FONESTAR TFA-500 Manual de usuario

TFA-500

100 V LINE TRANSFORMER

FOR AMPLIFIERS

EN Instruction manual

- 2-

We take this opportunity to thank you for buying this product.

We recommend you read the instruction manual before switching on the machine and follow the instructions

that are given. Keep the manual for future reference.

SECURITY AND T E ENVIRONMENT

ELECTRICAL SECURITY

Check that the current in the mains connection where the machine is to be installed corresponds to the

power supply of the machine.

To avoid damaging the equipment, electrical shocks, ﬁre or physical injury when you connect or disconnect

the equipment from the power supply, pull the plug ﬁrmly out of the mains socket holding the plug, never the

cable.

Always do this with dry hands.

Keep the power supply cable far from sources of heat. Do not put heavy objects on top of it or change it.

Clean dust and dirt off the power supply cable regularly.

Do not open the machine; you could get an electric shock.

CAUTION

While installing the machine, make sure it is switched off and unplugged.

Do not open the machine. Touching the internal parts is dangerous and you could receive an electric shock.

The machine must not be splashed or dripped on. Never place recipients with liquid inside on the machine.

Do not place anything inside the machine.

LOCATION

Place the equipment on a horizontal surface with enough space around it to allow ventilation.

Avoid direct sunlight, heat sources and excessive dust.

Do not place the machine near magnetic ﬁelds or static electricity.

Do not use surfaces which vibrate or receive impact.

Do not pile machines on top of one another.

VENTILATION

Never block or cover the ventilation slits on the machine.

Do not expose it to direct sunlight or place it near sources of heat.

PERIODS OF INACTIVITY

When the machine is not going to be used for a long period of time, disconnect it from the mains.

If you are using an adapter, take into account that it will continue using electricity even if the machine is

switched off. If it is not going to be used for a long period of time, disconnect it from the mains.

T E ENVIRONMENT

To save energy, switch the machine off when you are not going to use it for a long time. The machine could

contain substances that are harmful to the environment or human health. To minimize the effect of these

substances the machine must be correctly managed and recycled when you decide to dispose of it.

When you dispose of it remember: it cannot be thrown into a conventional rubbish bin.

If it contains or uses batteries, these must be disposed of separately.

The machine (without batteries) must be disposed of correctly. Put it in a container specially intended for the

collection of electronic and electrical appliances, at the dump or hand it over to the dealer when you purchase

similar equipment, so that the dealer can dispose of it correctly (at no added cost).

- 3-

SIGNIFICANCE OF THE SYMBOLS ON THE MACHINE*

The symbol formed by the expression “Class 1 laser product” written in a rectangle

indicates that visible or invisible laser radiation could be produced. Avoid direct exposure

to the laser.

The symbol formed by a ray of lightening inside a triangle shows that the machine has

connection terminals or a circuit with areas with a current which could cause an electric

shock, even in normal working conditions.

The symbol formed by an exclamation mark in a triangle shows that the instruction manual

must be referred to for information on how the machine works and its use.

The symbol formed by one square inside another square shows that the machine has

double electrical insulation.

The European Community symbol shows that the machine complies with the current

European Union legislation, as well as its transposition to local legislation.

The symbol of a rubbish bin crossed out and over a horizontal line shows that when the

product is disposed of it must be done properly, placing it in a special selective electronic

and electrical equipment container or through a dealer when purchasing a similar product,

at no additional cost. It also shows that the machine was put on the market after 13th

August 2005 (European Community Directive 2002/96/CE of Electrical and Electronic

recycling, and its Spanish equivalent R.D.208/2005).

In accordance with what is set out in the aforementioned decree, FONESTAR is registered

in the RAEE (Registro de Aparatos Eléctricos y Electrónicos) in a special section REI

(Registro de establecimientos Industriales), with the entry number 001851.

The symbol Ro S (Restriction of azardous Substances) shows that the product has been

designed and manufactured restricting the use of certain dangerous materials (Directive

2002/95/EC on the restriction of certain dangerous substances in electrical and electronic

appliances, and its transferal to the Spanish regulations, R.D.208/2005).

*It is possible that some of these symbols do not appear on the machine.

EXEMPTION OF LIABILITY

The characteristics of the equipment and the content of the manual can change without forewarning.

FONESTAR, S.A. does not assume responsibilities regarding the inappropriate use of the equipment or the

information supplied in this instruction manual, and speciﬁcally disclaims any implied liability for marketability

or ﬁtness for any other use.

DESCRIPTION

The TFA-500 is a 100 V line transformer for ampliﬁers. It converts an ampliﬁer or 4-8 Ω low impedance stereo

power amp output into a high impedance output for speakers 100 or 70 V line transformer.

Low impedance and 100 V line speakers can be connected at the same time.

It is perfect for P.A. applications and background music when a large number of speakers need to be

connected to just one ampliﬁer.

-4-

CONTROLS AND FUNCTIONS

FRONT PANEL

1.- INPUT 1: LED indicator that lights up when a signal is detected in INPUT 1.

2.- INPUT 2: LED indicator that lights up when a signal is detected in INPUT 2.

BACK PANEL

1.- OUTPUT 2: 100 and 70 V line high impedance speaker output terminals for channel 2. Only use one of

the output lines.

2.- OUTPUT 1: 100 and 70 V line high impedance speaker output terminals for channel 1. Only use one of

the output lines.

3.- STEREO/BRIDGE MONO: selector for choosing the operating mode. You can choose between stereo

mode (2 stereo input channels or 2 individual input channels, in INPUT 1 and INPUT 2) and mono bridge

mode (just 1 input channel, in INPUT 1).

4.- INPUT 2: INPUT 2 signal input connector. For connecting the output signal of one channel from the low

impedance ampliﬁer.

5.- INPUT 1 BRIDGE MONO: INPUT 1 signal connector. For connecting the output signal of one channel

from the low impedance ampliﬁer. Use this input if you are going to select bridge mode.

-5-

CONNECTION

Note: to avoid damage, the power of the input signals connected to INPUT 1 and INPUT 2 must not

exceed the power supported: 500 W RMS per channel in stereo mode or 1000 W RMS in mono bridge

mode.

Stereo mode

In this application, a low impedance stereo ampliﬁer is used together with the TF-500 to get two 100 or 70

V lines.

Place the STEREO/BRIDGE MONO selector in the STEREO position.

Connect both of the low impedance ampliﬁer stereo output channels to INPUT 1 or INPUT 2.

Connect the speaker line to the speaker output. Use the 100 or 70 V line output in accordance with the type

of speakers you are going to connect. Use only one of the output lines.

All the speakers must be connected in parallel and the sum of the power of all the speakers must not exceed

the power supplied by the TFA-500.

-6-

Two speaker zones

In this application, two ampliﬁers in low impedance mono bridge mode are used together with the TFA-500 to

get 2 independent 100 or 70 V lines.

Place the STEREO/BRIDGE MONO selector in the STEREO position.

Connect the mono output channel from each low impedance ampliﬁer to the INPUT 1 and INPUT 2 inputs.

Connect the speaker line to the speaker output. Use the 100 or 70 V line output in accordance with the type of

speakers that you are going to connect. Only use one of the output lines.

All the speakers must be connected in parallel and the sum of the power of all the speakers must not exceed

the power supplied by the TFA-500.

-7-

Mono bridge mode

In this application a low impedance ampliﬁer is used in mono bridge mode together with the TF-500 to

achieve 2 x 100 or 70 V lines with the same signal.

Place the STEREO/BRIDGE MONO selector in the BRIDGE MONO position.

Connect the mono output channel from the low impedance ampliﬁer to the INPUT.

Connect the speaker line to the speaker output. Use the 100 or 70 V line output in accordance with the type

of speakers that you are going to connect. Use just one of the output lines.

All the speakers must be connected in parallel and the sum of the power of all the speakers must not exceed

the power supplied by the TFA-500.

-8-

Stereo mode, 8 Ω and 100 or 70 line

In this application, a low impedance stereo ampliﬁer is used together with the TFA-500 to connect a pair of

low impedance (8 Ω) speakers and speakers with 100 or 70 V line transformer.

-9-

SPECIFICATIONS

TFA-500

CHARACTERISTICS 100 V line transformer for ampliﬁers. Converts an ampliﬁer or a

low impedance (4-8Ω) stereo powered ampliﬁer output into a high

impedance output for speakers with 100 or 70 V line transformer.

Allows simultaneous connection of low impedance and 100 V line

speakers.

STEREO POWER 500 + 500 W RMS

BRIDGE MODE POWER 1000 W RMS

RESPONSE 20-20 000 z

DISTORTION < 0.1%

PROTECTION Temperature, over current and RF ﬁlter

INDICATORS Input signal

INPUTS 2 inputs, 4-8 Ω, screw terminals and banana plugs

SPEAKER OUTPUT 100 and 70 V lines, screw terminals, stereo or bridge mode

selectable

DIMENSIONS 483 x 72 x 236 mm depth. Approximately 1.5 x 19" U rack

WEIGHT 8.7 kg

DECLARATION OF CONFORMITY

The 100 V line transformer for ampliﬁers model TFA-500 complies with the European Community directives

2004/108/EC on Electromagnetic Compatibility and 2006/95/EC on Low Voltage.

Santander, 15th December 2009

Juan Vallejo

Technical Engineer, Sales Department

WARRANTY

This product has been tested and has passed the corresponding quality control prior to being put on the market.

FONESTAR guarantees the suitability of the product for its speciﬁed use during a period of 2 years from the

delivery date and commits itself to repair or substitute the goods as expressed in the Spanish law ‘La Ley

General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.

The lack of conformity in the ﬁrst six months after purchase, due to a manufacturing defect, will be rectiﬁed with

no more than showing the proof of purchase. After six months FONESTAR reserves the right to demand proof of

the product being sold with that problem.

This warranty does not include damage produced by: inappropriate use or negligence, accidents, worn out parts

due to use, breakages, burns, spilt liquids or other substances, excessive humidity, battery deterioration and

internal manipulation of the device, the software or its components by unauthorized persons, and in general any

use that is unrelated to the nature and purpose of the product.

If any service is needed during the warranty period because of lack of conformity, please contact the business or

distributor where the product was purchased in no more than 2 months after being conscious of the problem. It

is only necessary to contact FONESTAR if it is impossible or imposes an undue burden for them to solve it.

To beneﬁt from this warranty it is necessary to show the proof of purchase with the date clearly visible, with no

corrections or crossing out.

This document adds information, and never decreases the consumers’ rights, which in all cases are protected by

the Spanish law ‘La Ley General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo

1/2007 16 Noviembre.

FONESTAR is a member of ECOEMBALAJES ESPAÑA, S.A. “ECOEMBES”, with number 03497

and all our products carry the symbol, backed by our membership and subscription to the above

mentioned organization with the recycling and subsequent management of our packaging.

FONESTAR S.A. - NIF A28780443 - Apartado 191 - 39080 - Santander, Cantabria, (Spain)

www.fonestar.com

- 10 -

Otros manuales para TFA-500

Tabla de contenidos

Otros manuales de Transformador de FONESTAR

FONESTAR

FONESTAR CV-1720 Manual de usuario

Manuales populares de Transformador de otras marcas

RAM

RAM TUS404 Manual de usuario

Ortofon

Ortofon ST-80 SE Manual de usuario

Siemens

Siemens GEAFOL Neo Manual de usuario

Uhlenbrock Elektronik

Uhlenbrock Elektronik 28000 Manual de usuario

Monacor

Monacor PATL-100/XC Manual de usuario

Delta Electronics

Delta Electronics Current Sense Transformers TCE1906H Manual de usuario

Hobart

Hobart 6T28-600CL Manual de usuario

Shinkawa

Shinkawa LS Series Manual de usuario

Huawei

Huawei JUPITER-3000K-H1 Manual de usuario

Monacor

Monacor IMG STAGELINE LTR-102 Manual de usuario

Lionel

Lionel ZW Manual de usuario

Enapter

Enapter Electrolyser Manual de usuario

MKC

MKC SET-2010 Manual de usuario

ABB

ABB Relion 615 series Manual de usuario

Monacor

Monacor Security TVI-200 Manual de usuario

Arteche

Arteche KA Manual de usuario

Sygonix

Sygonix 2522120 Manual de usuario

Digital Acoustics

Digital Acoustics IP7-SS40 Manual de usuario