bike rack

Pneumatic hose

N-Power control box

Suction foot

Handlebar clamp

Handlebar strap

Saddle holder

Saddle strap

Suction foot

Dust seal plug

(Dust seal: When the rack is not in use

please use the dust seal to protect the

pneumatic connections.)

N-Power Control Box

Alarm

Pairing

Alarm System Instructions

1. Your bike rack is ﬁtted with a safety alarm which will alert you if the back loses its connection with the vehicle. The alarm

will sound if a suction foot leaks. In the even of this happening the N-Power system will automatically attempt to create a

vacuum seal using the built in pump.

2. The alarm module is ﬁtted with a standard USB which can be connected to your vehicle either via the vehicles own USB, a

USB adaptor or USB port on a sound system. The alarm will connect to the N-Power box wirelessly and will alert you in the

even of a pressure error. Double sided toe on the underside of the alarm can be used to hold it in place.

3. PLEASE NOTE: If you are using more than one FOVNO bike rack system on your vehicle the alarm system may not operate

correctly due to a shared signal. While the alarm may not operate the N-Power box will still function as normal.

Pairing method of alarm and control box

1. Clear data: There is a small hole on the back of the

alarm that is a button for the pairing switch. After the

alarm is connected to the power supply, press the switch

button in the small hole for about 10 seconds.When the

indicator light of the alarm is oﬀ, it meansthat the original

data is cleared.

2. Use the same method to press the switch button in

the small hole of the alarm for about 3-5 seconds. After

the alarm indicator lights up, start the control box, and

then stop pressing the pairing switch. At this time, the

alarm buzzes, the pairing is complete.

Introduction

N-Power Control Box Functions

· Charging: Charging the N-Power box is easy and thanks to the USB-C connector you can charge from a phone charger

power band or a USB charger. Simply remove the waterproof / dust cover and charge with the included USB C wire.

· The N-Power control box features USB lights that tell you the level of charge in the battery. An orange light indicates the

system needs charging, blue means full and a red light indicate the system is being charged. To check the battery level press

the button on the N-Power control box.

Note: The charging voltage is 4V-6V, if it exceeds this range, it will aﬀect the charging or damage the charging module.

Quick release air hose connection

USB Type-C connector Power button

Battery health check button

(Red light when charging

blue light when fully charged）

（Blue light-normal, red and orange

light-charging instantly）

red orange blue blue blue

The underside of the alarm

A button for the pairing switch

Replace the dust seal plug

when not in use

b. While pressing the leve

carefully pull the hose loose

a. Press the lever to release

the locking interface

① ②

②

Installation of your FOVNO bike rack

Introduction

Suction ﬁlter

Base of foot Gasket

Warning: Ensure the suction foot ﬁlter is clean

and in good condition.

Press in hose

Remove the dust seal plug

(please keep it in a safe place)

Hose Connection

Hose Disconnection

①

CPC Dust Seal Plug×2

FOVNO Electric

Inverted Sucker

Bike Rack

Model Number

Package Size Size

System Weight

Carry Capacity

Protection Grade

Our products have acquired the CE-RED,FCC-RED,ROHS,UKCA,UN38.3,MSDS,EN62133 Certiﬁcation.

IP65

1 bike

Battery Capacity 3400mAh

Input

Power 13W

Maximum Negative Pressure -65KP

Wireless Transmission Frequency 433.92MHZ

What's in the box

Introduction

Name

N-Power Control Box

Handelbar Suction Foot Saddle Suction Foot Accessories Spares

250×40mm Crank Strap×1

Alarm×1

USB Type-C Cable×1

Microﬁbre Cleaning Cloth×1

Seals×4

Suction Foot Filters×4

Gaskets×4

Speciﬁcation

ES-H1B

350×320×145mm

3.3kg

DC5V

×2 ×1

Handlebar installation and removal

Install handlebar Remove the handlebar

Instructions

Lock the handlebar

Shake

Tighten the handlebar

Penetrate

Release handlebar

Press button

Remove handlebar

Pull apart

1. Place the alarm in the vehicle connect the alarm to a suitable USB power supply. If working normally a red LED light will be shown.

2. Install the handlebar suction foot and saddle suction foot on the bicycle as shown in FigureⅠ, and tie the straps tightly, with the bottom surface of all suction foots facing upwards

horizontally. Connect the hose on one of the handlebar suction foot to the other handlebar suction foot.

3. Invert the bicycle to the roof of vehicle, adjust the bicycle to be parallel to the vehicle body, adjust the position of the handlebar suction foot and the saddle suction foot , so that the

bottom surface of the suction foot fully ﬁts the installation surface.

4. As shown in FigureⅡ, select a suitable position to absorb the control box (the direction of the hose interface of the control box suction foot is towards the rear of the vehicle), and

connect the hoses of the handlebar suction foot and the saddle suction foot to the control box, so that the suction foots are completely adsorbed on the installation surface superior.

5. Before driving,check the handlebar suction foots and saddle suction foot are tight with bike and vehicle.

Instructions

Installation method 1

FigureⅠ FigureⅡ

Installation method 2

1. Place the alarm in the vehicle Connect the alarm to a suitable USB power supply,If working normally a red LED light will be shown.

2. Select the installation position of each suction foot on the roof or back of the vehicle according to Figure Ⅲ

3. Put the control box suction foot in the selected position, turn on the power switch,and press the control box down,so that the suction foot is fully adsorbed on the installation

surface.

4. Open the handlebar clamps of handlebar suction foots according to Figure Ⅳ, and place them in the selected position.The distance between the two is determined according to

the length of the two sides of the bicycle handlebar. Connect the pneumatic hose as shown in Figure Ⅳ, and press the handlebar suction foots respectively,then the two handlebar

suction foots will be automatically attached to the installation surface.

Instructions

Figure Ⅲ

Figure Ⅳ

Tabla de contenidos

Otros manuales de Accesorios para bicicletas de FOVNO