Follett U300 Series Manual de usuario

Installation Manual

Service Numbers Below B22204

U300/UD300 Series Ice

and Beverage Dispensers

208601R01

801 Church Lane • PO Box D, Easton, PA 18044, USA

Toll free (800) 523-9361 • (888) 2-FOLLETT

(610) 252-7301 • Fax (610) 250-0696 • www.follettice.com

Model U300

Model U300B

Model U300R400A/W

Model U300BR400A/W

Model U300R800A/W

Model U300BR800A/W

Model UD300 Model UD300R400A/W Model UD300R800A/W

Single-sided dispensers

Dual-sided dispensers

Order parts online

www.follettice.com

Welcome to Follett

Follett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability and

outstanding after-the-sale support. To ensure that this dispenser delivers that same degree of service, we ask

that you take a moment to review this manual before beginning installation of the dispenser.

Should you have any questions or require technical assistance at any point, please call our technical service

group toll free at (800) 523-9361 or (888) 2-FOLLETT or (610) 252-7301.

Before you begin

•After uncrating and removing all packing material, inspect the equipment for concealed shipping damage.

If damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in

filing a claim, if necessary.

•Check your paperwork to determine which model you have. Follett model numbers are designed to

provide information about the type and capacity of Follett ice dispensing equipment. Following is an

explanation of the different model numbers.

U300BR400A

Condenser type – A = air-cooled, W = water-cooled

Remote icemaker(s) capacity and refrigerant – 400 = 400 lbs (181kg)/day, R404A

800 = 800 lbs (363kg)/day, R404A

absence of = manual fill unit

B = beverage bath equipped. Absence of a B = no integral beverage cooling

Approximate manual load storage capacity in lbs

Dispenser configuration – U = undercounter, UD = undercounter dual-sided

Important cautions

•Storage area of dispenser contains mechanical, moving parts. Keep hands and arms clear of this

area at all times. If access to this area is required, power to unit must first be disconnected.

•Follett manual load dispensers can accommodate most cube/cubelet ices up to 1" square and

compressed nugget ice. Nugget, crushed, flake, bagged or congealed ice cannot be used. Use of

these ices can jam dispenser and void warranty. Separate any “waffle-like” sections of cubes

before adding to dispenser. For ice compatibility questions, please call Follett customer service

at (800) 523-9361 or (888) 2-FOLLETT or (610) 252-7301.

•Follett recommends use of an activated carbon filter for units equipped with icemakers

•Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.

•Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.

Electrical specifications – 115V, 60Hz, 1 phase

• Maximum fuse size 15 amps, each circuit all models

• Equipment ground required

• Electric disconnect suggested within 10 ft (3m) of dispenser and icemaker(s)

Single-sided dispensers

U300 – dispenser 6.0 amps

U300B – dispenser 7.0 amps

U300R400A/W – dispenser 6.0 amps, icemaker 11.0 amps

U300BR400A/W – dispenser 7.0 amps, icemaker 11.0 amps

U300R800A/W – dispenser 6.0 amps, icemakers 11.0 amps each

U300BR800A/W – dispenser 7.0 amps, icemakers 11.0 amps each

Dual-sided dispensers

UD300 – dispenser 8.0 amps

UD300R400A/W – dispenser 8.0 amps, icemaker 11.0 amps

UD300R800A/W – dispenser 8.0 amps, icemakers 11.0 amps each

Plumbing

Caution: Do not reduce size of drain lines or tie drains together.

Dispenser 3/4" slip fit PVC bin drain

1" PVC slip fit drain pan drain(s)

1" PVC slip fit beverage bath drain (units with beverage cooling)

Note: Drains should be hard piped and insulated. Maintain at least 1/4" per foot slope

(6mm per 304mm run) on drain line run.

Icemaker Refer to Icemaker Installation Manual packed with icemaker for installation instructions

1/4" FPT water in

1/2" MPT drain

3/8" FPT condenser inlet (water-cooled condenser only)

1/2" FPT condenser drain (water-cooled condenser only)

Note: Water disconnect within 10 ft (3m) of dispenser is suggested for auto load units.

Beverage connections

Dispenser type Syrup lines Carbonator manifold Plain water lines

Single-sided models 1/4" barb 3/8" barb 1/4" barb

Dual-sided models Pigtail connections provided at base of dispenser

1/4" hose 3/8" hose 1/4" hose

On all models with remote icemaker(s), black wire on icemaker control board

LINE VAC terminal must be moved to 24V terminal.

entrance

beverage

lines

electric

conn.

17"

(432mm)

12" min

(305mm)

6" min

(153mm)

one icemaker –

models U300R400A/W

U300BR400A/W

two icemakers –

models U300R800A/W

U300BR800A/W

40.875

(1039mm)

54.875"

(1394mm)

25.25"

(642mm)

29.625"

(753mm)

ICE

disp.

drains

18.875"

(480mm)

Front view

Side view

U300 series single-sided dispensers

22"

(559mm)

30"

(762mm)

beverage

lines enter

through

bottom

(229mm)

15"

(381mm)

10"

(254mm)

2.5"

(64mm)

7" (178mm)

3" (77mm)

(51mm)

junction

boxes

32.375"

(823mm)

ice waterbath

(U300BR400A/W,

U300BR800A/W,

U300B only)

3/4"

(19mm)

drain

(26mm)

drains

8.5"

(216mm)

ice

transport

tube entry

27.5"

(699m

Required clearances

•60" (1524mm) above counter for installation if dispenser will be

dropped into counter

•49" (1245mm) above counter for all units after installation for

auger cleaning and servicing

•12" (305mm) on dispense chute side of all models for connections

•12" (305mm) on side opposite dispense chute if ice transport tube

enters side opposite chute

12.125"

(308mm)

30"

(762mm)

8.5"

(216mm)

(229mm)

15"

(381mm)

27.5"

(699mm)

2.5"

(64mm)

(51mm)

3/4"

(19mm)

drain

ice

tube

entry

32.375"

(823mm)

(26mm)

drains

8.5"

(216mm)

electric

conn.

18.875"

(480mm)

17"

(432mm)

12" min.

(305mm)

6" min.

(153mm)

dispenser with one icemaker

models UD300R400A/W

dispenser with two icemakers

models UD300R800A/W

disp.

drains

43.875

(1115mm)

54.875"

(1394mm)

25.25"

(642mm)

29.625"

(753mm)

ICE

beverage

lines exit

through

bottom of

chase

12" min.

(305mm)

dispenser only with no

icemaker

model UD300

Front view

Ice dispense chute side

UD300 series dual-sided dispensers

beverage

lines exit

through

bottom of

chase

27.5"

(699mm)

10"

(254mm)

alt. ice

transport

tube entry

13.25"

(337mm)

13.25"

(337mm)

electric

conn.

Side opposite dispense chute

Required clearances

•60" (1524mm) above counter for installation, if dispenser will be dropped into counter

•49" (1245mm) above counter for all units after installation for auger cleaning and servicing

•12" (305mm) on dispense chute side of all models for connections

•12" (305mm) on side opposite dispense chute, if ice transport tube enters side opposite chute

•12" (305mm) on side opposite dispense chute on all dual-sided dispensers for connections

Model

U300

U300B

UD300

U300R400A/W

U300BR400A/W

UD300R400A/W

U300R800A/W

U300BR800A/W

U300R800A/W

Electrical Connection

•Hard wiring of dispenser

required

•Dispenser power – hard wiring

required

•Bin signal – cord and plug

supplied

•Icemaker – cord and plug

supplied on power and bin

signal

•Dispenser power – hard wiring

required

•Bin signal – cord and plug

supplied

•Icemaker – cord and plug

supplied on power and bin

signal

Circuit(s) required

115V, 60Hz, 1 phase

Max. fuse dispenser – 15 amps.

115V, 60Hz, 1 phase

(2) circuits required

•Dispenser – 15 amps max. fuse

size

•Icemaker – 20 amps max. fuse

size

115V, 60Hz, 1 phase

(3) circuits required

•Dispenser – 15 amps max. fuse

size

•(2) icemakers – 20 amps max.

fuse size each

Note: equipment must be wired according to local and NEC codes.

Attention – Should local codes require a hard-wired connection and/or shielded wiring,

eliminate the cord(s) and plug(s) and follow the appropriate field wiring diagram on the

following page.

See Icemaker Installation and Operation manual for recommended junction box preparation of

hard-wired remote icemaker(s).

Electrical hookup information

Field wiring diagram – manual load models

Field wiring diagram – automatic load models

Electric Power Source Standard electrical - 115V, 1 Ph, 60Hz,

max. fuse size 20 amps

GND

GRN

GND

GRN

LEGEND

WIRENUT FIELD

CONNECTIONS

XEQUIPMENT

GROUND

B - BLACK

W - WHITE

GRN - GREEN

LEFT JUNCTION BOX

FIELD WIRING DIAGRAM IS

INTENDED TO AID ELECTRICIAN

OR TECHNICIAN IN UNDERSTANDING

HOW EQUIPMENT WORKS. ALL FIELD

WIRING MUST BE INSTALLED IN

ACCORDANCE WITH NEC AND LOCAL

ELECTRICAL CODES.

IMPORTANT

20 AMP FUSED

DISCONNECT RIGHT JUNCTION BOX

U300 DISPENSER

NOT USED

BL - BLUE

Y - YELLOW

Standard electrical - 115V, 1 Ph, 60Hz,

max. fuse size 20 amps

LEGEND

WIRENUT FIELD

CONNECTIONS

XEQUIPMENT

GROUND

B - BLACK

W - WHITE

GRN - GREEN

LEFT JUNCTION BOX

FIELD WIRING DIAGRAM IS

INTENDED TO AID ELECTRICIAN

OR TECHNICIAN IN UNDERSTANDING

HOW EQUIPMENT WORKS. ALL FIELD

WIRING MUST BE INSTALLED IN

ACCORDANCE WITH NEC AND LOCAL

ELECTRICAL CODES.

IMPORTANT

Electric Power Source

GND

GRN

GND

GRN

20 AMP FUSED

DISCONNECT RIGHT JUNCTION BOX

U300 DISPENSER

ELECTRIC POWER SOURCE

GND

GRN

GND GRN

20 AMP FUSED

DISCONNECT

GND

GRN

GND GRN

20 AMP FUSED

DISCONNECT

ICEMAKER #1

LOWER JUNCTION BOX

ICEMAKER #2 (OPTIONAL)

UPPER JUNCTION BOX

BL - BLUE

Y - YELLOW

On all models with remote

icemaker(s), the black wire on the

icemaker control board LINE VAC

terminal must be moved to the

24V terminal.

ADA collar details and installation requirements

All units

1. Make counter cut-out in accordance with instructions on page 8.

2. If not using legs, block up area below counter cut-out to support dispenser.

Procedure for dispensers that will be dropped into a four-sided cut-out:

3. Center collar over counter cut-out opening.

4. If dispenser is equipped with an icemaker, disconnect ice transport tube from its bracket in storage area of

dispenser (if tube enters opposite from tower).

Note: Since this tube must be reinstalled in bracket after dispenser is dropped into counter, note how tube is

held by bracket tabs before disconnecting.

5. Carefully lower dispenser into counter cut-out as described on page 8, adjusting height of dispenser from

below until dispenser flange rests flush on collar and is supported by legs or blocks.

Procedure for dispensers that will be slid into a three-sided cut-out:

3. Slide collar over bottom of dispenser and hold against dispenser counter flange.

4. Carefully slide dispenser into position, keeping ice transport tube clear of counter supports.

5. Adjust height of dispenser from below until dispenser flange rests flush on collar and is supported by legs or

blocks.

All units

6. Apply a bead approximately 1/4" (6mm) in diameter of NSF-listed silicone sealant (Dow Corning RTV-732 or

equivalent) around perimeter of dispenser where it meets collar and smooth sealant to a 1/8" (4mm) radius.

7. Proceed with electrical, plumbing (and ice tube connections on automatic load units) as described beginning

on page 8.

If dispenser is to be installed in a 34" (864mm) high counter for ADA compliance, a

.9" (23mm) stainless steel “collar” must be installed between dispenser and counter

to provide necessary clearance. Standard 36" (915mm) counters do not require this

accessory piece. If you need this collar and it was not included with dispenser,

please call Follett to obtain it.

All U300/UD300 dispensers must be installed level in both directions to ensure

proper operation and must be supported from below with supplied 6" (153mm) legs,

or with channels installed at site. Do not hang dispenser on flange. These

dispensers weigh approximately 325 lbs (147kg). Use care when maneuvering unit

into position.

Installing U300/UD300 series dispenser in counter

1. After determining that the dispenser location will meet all requirements detailed in this manual, cut counter for

slide-in or drop-in installation as shown in drawings below. Shaded area on drawings depicts slide in from rear

of counter, however dispensers may be slid into counter from any side.

2. If legs will be used, carefully block up dispenser and install set of 6" (153mm) legs.

3. For slide-in installations, carefully slide dispenser into position.

4. For drop-in installations only, rig dispenser for hoisting with a mechanical lift and carefully lower dispenser

into counter until dispenser rests on support blocks or legs. USE SPREADER BARS TO KEEP HOISTING

ROPES AWAY FROM UPPER SECTION OF DISPENSER. DO NOT HOIST BY TOWER OR RAIL

SECTION! MUST REMOVE HANDLE TO FIT IN COUNTER.

5. Shim support members or adjust legs until dispenser flange rests lightly on counter.

6. Apply a bead approximately 1/4" (6mm) in diameter of NSF-listed silicone sealant (Dow Corning RTV-732 or

equivalent) around perimeter of dispenser where it meets counter and smooth sealant to a 1/8" (4mm) radius.

7. Install hard drain lines for all drains, maintaining at least a 1/4" per foot slope (6mm per 304mm run)

and insulate lines to prevent condensation.

8. Make electrical connections in accordance with applicable wiring diagrams on page 6 and chart on page 5, as

well as NEC and local codes. Provide disconnects within 10 ft (3m) of dispenser and icemaker for service

purposes.

Min.

33"

(839mm)

flat

surface

30.375"

(772mm)

38.5"

(978mm)

42.5"

(1080mm)

11.625"

(296mm)

11.625"

(296mm)

7.125"

(181mm)

Plan view

UD300 series dual-sided dispensers

counter cut-out

Min.

33"

(839mm)

flat

surface

Shaded area is additional cutout required for

slide-in installations only

30.375"

(772mm)

38.5"

(978mm)

Plan view

U300 series single-sided dispensers

counter cut-out

All U300/UD300 dispensers must be installed level in both directions to ensure

proper operation and must be supported from below with supplied 6" (153mm) leg

accessory, or with channels installed at site. Do not hang dispenser on flange. These

dispensers weigh approximately 325 lbs (147kg). Use care when maneuvering unit

into position.

Dual-sided dispensers cannot be slid into counter unless

raised above counter. Call factory for details.

U300/UD300 series dispensers weigh approximately 325 lbs (147kg). Use of a

mechanical lifting device to lower dispenser into counter on drop-in installations is

strongly suggested to avoid injury.

DISPENSER MUST BE SUPPORTED SECURELY FROM BELOW. DO NOT HANG

DISPENSER ON COUNTER FLANGE.

DO NOT REDUCE DRAIN LINE SIZE. DO NOT TIE DRAINS TOGETHER.

PVC PIPE IS SUGGESTED. CARE MUST BE TAKEN IN SWEATING ANY ADJACENT

METAL DRAIN PIPE USED. EXCESSIVE HEAT APPLIED WHILE SWEATING METAL

PIPE MAY MELT PLASTIC FITTING ON DISPENSER.

Installing remote icemaker(s) (automatic load models only)

1. Position icemaker in desired location.

2. If ice transport tube will enter on tower side of dispenser, go to Step 5.

3. If ice transport tube will enter on side opposite tower, slide free end of ice transport tube(s) (without locator)

from inside of bin out through any of four prepared entry holes provided in dispenser sides, as shown.

4Mate ice tube locator with appropriate slot in ice tube bracket and secure with two (2) thumbscrews provided.

5. Proceed with ice transport tube installation from dispenser to icemaker(s) in compliance with instructions

contained in Icemaker Installation Manual packed with icemaker.

ice tube

entry

ice tube

entry

auger

tube

drive shaft

dispense

chute

Side view

Ice tube bracket

25 mm

Front view

Ice tube locator

ice tube bracket

locator tabs

inserted in

ice tube

holes

Correct installation of remote icemaker(s) is critical to proper performance of

icemaker and dispenser. Refer to installation manual packed with icemaker for

important details on ice transport tube run, ventilation requirements for air-cooled

remote icemakers and other installation requirements. Failure to comply with

instructions will void warranty.

Tower

side

Otros manuales para U300 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de hielo de Follett

Follett

Follett HCD Manual de operación

Follett

Follett Horizon Elite 710 Series Manual de usuario

Follett

Follett C33984 Manual de operación

Follett

Follett Horizon HME14000ABT Manual de usuario

Follett

Follett T400A Guía de configuración

Follett

Follett MC825 Series Guía de configuración

Follett

Follett MC 414A Series Manual de usuario

Follett

Follett Horizon Elite Harmony HCD E 710AHT Series Manual de usuario

Follett

Follett Horizon HME1000ABT Manual de usuario

Follett

Follett Horizon Elite HC Series Manual de operación

Follett

Follett Horizon Elite HCF1010R/N Manual de usuario

Follett

Follett Horizon Elite 1400 Series Manual de operación

Follett

Follett Horizon HCC1000ABT Manual de usuario

Follett

Follett HCD700R Manual de operación

Follett

Follett Horizon Chewblet 1810 Series Manual de usuario

Follett

Follett Horizon Elite HCD710A Manual de operación

Follett

Follett HCD710ABS Manual de usuario

Follett

Follett Maestro Plus MCD425A BS Manual de usuario

Follett

Follett HCD1400N Manual de operación

Follett

Follett Horizon Elite HCD1010RHT Manual de usuario

Follett

Follett Horizon Elite 1810 Series Manual de usuario

Follett

Follett Horizon Elite series Manual de usuario

Follett

Follett Maestro Plus MCD425WBS Manual de usuario

Follett

Follett R5A Manual de operación

Manuales populares de Máquina de hielo de otras marcas

Hoshizaki

Hoshizaki KMD-460MWJ Manual de usuario

Sub-Zero

Sub-Zero 315I Instrucciones de uso

Unold

Unold 48945 Manual de usuario

Kenmore

Kenmore 2217402A Manual de usuario

Cornelius

Cornelius WM600 Instrucciones de funcionamiento

GE XPIO43SCSS Manual de usuario

Hoshizaki

Hoshizaki KMD-901MAH Manual de usuario

Whynter

Whynter FIM-450HA Manual de usuario

U-Line

U-Line UMCR014-SC01A Manual de instalación

Andrew James

Andrew James AJ000522 Manual de usuario

Scotsman

Scotsman CME1356 Manual de usuario

Scotsman

Scotsman ACM 25 Manual de usuario

Kärcher

Kärcher IP 120 Manual de usuario

U-Line

U-Line SS1095 Manual de usuario

Maytag

Maytag MIM1554WRS - Ice Maker Manual de usuario

Hoshizaki

Hoshizaki KM-630MAH Manual de usuario

Princess

Princess Yonanas Manual de usuario

Unold

Unold 48946 Manual de usuario