Fortress Security Store S02 Manual de usuario

S02 ALARM SYSTEM

•

INTRODUCTION

QUICK START

SYSTEM BASICS

ADVANCED SETUP

.............................

.................................

.............................

.........................

What’s In The Box?

First-Time Setup and Testing

Installation

Zone Chart

Telephone Setup

Entry Delay Setup

Arming / Disarming

Changing Your Password

Adding / Removing Accessories

Syncing Sirens

Zone Settings

Other System Settings

Entry Delay Time

Exit Delay Time

Siren Chirp

Door Chime

Phone Line Cut Reminder

Ring Count

Siren Alert Time

Controlling Your System Remotely

Support For Wired Sensors

Panel Behavior

Technical Specications

Space For Notes

TABLE OF CONTENTS

INTRODUCTION

Welcome to your new S02 alarm system from Fortress Security

Store. This easy-to-use, self-install burglar alarm system works

with one or more loud sirens to alert anyone nearby of a pos-

sible break-in. Using your existing phone line, the system can

also call you and alert you when you’re away from home.

THE BASICS

ADVANCED

In this User Manual, you will nd the following sections:

Learn the basic day-to-day features of your system

Dive into the details of customizing your system

WHERE TO FIND USEFUL INFORMATION

AND VIDEOS

A great collection of FAQ articles and videos for getting started

are available online. Visit our website and click on the Support

tab.

QUICK START

Quickly get up and going with your rst time setup

HOW DOES THE S02 ALARM SYSTEM

WORK?

When the alarm is triggered, any sirens will start making noise

to scare off intruders and alert you. Additionally, if connected

to a phone line, it will call the phone number(s) you program

and play a brief recorded message (which you record). A Zone

Number will also appear on the screen to indicate which sen-

sor triggered the alarm. The system can be armed in Home

mode to protect the perimeter of the house while allowing you

to move around freely inside. Some accessories such as smoke

alarms will trigger the alarm even if the system is disarmed.

https://www.FortressSecurityStore.com

If you’re anything like us and don’t want to have to read an

entire manual to set up your system, this quick start guide is

the perfect solution.

Here’s a breakdown of the Quick Start guide:

QUICK START

•All S02 systems come with at least the items above.

We offer multiple sizes of the S02 kit. Look for the size you

purchased on the table on the next page to see what sensors

you have and what zones they are programmed to.

•If you purchased a custom-built kit, this chart may not re-

ect how your system is congured.

WHAT’S IN YOUR BOX?

•What’s In Your Box

•First Time Testing

•Installation

•Zone Chart

FIRST TIME TESTING

To turn on your panel for the  rst time, plug in the included

power cable to the wall and into your panel, then turn the

power switch ON.

Some sensors will have a battery tab or a plastic protective

covering over them. Before you get started testing, follow

these steps:

GETTING YOUR SENSORS READY

•Remove battery saver tabs

•Turn on any sensors with a power switch

•Plug in sensors that require power

ON / OFF

To test your sensors, follow the steps below:

• Arm your system *

• Trigger a sensor **

• Make sure that you see the sensors zone number appear on

the screen (this means the alarm was triggered)

• Disarm the system.

• Repeat the steps above until all sensors have been tested.

* If you have questions on how to arm/disarm the system,

refer to page 10.

** If you are unsure how to trigger one of your sensors, refer

to page 14.

Note: When testing your motion detectors, be sure to arm the

system in Out mode. They will not trigger the alarm in Home

mode.

TESTING YOUR SENSORS

We recommend you test all your sensors/sirens before you

install your system. This will help you ensure that everything

is working as it should.

TESTING YOUR SIRENS

Plug in all sirens and turn on the power switches if applicable,

then trigger your alarm. It does not matter which sensor you

trigger; it is only important that the alarm goes off.

Be sure all sirens are sounding, then disarm your system.

To arm, press and hold ‘Out’ or ‘Home’ until the panel beeps.

To disarm, type in 1234, then press the Disarm button.

INSTALLATION DO’S AND DON’TS

This table addresses some common questions you may have

during the setup process. Set it up right the  rst time, and save

on painkillers from the headache you avoided!

Note: Do not mount any transmitters directly on metal. This

will ensure that the transmissions from the sensors make it to

the main panel successfully and reliably.

More detail about programming the system can be found in

our advanced setup instructions on page 14. Alternatively, visit

our website and click on the Support Tab.

https://www.FortressSecurityStore.com/

ZONE CHART

Before installing your sensors, we recommend you write

down their intended location. This will help you remember

which sensor is in what area.

Each sensor has a number. That number is the zone it is assigned to

Note: If you need more space, there is room at the back of the manual.

01 02

03 04

05 06

07 08

09 10

11 12

13 14

15 16

17 18

19 20

21 22

SYSTEM BASICS

This section will teach you how to set up the basics of your se-

curity system, above and beyond the information in the Quick

Start section.

Here’s a breakdown of the System Basics section:

•Telephone Setup

•Entry Delay Setup

•Arming/Disarming [In Depth]

•Setting A New Password

TELEPHONE SETUP

In order for you system to complete calls, you will need to plug

it into a landline. Completing both steps below is not neces-

sary; you will only need to plug your phone base station into

the S02 if you have only one landline wall jack.

Follow these steps to set it up:

•Plug the phone cable from your wall jack into the Out Line

Port on the S02 panel.

•If using on a shared phone line, plug a cable from your tele-

phone port to your phone base station

Note: We recommend using a dedicated phone line for your

alarm system. Sharing a line with anything else can cause dis-

ruptions or keep the security system from being able to make

or receive calls.

PROGRAMMING PHONE NUMBERS

The S02 system has a self-monitoring feature, which means

that the system can optionally call up to 6 different phone

numbers and play a brief recorded message. An existing phone

line with a working dial tone is required for this feature.

To program a phone number into slot 31, follow the below

steps:

There are 6 available slots where you can program up to 6

phone numbers. These slots are numbered 31 through 36. The

example above shows how to program a number into slot 31,

but you can use any number between 31 and 36. The system

will call the numbers in the order they are stored.

Note: You can use up to a 14-digit phone number.

RECORD A MESSAGE

When your system calls you, it will play a recorded message.

If you do not record anything on your panel, the line will be

silent when you answer the panel’s outgoing call.

To record a message, follow the steps on the next page.

Tabla de contenidos

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario