FORNI CLASSICO GAS 110 Manual de usuario

www.stefanoferraraforni.it

GAS OVEN

INSTALLATION AND OPERATING MANUAL

CLASSICO GAS 110 – 120 – 130 – 140 - 150

MLF GAS 110 – 120 – 130 – 140 – 150

SOMMA GAS 110 – 120 – 130 – 140 – 150

VULCANO GAS 110 – 120 – 130 – 140 – 150

PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING

THE APPLIANCE

A major cause of oven – related fire is failure to maintain required

clearances (air space) to combustible materials. It is of utmost

importance that this oven be installed only in accordance with these

instructions

SAVE THESE INSTRUCTIONS

Vers. 042022

Stefano Ferrara Forni S.R.L.

Forni artigianali napoletani

Neapolitan handmade brick ovens

Via Provinciale Pianura,2 – int.12

80078 Pozzuoli, Napoli

Tel./Fax: +39 081 876 1664

e-mail: info@stefanoferraraforni.it

P.IVA 06771801211

C.C.I.A.A. 838246

www.stefanoferraraforni.it

Table of content Page

- Introduction ............................................................................................................................................................. 3

- Installation operating and maintenance preface....................................................................................................... 5

- Features................................................................................................................................................................... 6

- Models and sizes ..................................................................................................................................................... 7

- Instruction for lifting and moving oven ..................................................................................................................... 9

- Packaging removing and placement oven on support stand ………………………………….... ................................ 11

- Installation procedures

•General information …………………………………………………………………………..... .......................... 12

•Stand covering installation (optional for Classico, Somma, Vulcano models)……………………………….. 13

•Stand covering installation for MLF model……………………………........................................................... 14

•Assembly of the burner............................................................................................................................... 18

- Connections

•Electrical connection ………………………………………………………………………….............................. 21

•Gas connection …………………………………………………………………………...................................... 22

- Sample of LPG system ……………………………… ................................................................................................ 24

- Oven venting …………………………………………………………………………………………….............................. 25

- Oven care during first fires …………………………………………………………………………… .............................. 26

- Use of the oven with wood ...................................................................................................................................... 27

•Maintenance and cleaning ......................................................................................................................... 28

- Burner components.................................................................................................................................................. 29

- Control panel............................................................................................................................................................ 30

- Celsius/Fahreneit change ....................................................................................................................................... 31

- First ignition and adjustmen

•First burner ignition ..................................................................................................................................... 32

•Burner unlock.............................................................................................................................................. 33

•Cooking temperature setting....................................................................................................................... 33

•Gas adjustment 1

. flame ........................................................................................................................... 34

•Adjust 1

. flame .......................................................................................................................................... 34

•Air adjustment 1

. flame ............................................................................................................................. 35

•Gas adjustment 2

. flame .......................................................................................................................... 36

•Air adjustment 2

. flame ............................................................................................................................ 36

•Setting safety limit temperature .................................................................................................................. 37

•Burner operation with control panel ............................................................................................................ 38

•ON/OFF second flame function .................................................................................................................. 38

•Manual/Automatic function.......................................................................................................................... 38

•Booster function.......................................................................................................................................... 39

•Switching the burner OFF through control panel ........................................................................................ 39

•Error messages .......................................................................................................................................... 40

- Maintenance ............................................................................................................................................................ 41

•Routine maintenance.................................................................................................................................. 42

•Special maintenance .................................................................................................................................. 43

- Burner gas conversion ............................................................................................................................................. 44

•Conversion on the control panel ................................................................................................................. 44

•Nozzles replacement .................................................................................................................................. 45

•Flame arrestor replacement........................................................................................................................ 47

- Replacing components ............................................................................................................................................ 47

•Sit control equipment replacement ............................................................................................................ 48

•Probe replacement .................................................................................................................................... 50

•Control Unit fuse replacement .................................................................................................................... 50

•Ignition detection electrode replacement .................................................................................................... 50

- Error messages........................................................................................................................................................ 51

- Troubleshooting ....................................................................................................................................................... 52

•Control panel doesn’t switch on.................................................................................................................. 52

•Control panel turns ON but the burner doesn’t start ................................................................................. 52

•Control panel turns ON, the spark strikes, F1 doesn’t turn ON and the burner blocks .............................. 52

•Control panel turns ON, F1 turns ON but the burner blocks and F1 turns OFF ......................................... 53

•Control panel turns ON, F1 turns On but after 15-20 seconds F2 does not turn ON ................................. 53

•Probe fault led turns ON ............................................................................................................................ 53

•Red display with “- - -”................................................................................................................................. 54

•Red display with T° inside the oven greater than the T° set on the green display ...................................... 54

•Green display: Set T° does not increase ................................................................................................... 54

•Slower heating than the normal parameters .............................................................................................. 55

•Soot under the dome ................................................................................................................................. 55

•Red display (T° inside the oven) exceeds the green display with 2

. flame led OFF ................................ 55

- Control unit diagram................................................................................................................................................. 56

- Connections diagram ............................................................................................................................................... 56

- Probe connections ................................................................................................................................................... 57

www.stefanoferraraforni.it

INTRODUCTION

This manual has been made so that the user of the oven can work in complete safety.

THE USER HAS OBLIGATION TO READ CAREFULLY AND TO OBSERVE CAREFULLY THE

INSTRUCTIONS OF THE MANUAL.

Failure to comply with the instructions contained in this manual, means to operate in the conditions of use

not foreseen by the manufacturer.

THE MANUFACTURER IS NOT LIABLE FOR ANY DAMAGES CAUSED BY THINGS OR PERSONS,

DUE TO THE FAILURE TO OBSERVE THE INSTRUCTIONS AND THE RECOMMENDATIONS IN THIS

MANUAL.

The manual must be kept in good condition and must always be available for quick reference in case of

need.

THE MANUAL IS OF OWNERSHIP OF THE MANUFACTURER AND CANNOT BE REPRODUCED EVEN

PARTIALLY, AS WELL AS IT CANNOT BE DIFFUSED OR USED FOR ADVERTISING PURPOSE OR

SHARED WITH THIRD PARTIES.

ANY TRANSGRESSION WILL HAVE CIVIL AND PENAL SANCTIONS AS A CONSEQUENCE.

EXPLANATION OF SYMBOLS AND WARNINGS

SYMBOL DESCRIPTION

Symbol used to identify information of particular importance within the manual. The

information also concerns the safety of the personnel involved in the use of the

machine.

Symbol used to indicate passages of technical importance in the instructions and

warnings or procedures related to operator safety.

Symbol used to indicate warnings or procedures related to electricity.

NOTE ON THE PRODUCT

The aim of the manufacturing company is to make ovens that meet the current technical state. So we always

take care of our products even after delivery.

For any problems or inconveniences contact the service center:

Email: info@stefanoferraraforni.it - tel. +39 081 876 16 64

www.stefanoferraraforni.it

INTRODUCTION ABOUT INSTRUCTIONS OF WORKING

These instructions have the task of allowing and facilitating the safe and appropriate use of the OVEN and of

exploiting the regulatory use possibilities provided.

Their observance helps to avoid dangers, repair costs, to reduce off-duty times and to increase the lifespan

of the device.

Operating instructions are to be followed also taking in consideration the regulations on accident prevention

and environmental protection valid in the country of installation

BUYER'S OBLIGATIONS

The buyer is obliged to:

• Observe the national regulations concerning workplace safety;

• Observe the instructions contained in the manual.

www.stefanoferraraforni.it

INSTALLATION OPERATING AND MAINTENANCE PREFACE

WARNING

READ THIS ENTIRE MANUAL BEFORE YOU INSTALL THE OVEN. FAILURE TO

FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY

INJURY, OR EVEN DEATH.

•When this oven is not properly installed, a fire may result. To reduce the risk of fire, follow the

installation instructions

•Contact your local building or fire officials for clarification on any restrictions on installation of this

oven in your area, or need for inspection of the oven installation.

•DO NOT close the oven door while a fire is in the oven.

•Place the door over the oven opening after cooking is completed at the end of the work day.

•Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

•Do not burn garbage or flammable fluids.

•Smokes of the burning must be expelled through a flue system conform to the local rules.

•Do not connect the oven to a chimney flue serving another appliance.

•Keep children and pets away from hot oven.

•DO NOT USE products not specified for use with this oven.

•DO NOT USE liquid fuel (firelighter fluid, gasoline, lantern oil, kerosene or similar liquids) to start or

maintain a fire.

•DO NOT use water to dampen or extinguish fire in the oven.

•Keep a proper extinguisher (class A) close to the oven at all times.

•Instruct all personnel about location and use of the fire extinguisher and proper fire emergency

procedures.

•DO NOT pack required air spaces with insulation or other materials.

•DO NOT expose the oven to the weather, if the oven is installed outdoors to shelter it under a

canopy.

•The oven is meant only for cooking pizza and/or bread it is not recommended for cooking other food

or food in pan ,chafe of metal pans can get the floor soon damaged and grease spatter from

roasting can be absorbed from the floor that lose its correct properties of cooking.

•In case of use of the oven with wood use only well dried wood.

•In case of use of the oven with wood, use a metal shovel to remove the ashes and place them in a

metal bin with a tightly fitting lid. The container should be stored on a non-combustible surface, away

from all combustible materials. Ensure ashes are completely cold before disposing of them

appropriately.

SAVE THESE INSTRUCTIONS

www.stefanoferraraforni.it

FEATURES:

Plain of cooking : Biscotto di Sorrento

Crown and dome :refractory bricks 60 mm. thick , they bear temperature of over 900°C (1650F)

External hood :Santa Maria Bricks modeled by hand.

External covering : Mosaic tiles – palladiana marble

Electronic burner with two modulating flames max thermal capacity Kw.34 – Kcal/h 29200

Electronic unit control for temperature management

Temperature range of working: 0°C – 500°C ( 32F – 392F)

Electronic unit control for temperature management

Alimentation : Gas

Gas consumption max. temp.:

- Natural gas: 3,50 Nmc/h

- LPG: 1,22 Nmc/h

Flue output : 250 mm.

Max heat output : 29000 kcal – 34 kw

Smokes temperature output : 190°C (374 F)

Extract air flow: 650 mc/h (at the time of starting)

500 mc/h (at the time of the oven fully operating)

Required CFM: 380

Venting : Natural draft

Electrical supply: 220 V – 50/60 Hz one phase

Electrical absorption :100 Watt.

Gas connection : ½ inch

Gas pressure : Natural gas : from 7 mbar - to 25 mbar

LPG : from 20 mbar - to 50 mbar

It’s required a direct connection of the tube at oven service from gas meter to the oven no other equipment

must be installed on the same line between the meter and the oven.

For the gas line use the follows pipes size:

- Distance from the gas meter to the oven until 10 meters (32 ft) use:

For LPG ½ “ pipe

For Natural gas ¾” pipe

- Distance from the gas meter to the oven over 10 meters (32 ft) use 1”pipe (independently to the

gas in use)

www.stefanoferraraforni.it

MODELS AND SIZES

CLASSICO

MLF

www.stefanoferraraforni.it

SOMMA

VULCANO

www.stefanoferraraforni.it

INSTRUCTIONS FOR LIFTING AND MOVING OVEN

FOR OVEN ALREADY INSTALLED ON THE SUPPORT STAND

1- USING A FORKLIFT

Determine if forklift capacity is sufficient to lift oven. (See pag. 7-8 for weights and sizes)

Prior to lifting, make sure the forks are long enough as whole diameter of the oven, if not fork extensions

should be used.

Keep forklift straight. Carefully place forks on the back of the oven through the stand legs

and position under the oven. Slowly lift and move the oven as needed

WARNING: MAKE SURE NOT TO DAMAGE THE BURNER DURING INSERTING THE

FORKS BETWEEN THE STAND LEGS.

2- USING A PALLET JACK

Determine if pallet jack capacity is sufficient to lift oven. (See pag. 7-8 for weights and sizes)

Prior to lifting, make sure pallet jack is long enough to reach both horizontal angles at lower end of steel tube

support legs. Place pallet jack on the back of the oven , place the forks between tube steel support legs

under horizontal angles.

Carefully lift oven and move slowly.

www.stefanoferraraforni.it

INSTRUCTIONS FOR LIFTING AND MOVING OVEN

FOR OVEN SEPARATED FROM THE SUPPORT STAND

1- USING A FORKLIFT

Determine if forklift capacity is sufficient to lift oven. (See pag. 7-8 for weights and sizes)

Prior to lifting, make sure the forks are long enough as whole diameter of the oven, if not fork extensions

should be used.

Under the oven there are four little steel feet 4” (10 cm) high to permit placing of the forks.

Keep forklift straight. Carefully place forks on the back of the oven through the steel feet and position under

the oven. Slowly lift and move the oven as needed.

2- USING A PALLET JACK

Determine if pallet jack capacity is sufficient to lift oven. (See pag.8 for weights and sizes)

Prior to lifting, make sure the forks are long enough as whole diameter of the oven.

Place pallet jack on the back of the oven, place the forks between the steel feet and position under the oven.

Carefully lift oven and move slowly.

WARNING : STRICTLY FORBIDDEN TO INVERT THE OVEN ALSO ON A SIDE , ONLY

VERTICAL LIFTING IS ALLOWED

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Horno de FORNI

FORNI

FORNI FEM207SC Manual

FORNI

FORNI Gennarino 100 E Manual de usuario

FORNI

FORNI GENNARINO Manual de usuario

FORNI

FORNI Gennarino 80 Manual de usuario

Manuales populares de Horno de otras marcas

Bosch

Bosch HVA531NS0 Manual de usuario

Electrolux

Electrolux EOF6P46X Manual de usuario

NEFF

NEFF B44S32 5GB Series Manual de usuario

Combi

Combi BLODGETT BC142GDS Manual de usuario

AEG

AEG COMPETENCE 311704300 Manual de usuario

Falcon

Falcon DOMINATOR PLUS G3106 Series Guía del usuario

Rational

Rational SCC WE 61G Manual de usuario

Smeg

Smeg DOSPA38X Manual de instalación y operación

Electrolux

Electrolux air-o-convect 20 GN 2/1 Manual de usuario

Miele

Miele HR 1954-2 Manual de usuario

KHIND

KHIND OT50 Manual de usuario

Henny Penny

Henny Penny Smoker Box Manual de usuario

Lang

Lang ECOD-AP Manual de usuario

AEG

AEG BEK455310M Manual de usuario

Frigidaire

Frigidaire FNGE90JGR Manual de usuario

Hotpoint

Hotpoint FE9 S831 JSH IX Manual de usuario

GE Advantium SCB2000 Manual de usuario

AEG

AEG DE401301DM Manual de usuario