Focusrite iTrack One Pre Manual de usuario
User Guide
POWER
www.focusrite.com
Version 1.0
2
OVERVIEW..................................................................... 3
Introduction .................................................................3
Product Compatibility .........................................................3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Box Contents ................................................................4
HARDWARE FEATURES.......................................................... 5
Top View ....................................................................5
Front View...................................................................6
Rear View ...................................................................6
USING THE iTrack One Pre ....................................................... 7
Power considerations .........................................................7
Audio setup in your app........................................................8
Recording from a microphone and/or instrument ..................................9
Using iTrack One Pre with GarageBand .........................................11
PERFORMANCE SPECIFICATIONS ................................................14
PHYSICAL AND ELECTRICAL CHARACTERISTICS ...................................14
TROUBLESHOOTING ...........................................................15
COPYRIGHT AND LEGAL NOTICES ...............................................15
TABLE OF CONTENTS
3
OVERVIEW
Introduction
Thank you for downloading this User Guide for the iTrack One Pre; we presume you have just become
the proud owner of one. The iTrack One Pre is the most compact Focusrite interface ever. Now
you can record on your iPhone® or iPad® from a microphone or instrument - anywhere, anytime
- at up to 96 kHz sample rate and 24-bit resolution, with all of Focusrite’s famed audio quality.
The iTrack One Pre is compatible with GarageBand, Cubasis and most other iPhone/iPad recording
apps, and lets you expand your creativity by adding vocals and ‘real-world’ instruments to the
software instruments provided by the apps.
This Guide provides an explanation of the iTrack One Pre to help you on your way. Even if
you’re not new to digital recording, please take the time to read through it so that you
are aware of all its possibilities. If you can’t find the information you need here, consult
http://www.focusrite.com/answerbase, which contains a comprehensive collection of solutions to
common technical support queries.
Product Compatibility
The iTrack One Pre is compatible with all models of Apple® iPhone or iPad fitted with a Lightning
connector. At the present time, these are as follows:
• iPhone SE
• iPhone 6s
• iPhone 6s Plus
• iPhone 6 Plus
• iPhone 6
• iPhone 5s
• iPhone 5c
• iPhone 5
• iPad Pro (12.9 inch)
• iPad Pro (9.7 inch)
• iPad Air 2
• iPad Air
• iPad mini 4
• iPad mini 3
• iPad mini 2
• iPad mini
• iPad (4th generation)
• iPod touch (6th generation)
• iPod touch (5th generation)
4
Features
The iTrack One Pre lets you connect a microphone or musical instrument to your iPhone or iPad
(your “iOS device”), and is powered from the iOS device. The signal at the input socket is routed to the
audio recording app on your iOS device via its Lightning connector. You can monitor your recording by
plugging headphones into your device in the usual way.
The iTrack One Pre uses a renowned Focusrite analogue mic pre-amp design: as well as having
great sound quality this can provide 48 V phantom power, so you can use a studio quality condenser
microphone if you have one. The “Combo” input socket also allows direct connection of an electric
guitar or bass - including those with high-output pickups.
With just one gain control, one switch and two LEDs, the iTrack One Pre has been designed to be as
easy to use as possible. Connect it to your iOS device using the Lightning cable supplied, plug your
mic or instrument into the input, set the gain and start recording – that’s really all there is to it.
Note that your iTrack One Pre’s base features a special material using microsuction technology. This
sticks to a flat smooth surface such as a desk top, which means it doesn’t move about while you’re
recording. If this should become less sticky over time because of accumulated dirt or fluff, it can be
cleaned with a damp cloth.
Box Contents
Along with the iTrack One Pre itself you should have:
• Getting Started booklet
• Micro USB-to-Lightning cable (red)
• Micro USB-to-USB ‘A’-type cable (black, for connecting an external power supply)
• Protective bag
5
HARDWARE FEATURES
Top View
ON 48V
GAIN
1
4
5
2 3
1. ON – once you’ve connected the iTrack One Pre to your iOS device, open the recording app you’re
going to use: after a few seconds this green LED will light, confirming that communication
has been correctly established.
2. GAIN – adjust the recording level so that the LED halo [3] does not turn red.
3. Gain “halo” LED – this is integral to the GAIN knob; this illuminates green to indicate “signal
present” and turns red if the level reaches 0 dBFS, indicating clipping. Once clip level is
reached, the halo stays red for one second, so you will know that the level was too high even
if it was only for a very short peak.
4. Phantom power switch – this is a latching switch and should be set ON if you are using a
microphone which requires 48 V phantom power (condenser or active ribbon types).
5. 48V – this LED will light green when the phantom power is turned on and the microphone
is operating normally. If the LED turns red, it indicates that the iTrack One Pre has entered
“current limiting mode”, which means the phantom power voltage supplied to the microphone
has been reduced. In this case the mic may not work properly, and you should power the
iTrack One Pre from an external USB PSU. See “Power considerations” on page 7 for
more details.
6
Front View
6
6. INPUT – a “Combo XLR” input socket. Connect a microphone via an XLR plug, or an instrument
via a ¼” TS (unbalanced) jack. Note that this socket will not work with a balanced source via
a ¼” TRS jack.
Rear View
POWER
7
8
7. Device connection – a USB Micro B socket for connecting to your iOS device. Plug the red
cable supplied with the iTrack One Pre in here; the other end of this cable has a Lightning
connector to plug into your compatible iPhone or iPad.
8. POWER – this USB Micro B socket lets you power your iTrack One Pre from a household USB
adaptor (e.g., an iPhone charger). Plug the black cable supplied with your iTrack One Pre in
here; the other end of this cable has a standard USB ‘A’ type plug. You should use external
power if the 48V LED [5] lights red when you are using a condenser mic, or if your iOS device
is low on battery (but note the device will NOT be recharged using this method).
7
USING THE ITRACK ONE PRE
Power considerations
The iTrack One Pre requires no batteries or separate power supply (but read on!).
When in use, it is powered from the iOS device to which is connected. Because the iTrack One Pre is
an active device, the battery in your iOS device will run down at a faster rate than it does in the device
alone, but this shouldn’t cause you any problems; it is simply good practice to make sure that there
is plenty of battery life in the device before you start recording.
The iTrack One Pre can also supply 48 V phantom power to a condenser (capacitor) microphone.
A condenser microphone consumes power itself, so remember that using one will further affect
the rate at which your battery runs down. Many modern condenser mics will work straightaway,
but some older or professional studio mics may require more current than the iTrack One Pre can
supply from your iOS device. You will know if this is the case because the 48V status LED will turn
from green to red. If this happens, you can power the iTrack One Pre from a standard household USB
power adaptor (e.g., an iPhone charger) using the USB cable supplied.
NOTE: Using an external USB PSU to power the iTrack One Pre does NOT charge the battery in your
iOS device.
To summarise:
• Your iTrack One Pre will normally be powered by your iPhone or iPad
• Use an external USB power supply only if:
• The 48V LED turns red when you connect a condenser mic, or
• Your iPhone or iPad has low battery life
POWER
Powering the iTrack One Pre from an iOS device.
Use the red Lightning
cable to connect devices.
8
POWER
Audio setup in your app
The iTrack One Pre is currently compatible with all Core Audio iPad apps, including the following:
• Impact by Focusrite (our own recording app)
• Garageband
• Cubasis
• Auria
Whichever recording app you’re using, its input signals – the signals you’re recording – will be derived
from the iTrack One Pre once your iOS device is correctly connected. With most apps this is entirely
automatic, and unlike computer-based DAW applications, no set-up procedure is necessary. If it
appears that your recording app does not automatically select the iTrack One Pre as its input source,
please consult the app’s Help files to check how to select it manually.
Black power cable with
USB power supply.
Using an external PSU with the iTrack One Pre to enable a
studio quality condenser mic to be used.
9
Recording from a microphone and/or instrument
Connect the iTrack One Pre to your iOS device using the red Lightning cable supplied. Open the
recording app on the device; the green ON LED will light after a few seconds, confirming that the two
devices are communicating correctly.
POWER
Now connect your audio source. The “Combi” type INPUT socket accepts signals from microphones
or instruments – e.g., guitars or bass guitars.
NOTE: Certain electronic instruments, e.g., keyboards and drum machines may also work
satisfactorily with the iTrack One Pre, though no guarantee can be given for any particular
instrument. Also, bear in mind that the iTrack One Pre is a mono device, and you may need to
take this into account when programming the instrument.
Mics connect via a 3-pin XLR plug; you will probably have one on the end of your microphone cable.
If the microphone needs phantom power to operate (i.e., it is a condenser or active ribbon mic),
switch the phantom power on AFTER plugging the mic in. If all is well, the 48V LED will light green.
If it lights red, the iTrack One Pre is in current limiting mode and the phantom power voltage will
be reduced. If this happens, connect the iTrack One Pre to an external USB power supply using the
black USB cable supplied.
10
Instruments use a ¼” (6.35 mm) TS (2-pole) jack plug. Do not use TRS (3-pole) jacks with the iTrack
One Pre.
1/4” TRS (3-pole) jack plug 1/4” TS (2-pole) jack plug 3-pin XLR plug (male)
Note that inserting an XLR plug into the INPUT socket will configure the iTrack One Pre as a mic
pre-amp, with the higher gain that microphones require: if you connect a higher level signal using an
XLR plug, you could easily end up with distortion!
The GAIN control has an integral “halo” LED to indicate signal level. Turn the GAIN control clockwise
while using the mic or instrument until it turns green. The halo should remain green most of the
time while you are playing or singing, but it’s OK if it goes off in the ‘gaps’. If it turns red you have the
gain set too high, and it should be turned down a bit. The best way to test that your gain level is not
too high is to play at the loudest you think you’ll be while recording, and ensure that the gain halo
does not turn red.
Your recording app will let you monitor what you’re recording via a pair of headphones connected
to your iOS device’s headphone output. When you plug the headphones in, the iPad or iPhone will
usually reconfigure its audio setup as it disables the internal speaker. The green ON LED on the
iTrack One Pre may go out momentarily – this is normal. You will probably see a message like this:
Screenshot taken from Garageband.
Tabla de contenidos
Otros manuales de Amplificador de Focusrite
Focusrite
Focusrite Clarett+ OctoPre Manual de usuario
Focusrite
Focusrite ToneFactory Manual de usuario
Focusrite
Focusrite OctoPre MkII Dynamic Manual de usuario
Focusrite
Focusrite RedNet MP8R Manual de usuario
Focusrite
Focusrite ISA TWO Manual de usuario
Focusrite
Focusrite ISA TWO Manual de usuario
Focusrite
Focusrite ISA One Manual de usuario
Focusrite
Focusrite Scarlett OctoPre Dynamic Manual de usuario
Focusrite
Focusrite ISA 220 Session Pack Manual de usuario
Focusrite
Focusrite Clarett+ 4Pre Manual de usuario
Focusrite
Focusrite VoiceMaster Pro Manual de usuario
Focusrite
Focusrite RedNet 4 Manual de usuario
Focusrite
Focusrite AMS-ISA-2 Manual de usuario
Focusrite
Focusrite OctoPre MkII Manual de usuario
Focusrite
Focusrite Clarett 8PreX Manual de usuario
Focusrite
Focusrite Red Series Manual de usuario
Focusrite
Focusrite TrakMaster Pro Manual de usuario
Focusrite
Focusrite VoiceMaster Manual de usuario
Focusrite
Focusrite ISA One Manual de usuario
Focusrite
Focusrite ISA One Manual de usuario
