Forte F3016MV2SS Manual de usuario

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Read these instructions completely and carefully.

•IMPORTANT – Save these

instructions for local inspector’s use.

•IMPORTANT – Observe all

governing codes and ordinances.

•Note to Installer – Be sure to leave these

instructions with the Consumer.

BEFORE YOU BEGIN •Note to Consumer – Keep these

instructions for future reference.

•Skill level – Installation of this appliance requires

basic mechanical and electrical skills.

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not

covered under the Warranty.

Installation

Instructions 30" Over the Range

Microwave Oven

F3016MV2SS

Before You Use Your Microwave

CONTENTS

General information

Important Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Damage – Shipment/Installation.............................. 4

Parts Included.......................................................... 4

Tools You Will Need ................................................ 5

Mounting Space ...................................................... 5

Step-by-step installation guide

6–8

Removing the Mounting Plate ...................... 6

Finding the Wall Studs.................................. 6

Determining Wall Plate Location.................. 7

Aligning the Wall Plate ................................ 8

Outside Top Exhaust

Attach Mounting Plate to Wall ............12

Preparation of Top Cabinet ................13

Checking for Proper Damper

Adapting Microwave Blower

Installation Instructions

Recirculating ........................................

Mount the Microwave Oven ................19

Preparation of Top Cabinet ................17

Attach Mounting Plate to Wall ............17

Outside Back Exhaust..........................16

Connecting Ductwork..........................15

Adjust the Exhaust Adaptor ................15

Operation............................................14

Outside Back Exhaust............................ 16–19

Adapting Microwave Blower for

Outside top Exhaust .......... 13–14........

Placement of The Mounting Plate ......................

............................ 12–15

Preparing Rear Wall for

Remove Blower Plate ...................... 16........

Charcoal Filter

Installing or Change the

Preparation of Top Cabinet ................20

Check Blower Plate ............................

.......................... 23

....................................22

Attach Mounting Plate to Wall............

–

Installation Types............................................... 9–22

for Outside Back Exhaust................17 18

–

Mount the Microwave Oven ..........21–

Hood Exhaust.................................................. 10 11

–

Mount the Microwave Oven ..........14 15

–

This product requires a three-prong grounded outlet.

The installer must perform a ground continuity check

on the power outlet box before beginning the

installation to insure that the outlet box is properly

grounded. If not properly grounded, or if the outlet

box does not meet electrical requirements noted

(under ELECTRICAL REQUIREMENTS), a qualified

electrician should be employed to correct any

deficiencies. CAUTION: For personal

safety, remove house fuse

or open circuit breaker

before beginning

installation to avoid severe

or fatal shock injury.

CAUTION: For personal safety, the mounting surface

must be capable of supporting the cabinet load, in

addition to the added weight of this 63–85 pound

(28.5–38.5 kg) product, plus additional oven loads of

up to 50 pounds (22.7 kg) or a total weight of

113–135 pounds (51.3–61.2 kg).

CAUTION: For personal safety, this product cannot

be installed in cabinet arrangements such as an island or

a peninsula. It must be mounted to BOTH a top cabinet

AND a wall.

NOTE: For easier installation and personal safety, it is

recommended that two people install this product.

IMPORTANT – PLEASE READ CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

The power cord of this

appliance is equipped with a

three-prong (grounding)

plug which mates with a

standard three-prong

(grounding) wall receptacle

to minimize the possibility

of electric shock hazard

from this appliance.

You should have the wall receptacle and circuit checked

by a qualified electrician to make sure the receptacle is

properly grounded.

Where a standard two-prong wall receptacle is

encountered, it is very important to have it replaced

with a properly grounded three-prong wall receptacle,

installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN EXTENSION CORD.

IMPORTANT SAFETY INSTRUCTIONS

ELECTRICAL

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 15 amps and

1.6 kilowatts. This product must be connected to a

supply circuit of the proper voltage and frequency.

Wire size must conform to the requirements of the

National Electrical Code or the prevailing local

code for this kilowatt rating. The power supply

cord and plug should be brought to a separate

15- to 20- ampere branch circuit single grounded

outlet. The outlet box should be located in the

cabinet above the microwave oven. The outlet box

and supply circuit should be installed by a qualified

electrician and conform to the National Electrical

Code or the prevailing local code.

Ensure proper

ground exists

before use

Installation Instructions

PART QUANTITY

Wood Screws 2

(1⁄4“ x 2“)

Toggle Bolts (and

wing nuts) (3⁄16“ x 3“)

Self-Aligning Machine 3

Screws (1⁄4“x31⁄4“)

Nylon Grommet

(for metal cabinets) 1

•If the unit is damaged in shipment, return the

unit to the store in which it was bought for repair

or replacement.

•If the unit is damaged by the customer, repair or

replacement is the responsibility of the customer.

•If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer

and installer.

DAMAGE—SHIPMENT/

INSTALLATION

Installation Instructions

PARTS INCLUDED

You will find the installation hardware contained in

a packet with the unit. Check to make sure you have

all these parts.

NOTE: Some extra parts are included.

HARDWARE PACKET

PART

QUANTITY

Templateand 1

Template

Installation 1

Instructions

Separately 2

Packed

Filters

PARTS INCLUDED (CONT.)

INSTALLATION

INSTRUCTIONS

ADDITIONAL PARTS

adaptor

Grease

Exhaust

Glass 1

Tray

Ring

Tru ntable

Cabinet

Combined T

Rear Wall

TOOLS YOU WILL NEED

# 1 Phillips screwdriver Pencil Ruler or tape measure and

straight edge Carpenter square

(optional)

Tin snips (for cutting

damper, if required) Electric drill with 3⁄16“,1⁄2“and 5⁄8“

drill bits

Hammer (optional)

Stud finder or

Filler blocks or scrap

wood pieces, if needed

for top cabinet spacing

(used on recessed bottom

cabinet installations only)

Gloves

Saw (saber, hole or keyhole)

Level Duct and masking tape

MOUNTING SPACE

NOTES:

•The space between the cabinets must be

30“(76.2 cm)wide and free of obstructions.

•If you are going to vent your microwave oven

to the outside, see Hood Exhaust Section for

exhaust duct preparation.

•When installing the microwave oven beneath

smooth, flat cabinets, be careful to follow the

instructions on the top cabinet template for

power cord clearance.

Bottom Edge of

Cabinet Needs to

be 30w(76.2 cm)

or More from the

Cooking Surface

Installation Instructions

Scissors

(to cut template, if necessary)

Safety goggles

Backsplash

66w(167.6 cm)

or More from

the Floor to the

Topofthe

Microwave

30“(76.2 cm)

“ (5.1 cm)

30“

(76.2 cm)

min.

161⁄2“ (41.9 cm)

13 Maximum (33 cm)

“

As a guide to installation, see page 24 for Mounting

Template Information.

Screws Screws

Mounting Plate

Find the studs, using one of the following

methods:

A. Stud finder – a magnetic device which

locates nails. OR

B. Use a hammer to tap lightly across the

mounting surface to find a solid sound.

This will indicate a stud location.

After locating the stud(s), find the center by

probing the wall with a small nail to find the edges

of the stud. Then place a mark halfway between

the edges. The center of any adjacent studs should

be 16w(40.6 cm) or 24w(61 cm) from this mark.

Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO

AT LEAST ONE WALL STUD.

Remove the installation instructions, filters, glass

Fold back all 4 carton flaps fully against carton

sides. Then carefully roll the oven and carton over

onto the top side. The oven should be resting in

the Styrofoam.

REMOVING THE MICROWAVE

OVEN FROM THE CARTON/

REMOVING THE MOUNTING

PLATE

FINDING THE WALL STUDS

PLACEMENT OF THE MOUNTING PLATE

Wall

Studs

Center

Carton

Pull the carton up and off the oven.

Remove the screws from the mounting plate.

This plate will be used as the rear wall template

and for mounting. Reinstall the screws into the

holes where they were removed.

Styrofoam

Installation Instructions

1tray and the small hardware bag.Do not remove

the Styrofoam protecting the front of the oven.

Cut the middle of the outer protective plastic bag to

remove the ounting late

DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

Installation Inst ructions

Draw a line on the

back wall equal to the

depth of the front

overhang.

33" to Cooktop

3/8"TOEDGE

%#76+10Ä+(':*#756#&#2614+5215+6+10'&1765+&'

4'%1//'0&'&&+/'05+10)4'#5'Ä.#&'0#+49+..

&+5%*#4)'+061*175'5647%674'

/+0+/7/9+&6*4'37+4'&

4'#49#..6'/2.#6'

NOTE:ITISVERYIMPORTANTTO

READANDFOLLOWTHEDIRECTIONS

INTHEINSTALLATIONINSTRUCTIONS

BEFOREPROCEEDINGWITHTHIS

REARWALLTEMPLATE.

ThisRearWallTemplateservest

opositionthebottom

mountingplateandtolocatethehorizontalexhaust

outlet.

1.Usealeveltocheckthatthetemplateispositioned

accurately.

2.Locateandmarkatleastonestudonthel

eftor

rightsideofthecenterline.

016'

Itisimportanttouseatleastonewood

screwmountedfirmlyinastudtosupporttheweight

ofthem

icrowave.Marktwoadditional,evenlyspaced

locationsforthesuppliedtogglebolts.

3.Drillholesint

hemarkedlocations.Wherethereis

astud,drilla3/16"holeforwoodscrews.Forholes

thatdonotlineupwithastud, drill5/8"h

olesfor

togglebolts.

016'

DONOTINSTALLTHEMOUNTINGPLATE

ATTHISTIME.

4.Removethetemplatefromtherearwall.

5.ReviewtheInstallationInstructionbookf

oryour

installationsituation.

Locateandmarkholestoalignwithholesi

nthe

mountingplate.

IMPORTANT:

LOCATEATLEASTONESTUDONEITHERSIDEOF

THECENTERLINE.

MARKT

HELOCATIONFOR2A

DDITIONAL,EVENLY

SPACEDTOGGLEBOLTSINT

HEMOUNTINGPLATE

AREA.

Locateandmarkholestoalignwithholesin the

mountingplate.

IMPORTANT:

LOCATEATLEASTONESTUDONEITHERSIDE OF

THEC

NTERLINE.

MARKTHELOCATIONFOR2ADDITIONAL,EVENLY

SPACEDTOGGLEBOLTSINTHEMOUNTINGPLATE

AREA.

Trimtherearwalltemplatealongthedottedline.

(%76176(14*14+<106#.

1765+&'':*#756

%76*1.'6*417)*4'#49#..(14':*#756#&#2614

12"

Darlevueltaalahojaparaconsultarla

versiónenEspañol.

3/8"TOEDGE

%#76+10Ä+(':*#756#&#2614+5215+6+10'&1765+&'

4'%1//'0&'&&+/'05+10)4'#5'Ä.#&'0#+49+..

&+5%*#4)'+061*175'5647%674'

/+0+/7/9+&6*4'37+4'&

4'#49#..6'/2.#6'

NOTE:ITIS VERY IMPORTANT TO

READAND FOLLOWTHE DIRECTIONS

INTHEINSTALLATIONIN

STRUCTIONS

BEFOREPROCEEDINGWITH THIS

REARWALL TEMPLATE.

ThisRearWall Template serves to positionthebottom

mountingplateandto locatetheho rizontal exhaust

outlet.

1.Usealevel to checkthatthetemplate is positioned

accurately.

2.Locateandmarkat leastonestudonthe leftor

right sideofthe centerline.

016'

Itis importanttou seatleast onewood

screwmountedfirmlyin a stu dtosupporttheweight

ofthemicrowave.Markt woadditional,evenlyspaced

locationsforthesuppliedtoggle bolts.

3.Drill holesin themarked locations. Where there is

a stud, drill a3/16" hole forwood screws.Forholes

that do not lineupwith astud, drill 5/8" holes for

toggle bolts.

016'

DONOTINSTALLTHEMOUNTINGPLATE

ATTHISTIME .

4.Removethetemplatefrom therearwall.

5.ReviewtheInstallationInstructionbook foryour

installationsituation.

Locateandmark holes to align withholesin the

mountingplate.

IMPORTANT:

LOCATEAT LEAST ONE STUDON EITHER SIDE OF

THECENTERLINE.

MARKTHELOCATIONFOR2ADDITIONAL,EVENLY

SPACEDTOGGLE BOLTS INTHE MOUNTINGPLATE

AREA.

Locateandma

rkholes to align withholesin the

mountingplate.

IMPORTANT:

LOCATEAT LEASTO

ESTUDON EITHER SIDE OF

THECENTERLINE.

MARKTHELOCATIONFOR2 ADDITIONAL, EVENLY

SPACEDTOGGLE BOLTSIN THEMO

UNTINGP

AREA.

Trimthe rear wall templatealong the dotted line.

Trimtherear walltemplate along thedotted line.

(%76176(14*14+<106#.

1765+&'':*#756

%76*1.'6*417)*4'#49#..(14':*#756#&#2614

12"

Darlevuelta ala hoja paraconsultarla

versiónenEspañol.

16-1/2

Atleast30

″

3/8"TOEDGE

%#76+10Ä+(':*#756#&#2614+5215+6+10'&1765+&'

4'%1//'0&'&&+/'05+10)4'#5'Ä.#&'0#+49+..

&+5%*#4)'+061*175'5647%674'

/+0+/7/9+&6*4'37+4'&

4'#49#..6'/2.#6'

NOTE:ITISV

ERYIMPORTANTTO

READANDFOLLOWT

HEDIRECTIONS

INTHEINSTALLATIONINSTRUCTIONS

BEFOREPROCEEDING WITHTHIS

REARWALL TEMPLATE.

ThisRearWallTemplate servesto positionthe bottom

mountingplateandtolocatethehorizontalexhaust

outlet.

1.Usealeveltocheckthatthetemplateispositioned

accurately.

2.Locateandmarkatleastonestudontheleftor

rightsideofthecenterline.

016'

Itisimportanttouseatleastonewood

screwmountedfirmlyinastudtosupporttheweight

ofthemicrowave.Marktwoadditional,evenlyspaced

locationsforthesuppliedtoggle bolts.

3.Drillholesinthemarkedlocations.Wherethereis

astud, drilla3/16" holeforwoodscrews.Forholes

thatdonotlineupwitha stud,drill 5/8"holesfor

togglebolts.

016'

DONOTINSTALL T HEMOUNTINGPLATE

ATTHISTIME.

4.Removethetemplatefromthe rearwall.

5.ReviewtheInstallationInstructionbookforyour

installations

ituation.

Locateandmarkholes toalign withholes in the

mountingplate.

IMPORTANT:

LOCATEATLEASTONESTUD ON EITHERSIDE OF

THECENTERLINE.

MARKTHE LOCATION FOR 2ADDITIONAL, EVENLY

SPACEDTOGGLEBOLTSINTHEMOUNTING PLATE

AREA.

Locateandmarkh

lestoalignwith holes inthe

mountingplate.

IMPORTANT:

LOCATEATLEAST ONESTUDON EITHER SIDE OF

THEC

NTERLINE.

MARKTHELOCATIONF

OR2ADDITIONAL,EVENLY

SPACEDTOGGLEBOLTSIN THE MOUNTING PLATE

AREA.

Trimtherear walltemplatealong the dotted line.

Trimtherear walltemplate along the dotted line.

(%76176(14*14+<106#.

1765+&'':*#756

%76*1.'6*417)*4'#49#..(14':*#756#&#2614

12"

Darlevueltaalahoja paraconsultar la

versiónenEspañol.

Your cabinets may have decorative trim that

interferes with the microwave installation. Remove

the decorative trim to install the microwave properly

and to make it level.

THE MICROWAVE MUST BE LEVEL.

Use a level to make sure the cabinet bottom is level.

If the cabinets have a front overhang only, with no

back or side frame, install the mounting plate down

the same distance as the front overhang depth. This

will keep the microwave level.

1.Measure the inside depth of the front overhang.

2.Draw a horizontal line on the back wall an equal

distance below the cabinet bottom as the inside

depth of the front overhang.

3.For this type of installation with front overhang

only, align the mounting tabs with this horizontal

line, not touching the cabinet bottom as described

in Step D.

Draw a vertical line on the wall at the center of the

30″wide space. Tape the Rear Wall Template

onto the wall matching the centerline and touching

the bottom of the cabinet.

33″to Cooktop

Draw a vertical line on the wall at the center of the

30″space.

Tape the Rear Wall Template onto the wall

matching the centerline and touching the bottom

cabinet frame.

3/8"TOEDGE

%#76+10Ä+(':*#756#&#2614+5215+6+10'&1765+&'

4'%1//'0&'&&+/'05+10)4'#5'Ä.#&'0#+49+..

&+5%*#4)'+061*175'5647%674'

/+0+/7/9+&6*4'37+4'&

4'#49#..6'/2.#6'

NOTE:ITI

SVERYIMPORTANTTO

READAND FOLLOWTHE DIRECTIONS

INTHEINSTALLATION INSTRUCTIONS

BEFOREPROCEEDINGWITHTHIS

REARWALLTEMPLATE.

ThisRearWallTemplateservesto positionthe bottom

mountingplateandtolocatethehorizontalexhaust

outlet.

1.Usea leveltocheckthat thetemplateispositioned

accurately.

2.Locateandmarkatleastonestudonthele ftor

rightsideo

fthecenterline.

016'

Itisimportant touseatleastone wood

screwmountedfirmlyi

nastudt

osupporttheweight

ofthemicrowave.Marktwoadditional,evenlyspaced

locationsforthesuppliedtogglebolts.

3.Drillholesinthemarkedlocations.Wherethere is

astud,drilla3/16" holefor woods

crews.Forholes

thatdo notline up withastud,drill5/8" holes for

togglebolts.

016'

DONOTINSTALLTHEMOUNTINGPLATE

ATTHISTIME.

4.Removethetemplatefrom therearwall.

5.ReviewtheI

nstallationInstructionbookforyour

installationsituation.

Locateand markholes to alignwith holes int

mountingplate.

IMPORTANT:

LOCATEATLEASTONESTUD ON EITHERSIDEOF

THECENTERLINE.

MARKTHELOCATIONFOR2 ADDITIONAL,EVENLY

SPACEDTOGGLEBOLTSIN THEMOUNTINGPLATE

AREA.

Locateand markh

olestoalign with holesin the

mountingp

late.

IMPORTANT:

LOCATEATLEASTONESTUDON EITHER SIDEOF

THECENTERLINE.

MARKTHE LOCATIONFOR2ADDITIONAL, EVENLY

SPACEDT

OGGLEBOLTS INTHE MOUNTINGP

LATE

AREA.

Trimtherearwalltemplatea

longthedottedline.

Trimther

earw

alltemplatealongthedottedline.

(%76176(14*14+<106#.

1765+&'':*#756

%76*1.'6*417)*4'#49#..(14':*#756#&#2614

12"

Darlevueltaa la hoja para consultar la

versiónenEspañol.

Plate position—beneath flat bottom

cabinet

Plate position—beneath recessed bottom

cabinet with front overhang

Plate position—beneath framed recessed

cabinet bottom

Installation Instructions

ALIGNING THE WALL PLATE

CAUTION: Wear gloves

to avoid cutting fingers on

sharp edges.

Area E Hole A

Hole B

Centerline

notches Draw a Vertical Line

on Wall from Center

of Top Cabinet

Draw a Horizontal line on wall from

bottom of “Rear Wall Template”.

Horizontal Line

3/8" TO EDGE

%#76+10Ä+(':*#756#&#2614+5215+6+10'&1765+&'

4'%1//'0&'&&+/'05+10)4'#5'Ä.#&'0#+49+..

&+5%*#4)'+061*175'5647%674'

/+0+/7/9+&6*4'37+4'&

4'#49#..6'/2.#6'

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING WITH THIS

REAR WALL TEMPLATE.

This Rear Wall Template serves to position the bottom

mounting plate and to locate the horizontal exhaust

outlet.

1. Use a level to check that the template is positioned

accurately.

2. Locate and mark at least one stud on the left or

right side of the centerline.

016'

It is important to use at least one wood

screw mounted firmly in a stud to support the weight

of the microwave. Mark two additional, evenly spaced

locations for the supplied toggle bolts.

3. Drill holes in the marked locations. Where there is

a stud, drill a 3/16" hole for wood screws. For holes

that do not line up with a stud, drill 5/8" holes for

toggle bolts.

016'

DO NOT INSTALL THE MOUNTING PLATE

AT THIS TIME.

4. Remove the template from the rear wall.

5. Review the Installation Instruction book for your

installation situation.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Locate and mark holes to align with holes in the

mounting plate.

IMPORTANT:

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE.

MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA.

Trim the rear wall template along the dotted line.

(%76176(14*14+<106#.

1765+&'':*#756

%76*1.'6*417)*4'#49#..(14':*#756#&#2614

12"

Darle vuelta a la hoja para consultar la

versión en Español.

Draw a Vertical line on the wall at the center of the

30" wide space.

Drill 5/8" holes for toggle bolts on 2 locations

(Hole A, Hole B) but if the location of hole

is same as that of stud, drill a 3/16" hole for wood

screw. In other words, toggle bolt can not be used

to the location of stud.

NOTE: DO NOT MOUNT THE PLATE AT THIS

TIME.

NOTE: Holes A and B are inside area E. If both of

A and B are not in a stud, find a stud somewhere in area

E and draw a forth circle to line up with the stud. It is

important to use at least one wood screw mounted

firmly in a stud to support the weight of the

microwave. Set the mounting plate aside.

2Draw a Horizontal line on the wall at the bottom of

“Rear Wall Template”.

INSTALLATION TYPES

This microwave oven is designed for adaptation to

the following three types of ventilation:

A.Outside Top Exhaust (Vertical Duct)

B.Outside Back Exhaust (Horizontal Duct)

C.Recirculating (Non-Vented Ductless)

proceed to that section.

OUTSIDE TOP EXHAUST

(VERTICAL DUCT) OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

RECIRCULATING

(NON-VENTED DUCTLESS)

See page 12

On models shipped for

recirculating exhaust, a

disposable charcoal filter

is factory installed to help

remove smoke and odors.

Adaptor in Place for

Outside Top Exhaust

Installation Instructions

Adaptor Must Be

Moved to the Back for

Outside Back Exhaust

NOTE: This microwave is shipped assembled for

Recirculating. Select the type of ventilation required

(Choose A, B or C)

for your installation and

See page 16

See page 20

EQUIVALENT NUMBER EQUIVALENT

DUCT PIECES LENGTH x USED = LENGTH

Rectangular-to-Round 5 Ft. (1.5 m) x ( ) = Ft. or m

Transition Adaptor*

Wall Cap 40 Ft. (12.2 m) x ( ) = Ft. or m

90° Elbow 10 Ft. (3 m) x ( ) = Ft. or m

45° Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m

90° Elbow 25 Ft. (7.6 m) x ( ) = Ft. or m

45° Elbow 5 Ft. (1.5 m) x ( ) = Ft. or m

Roof Cap 24 Ft. (7.3 m) x ( ) = Ft. or m

Straight Duct 6“ (15.2 cm) 1 Ft. (0.3 m) x ( ) = Ft. or m

Round or 31⁄4“ x 10“

(8.2 x 25.4 cm) Rectangular

Total Ductwork = Ft. or m

Equivalent lengths of duct pieces are based on actual tests

and reflect requirements for good venting performance with

any vent hood.

* IMPORTANT: If a rectangular-to-round transition

adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, in order

to allow free movement of the damper

NOTE: If you need to install ducts, note that the total

duct length of 31⁄4”x10”(8.2 x 25.4 cm) rectangular or

”(15.2 cm) diameter round duct

Outside ventilation requires a EXTERNAL EXHAUST

NOTE: It is important that venting be installed using

the most direct route and with as few elbows as possible.

This ensures clear venting of exhaust and helps prevent

blockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The exhaust adaptor has been designed to mate with

a standard 31⁄4”x10”(8.2 x 25.4 cm) rectangular duct.

If a round duct is required, a rectangular-to-round

transition adaptor must be used.

Maximum duct length:

For satisfactory air movement, the total duct length of

31⁄4”x10”(8.2 x 25.4 cm) rectangular or

6”(15.2 cm) diameter round duct should not

exceed120 equivalent feet (36.5 m).

Elbows, transitions, wall and roof caps,

etc., present additional resistance to airflow and are

equivalent to a section of straight duct which is longer

than their actual physical size. When calculating the total

duct length, add the equivalent lengths of all transitions

and adaptors plus the length of all straight duct sections.

The chart below shows you how to calculate total

equivalent ductwork length using the approximate feet

of equivalent length of some typical ducts.

Installation Instructions

INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING

DUCT.Read the following carefully.

(10.5” 5 cm)

should not exceed 120 equivalent feet (36.5 m).

diameter/ 6 (10.5” 5 cm)

diameter/

5 (10.5cm)/ 6 (15.2cm) diameter duct is acceptable to use

Otros manuales para F3016MV2SS

Tabla de contenidos

Otros manuales de Microondas de Forte

Forte

Forte F3015MVC5SS Manual de usuario

Forte

Forte F2413MV5SS Manual de usuario

Forte

Forte F2412MVD8SS Manual de usuario

Forte

Forte F2422MV5SS Manual de usuario

Forte

Forte F3015MVC5SS Manual de usuario

Forte

Forte F2413MV5SS Manual de usuario

Forte

Forte F3016MV2SS Manual de usuario

Forte

Forte F30MVTKSS Manual de usuario

Manuales populares de Microondas de otras marcas

Daewoo

Daewoo KOG-574R0S Manual de usuario

LG MH7040SS Manual de usuario

Sharp

Sharp R-895(AL)M Manual de usuario

Dometic

Dometic DOTRM13W Manual de usuario

Sanyo

Sanyo EM-X680 Manual de usuario

Sharp

Sharp R-393M Manual de usuario

KitchenAid

KitchenAid KMCX4510 Instrucciones de instalación

Smeg

Smeg S45MCX1 Manual de usuario

Russell Hobbs

Russell Hobbs RHM2044 Manual de usuario

Sunbeam

Sunbeam SMW759 Manual de usuario

Gallet

Gallet FMOE230S Manual de usuario

Bosch

Bosch CEG732X.1B Manual de usuario

Dometic

Dometic Roadmate 230 Manual de usuario

Samsung

Samsung SJ0396W Manual de usuario

Sanyo

Sanyo EM-P494WS Manual de usuario

Sharp

Sharp R-240 Manual de usuario

Electrolux

Electrolux EMS2840 Manual de usuario

Daewoo

Daewoo KOC-984T2S13 Manual de usuario