Fortinet Wireless Starter Kit Manual de usuario

Wireless Starter Kit Guide

for FortiOS 4.0 MR2

Wireless Starter Kit Guide

23 February 2011

01-420-139115-20110223

for FortiOS 4.0 MR2

diagrams or illustrations may be reproduced, transmitted, or translated in any form or by any means,

electronic, mechanical, manual, optical or otherwise, for any purpose, without prior written permission of

Fortinet, Inc.

Trademarks

Dynamic Threat Prevention System (DTPS), APSecure, FortiASIC, FortiBIOS, FortiBridge, FortiClient,

FortiGate®, FortiGate Unified Threat Management System, FortiGuard®, FortiGuard-Antispam,

FortiGuard-Antivirus, FortiGuard-Intrusion, FortiGuard-Web, FortiLog, FortiAnalyzer, FortiManager,

Fortinet®, FortiOS, FortiPartner, FortiProtect, FortiReporter, FortiResponse, FortiShield, FortiVoIP, and

FortiWiFi are trademarks of Fortinet, Inc. in the United States and/or other countries. The names of actual

companies and products mentioned herein may be the trademarks of their respective owners.

Wireless Starter Kit Guide

01-420-139115-20110223 3

http://docs.fortinet.com/ • Feedback

Contents

FortiAP™ Wireless Starter Kit 5

FortiAP unit overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Power options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

FortiGate wireless controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting the hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Checking the firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Obtaining and installing the FortiGate firmware . . . . . . . . . . . . . . . . . . . 9

Obtaining and installing the FortiAP firmware . . . . . . . . . . . . . . . . . . . 10

Installing the Starter Kit configuration . . . . . . . . . . . . . . . . . . . . . . . . . 10

Obtaining the configuration file . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Demonstrating authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Discovering and enabling the FortiAP units . . . . . . . . . . . . . . . . . . . . 11

Confirming that the wireless access points are activated . . . . . . . . . . . . . 12

Viewing the profile-based configuration . . . . . . . . . . . . . . . . . . . . . . 12

Checking wireless signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Captive portal demonstration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

WPA shared key demonstration . . . . . . . . . . . . . . . . . . . . . . . . . . 14

WPA/WPA2-Enterprise demonstration . . . . . . . . . . . . . . . . . . . . . . . 14

WPA Client Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

WPA/WPA2-Enterprise with external database demonstration . . . . . . . . 14

WPA/WPA2-Enterprise with local database demonstration . . . . . . . . . . 14

Monitoring traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Rogue AP scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Contents

Wireless Starter Kit Guide for FortiOS 4.0 MR2

401-420-139115-20110223

http://docs.fortinet.com/ • Feedback

Wireless Starter Kit Guide

01-420-139115-20110223 5

http://docs.fortinet.com/ • Feedback

FortiAP™ Wireless Starter Kit

The purpose of the Wireless Starter Kit is to provide a very cost effective and simplified

way to showcase the capability of FortiAP wireless access points. This document

introduces the FortiAP unit and the FortiOS wireless controller feature as demonstrated in

the Starter Kit.

FortiOS is the operating system of FortiGate and FortiWiFi units.

FortiAP unit overview

A FortiAP unit, of which there are several models, is a compact wireless access point

device. Indoor units can be wall-mounted or ceiling mounted. An optional ceiling tile rail

mount is available. It is also acceptable to place the unit on a desktop or shelf. There is

also an outdoor model available.

The FortiAP unit contains the radio equipment required for a wireless access point. It must

be controlled by a FortiGate or FortiWiFi unit.

Features

• Most models have dual radios for simultaneous 802.11a/n & 802.11 b/g/n operation.

FortiAP-210B is a single-radio model.

• Four high-gain dual band (2.4GHz, 5GHz) omni-directional antennas. Single radio

models have two antennas. Indoor models have internal antennas.

• 2x2 MIMO configuration using the latest signal processing technology. 600Mbps total

throughput for dual-radio units, 300Mbps for single-radio units.

• 14 SSIDs for client access, (7 for single radio models)

• 2 SSIDs for dedicated monitoring, (1 for single radio models)

• Firmware upgradable through the wireless controller.

FortiAP unit overview FortiAP™ Wireless Starter Kit

Wireless Starter Kit Guide for FortiOS 4.0 MR2

601-420-139115-20110223

http://docs.fortinet.com/ • Feedback

Rear panel

All connections to the FortiAP unit are made on the real panel.

In typical use as a wireless access point, only Port 0 is used. An Ethernet cable connects

Port 0 to a port on the FortiGate unit. The Power jack is connected to the power supply

provided with the FortiAP unit. Optionally, you can use a power-over-Ethernet (POE)

adaptor to avoid the need for a power outlet near the FortiAP unit. In that case, the power

output of the POE adaptor connects to the Power jack.

Front panel

The front panel contains indicators that show the status of the unit.

Port 1, 2, 3, 4 Green indicates a connection to the corresponding port on the rear panel.

Wireless Flashing indicates wireless network running.

Port 0 Green indicates a network connection to Port 0 on the rear panel.

Port 0 connects to the FortiGate unit that acts as the wireless controller.

Power Flashing - power connected but unit not managed.

Lit steadily - indicates that the unit has power and is managed.

FortiAP™ Wireless Starter Kit FortiAP unit overview

Wireless Starter Kit Guide

01-420-139115-20110223 7

http://docs.fortinet.com/ • Feedback

Power options

The FortiAP unit requires 12 volts and power supply with universal 100-240 volt input is

provided. If power is not conveniently available at the mounting location, it is possible to

use a power-over-Ethernet (POE) adaptor to feed 12 volt power to the device through the

Ethernet cable. POE adaptors have two components: one to combine power and Ethernet

and the other to separate them again. The wiring looks like this:

FortiAP units have been tested with the LinkSys WAPPOE12 adaptor. Use the power

supply provided with the FortiAP, rather than the power supply provided with the POE unit.

FortiOS wireless controller FortiAP™ Wireless Starter Kit

Wireless Starter Kit Guide for FortiOS 4.0 MR2

801-420-139115-20110223

http://docs.fortinet.com/ • Feedback

FortiOS wireless controller

The FortiOS wireless controller feature enables FortiGate and FortiWiFi units to manage

FortiAP units. The wireless controller configuration is composed of three types of objects:

Virtual AP — defines the security settings for your wireless network. This is similar to the

wlan interface settings on a FortiWiFi unit and it creates a virtual network interface.

AP Profile — defines the radio settings, such as band (802.11g for example) and channel

selection. It also selects the Virtual APs to which the settings apply. Any change to the AP

Profile affects all APs assigned to that profile.

Physical AP — represents the FortiAP units that the wireless controller has discovered.

There is one physical access point definition for each FortiAP unit. The Physical AP

configuration selects the AP Profile that applies that FortiAP unit.

Connecting the hardware

Connect all of the hardware as described below.

To connect the FortiAP unit to the wireless controller

1Connect Port 0 of one FortiAP unit to one of the Internal ports on the FortiGate unit.

2Connect Port 0 of the other FortiAP unit to the DMZ port on the FortiGate unit.

1After mounting the FortiAP unit, connect the Ethernet cable to Port 0 and connect the

power supply to the Power jack.

2Connect the WAN1 port of the FortiGate unit to the Internet.

3At each FortiAP unit, connect the power supply (or the power cable of the POE unit) to

the Power jack.

4Connect the power supply to the FortiGate unit.

The FortiGate supply is rated at 3A. The FortiAP supplies are 1.5A.

FortiAP™ Wireless Starter Kit Checking the firmware

Wireless Starter Kit Guide

01-420-139115-20110223 9

http://docs.fortinet.com/ • Feedback

Checking the firmware

You need to verify that the units have the appropriate firmware installed. If the firmware is

not correct, you can download and install appropriate firmware.

To verify the FortiGate unit firmware

1Connect a computer to one of the Internal ports.

2Use a browser to connect to http://172.16.1.1.

3Log in with user name “Admin” and password “fortinet”.

4Go to System > Dashboard > Status and check the Firmware version in System

Information.

If the build number is not 6390, see “Obtaining and installing the FortiGate firmware”,

next.

To verify the FortiAP unit firmware

1On the FortiGate unit, go to Wireless Controller > Configuration > Access Points.

2The FortiAP units should be listed. If necessary, select Refresh.

3If the Version column does not show build 112, see “Obtaining and installing the

FortiAP firmware” on page 10.

Obtaining and installing the FortiGate firmware

In FortiOS 4.0 MR2, only build 6390 supports wireless controller functionality. If your

FortiGate does not already have this firmware loaded, you need to download build 6390

from the Customer Support web site.

To get the wireless controller firmware for your FortiGate unit

1Log on to the Support web site at https://support.fortinet.com/.

2Go to Download > Firmware Images.

3Select FortiAP > v4.00 > 4.0MR2 > MR2_Patch_2 > Wireless_controller.

4Download the firmware build for your FortiGate model.

Installing the Starter Kit configuration FortiAP™ Wireless Starter Kit

Wireless Starter Kit Guide for FortiOS 4.0 MR2

10 01-420-139115-20110223

http://docs.fortinet.com/ • Feedback

To install the firmware on the FortiGate unit

1Log in to the FortiGate unit with user name “Admin” and password “fortinet”.

See “To verify the FortiGate unit firmware” on page 9 or see the unit’s QuickStart Guide

for more information.

2Go to System > Maintenance > Firmware and select Upgrade.

3Select Browse, find the firmware that you downloaded and then select OK.

Obtaining and installing the FortiAP firmware

The configuration of the Starter Kit is based on FortiAP firmware version 112. If this is not

the installed version on the FortiAP units, you need to download and install build 112.

To get FortiAP firmware

1Log on to the Support website at https://support.fortinet.com/.

2Go to Download > Firmware Images.

3Select FortiAP > v4.00 > 4.0MR2 > MR2_Patch_2.

4Download the file that corresponds to your model.

The Starter Kit contains FortiAP-220A units, FAP_22A_v4.2.0_b0112 is the correct file.

5Copy the file to a TFTP server accessible from your FortiGate unit.

To install the firmware on the FortiAP units

1Log in to the FortiGate unit with user name “Admin” and password “fortinet”.

See “To verify the FortiGate unit firmware” on page 9 or see the unit’s QuickStart Guide

for more information.

2Go to System > Dashboard > Status and enter the following command in the

CLI Console: (substitute your TFTP server IP address for x.x.x.x)

execute wireless-controller upload-wtp-image tftp

FAP_22A_v4.2.0_b0112 x.x.x.x

3After the upload completes, go to Wireless Controller > Configuration > Access Points,

select the FortiAP units and then select Reset All.

4After the reset completes, check that the Version column shows build 112.

Installing the Starter Kit configuration

The Starter Kit includes a configuration file which simplifies entering the correct

configuration settings into your FortiGate unit.

Obtaining the configuration file

The Customer Support site has a configuration file for a FortiGate-80CM with two FortiAP-

220A units. The configuration file can be modified for other FortiGate models.

To download a configuration file

1Log on to the Support web site at https://support.fortinet.com/.

2Go to Download > Firmware Images.

3Select FortiAP > StarterKit.

4Download StarterKit/Starter_Kit_FG-80CM_4.0MR2Patch1_20100916.zip.

5Expand the .zip file to obtain the configuration file FG-80-Starter_Kit_20100907.conf.

Tabla de contenidos

Otros manuales de Hardware de red de Fortinet

Fortinet

Fortinet FortiWAN 1000E Manual de usuario

Fortinet

Fortinet FortiLog-400 Manual de usuario

Fortinet

Fortinet FortiAnalyzer 800G Manual de usuario

Fortinet

Fortinet FortiGate FortiGate-ASM-FB4 Manual de instrucciones

Fortinet

Fortinet FortiGate 100F Series Manual de usuario

Fortinet

Fortinet FortiManager 1000C Manual de usuario

Fortinet

Fortinet FortiRecorder 7.0.0 Manual de instrucciones

Fortinet

Fortinet FortiGate 80F Series Manual de usuario

Fortinet

Fortinet FortiMail-100 Manual de usuario

Fortinet

Fortinet FortiAnalyzer 200D Manual de usuario

Fortinet

Fortinet FortiAnalyzer-4000B Manual de usuario

Fortinet

Fortinet 3000B Manual de usuario

Fortinet

Fortinet FortiAP 231FL Manual de usuario

Fortinet

Fortinet FortiGate 3700F Series Manual de usuario

Fortinet

Fortinet FortiGate 3000F Series Manual de usuario

Fortinet

Fortinet FortiAP 234G Manual de usuario

Fortinet

Fortinet FortiAnalyzer 3700G Manual de usuario

Fortinet

Fortinet FortiMonitor 100F Manual de usuario

Fortinet

Fortinet FortiToken-400 Manual de usuario

Fortinet

Fortinet FortiManager 200D Manual de usuario

Fortinet

Fortinet FortiGate-50AM Manual de usuario

Fortinet

Fortinet FortiNAC-CA-500F Manual de usuario

Fortinet

Fortinet FortiBridge-2001F Manual de usuario

Fortinet

Fortinet FortiWeb High-End Series Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario