Fly Sky FS-G7P Manual de usuario
FS-G7P
User Manual
Automatic Frequency Hopping Digital System
Copyright ©2022 Flysky Technology Co., Ltd.
Website
Thank you for purchasing our products.
Read the manual carefully to ensure your personal safety as well as the
safety of your equipment.
If you encounter any problems during using, please refer to this manual
first. If the problem is still not resolved, please contact the local dealer
directly or contact the customer service staff via the website below:
http://www.flysky-cn.com
Contents
1.Safety ..................................................................................................................1
1.1 Safety Symbols ......................................................................................................................1
1.2 Safety Guide ...........................................................................................................................1
2.Product Introduction......................................................................................... 2
2.1 Transmitter Overview .......................................................................................................................2
2.2 Receiver Overview.............................................................................................................................3
2.2.1 Status LED.........................................................................................................................................3
2.2.2 Interface ............................................................................................................................................3
2.3 Antenna.................................................................................................................................................3
3. Preparation.............................................................................................................................................4
3.1 Installing Transmitter Battery ........................................................................................................4
3.2 Installing Receiver and Servo ........................................................................................................4
4. Operation guide ...................................................................................................................................5
4.1 Power-on...............................................................................................................................................5
4.2 Bind.........................................................................................................................................................5
4.3 Setting Transmitter LED and Audio.............................................................................................5
4.4 Calibration............................................................................................................................................6
4.5 Restoring Factory Settings .............................................................................................................6
4.6 Power-off ..............................................................................................................................................6
5. System Interface................................................................................................ 7
6. Function Menu................................................................................................... 8
6.1 Settings-Channel Reverse...............................................................................................................9
6.2 Settings-Servo Travel........................................................................................................................9
6.3 Settings-Neutral Trim.................................................................................................................... 10
6.4 Settings-Dual Rate ......................................................................................................................... 10
6.5 Settings-Curve................................................................................................................................. 11
6.6 Settings-Smart Vehicle Control (SVC) ..................................................................................... 11
6.7 Settings-Beginner Mode.............................................................................................................. 11
6.8 Settings-ABS..................................................................................................................................... 12
6.9 Settings-IDLE UP............................................................................................................................. 13
6.10 Settings-ENG CUT........................................................................................................................ 13
6.11 Settings-CH SPEED ...................................................................................................................... 14
6.12 Auxiliary Channels-CH3 to CH7 ............................................................................................. 14
6.13 Mixes ................................................................................................................................................ 15
6.14 Mixes - Steering Mixes............................................................................................................... 15
6.15 Mixing-Programming Mixes..................................................................................................... 15
6.16 Timer................................................................................................................................................. 16
6.17 Timer – Timer................................................................................................................................. 16
6.18 Timer-Lap List ................................................................................................................................ 16
6.19 Switch Assignment ...................................................................................................................... 16
6.20 Receiver Settings .......................................................................................................................... 17
6.21 Receiver Settings-Failsafe.......................................................................................................... 17
6.22 Receiver Settings - Bind Settings............................................................................................ 18
6.23 Receiver Settings - Range Test ................................................................................................ 19
6.24 Receiver Settings - Sensor ........................................................................................................ 19
6.25 Receiver Settings - ESC Settings............................................................................................. 19
6.26 Receiver Settings -i-BUS Settings FS-CEV04 ...................................................................... 20
6.27 Model ............................................................................................................................................... 20
6.28 System Settings ............................................................................................................................ 21
6.29 System Settings - System Settings......................................................................................... 21
6.30 System Settings - Stick Calibration ........................................................................................ 22
6.31 System Settings - Firmware Update ...................................................................................... 22
6.32 System Settings - Factory Reset.............................................................................................. 23
6.33 System Settings - Help Center................................................................................................. 23
6.34 System Settings - About............................................................................................................ 23
7.FS-R7P Function Instructions.......................................................................24
7.1 Attentions.......................................................................................................................................... 24
7.2 Binding ............................................................................................................................................... 24
7.3 Firmware Update ............................................................................................................................ 24
7.4 Failsafe................................................................................................................................................ 25
8. Product Specifications...................................................................................26
8.1 Transmitter Specification FS-G7P.............................................................................................. 26
8.2 Receiver Specication FS-R7P.......................................................................................................................................27
9. Packing List........................................................................................................28
10. Certification ....................................................................................................29
10.1 DoC Declaration .................................................................................................................29
10.2 CE Warning .........................................................................................................................29
10.3 FCC Statement ..............................................................................................29
11. Environmentally Friendly Disposal .........................................................30
Website
1
• Misuse of this product may lead to serious injury or death. To ensure the safety of you
and your equipment, read this manual and follow the instructions.
• Make sure the product is properly installed in your model. Failure to do so may result in
serious injury.
• Make sure to disconnect the receiver battery before turning o the transmitter. Failure
to do so may lead to unintended operation and cause an accident.
• Ensurethatallmotorsoperateinthecorrectdirection.Ifnot,adjustthedirection
first.
• Makesurethemodelstayswithinthesystemsmaximumrangetopreventlossof
control.
• Do not use the product at night or in bad weather like rain or thunderstorm. It can
cause erratic operation or loss of control.
• Do not use the product when visibility is limited.
• Do not use the product on rain or snow days. Any exposure to moisture (water or snow)
may cause erratic operation or loss of control.
• Interference may cause loss of control. To ensure the safety of you and others, do not
operate in the following places:
• Near any site where other radio control activity may occur
• Near power lines or communication broadcasting antennas
• Near people or roads
• On any body of water when passenger boats are present
• Do not use this product when you are tired, uncomfortable, or under the inuence of
alcohol or drugs. Doing so may cause serious injury to yourself or others.
• The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a
large object can block the RF signal and lead to loss of control.
• Do not touch any part of the model that may generate heat during operation, or
immediately after use. The engine, motor or speed control, may be very hot and can
cause serious burns.
Prohibited Mandatory
1.Safety
1.1 Safety Symbols
Pay close attention to the following symbols and their meanings. Failure to follow these warnings could cause damage,
injury or death.
1.2SafetyGuide
Warning • Not following these instructions may lead to major injuries.
Danger • Not following these instructions may lead to serious injuries or death.
Attention • Not following these instructions may lead to minor injuries.
FS-G7P
Digital Proportional Radio Control System
Website
2
2.Product Introduction
This product uses the 2.4 GHz ANT(Ant protocol) enhanced automatic frequency hopping digital system, consisting
of FS-G7P transmitter and FS-R7P receiver. It has an output of 7 channels, compatible with model cars, boats, etc.
2.1 Transmitter Overview
Firmware upgrade, USB emulator,
and system power supply
Fixed port for the holder
of a mobile phone
for power supply
through 2s lithium
battery
[1]
[6]
[7]
[2] [3] [4]
[5]
[17]
[15]
[16]
Display
SW1 Key VR1 Knob
Ambient LED
Five-way switch, and keys for
menu navigation operations
RETNEthgiR
KCABtfeL
toggle switch
[11]
[12]
[8]
[9]
[10]
Power supply switch
[13]
[14]
compatible with the plac
ement
of lithium batteries.
JST interface:
For power supply
through 2S lithium
battery.
Website
3
2.2 Receiver Overview
2.2.1 Status LED
The status LED indicates the power supply state of the receiver and its working state.
O: The receiver is not powered on.
Light on in red: The receiver is connected to the power supply. It works normally.
Fast ashing: The receiver is in the bind mode.
Slow ashing: The LED ashes slowly when the receiver is powered o, unbound, or no signal.
2.2.2 Interface
All the interfaces are 2.54 mm standard pins for connecting the receiver to each terminal part of the model. Please
follow the direction according to the label see the label direction on the side of the receiver.
2.3 Antenna
Note
• To ensure the signal quality, the transmitter and receiver antennas should be kept
vertical to the ground as much as possible. In operations, please adjust the transmitter
angle. Make the antenna towards the direction of the model receiver. Keep the receiver
antenna extending out of the model and perpendicular to the ground.
Caution
• It is strictly prohibited to hold the antenna of the transmitter and the antenna of the
receiver in operations. Otherwise, the quality and strength of the radio transmission
signal will be greatly reduced, resulting in the failure and out of control of the model.
Note
• Do not pull the antenna of the receiver. Do not tie the antenna and the servo cable
together. Do not put the antenna close to the metal materials, because this will aect
the signal strength of the receiver.
It should be noted that this is a transmitter with a built-in antenna. Please use the transmitter correctly.
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8][9][10]
[11]
[12] [13] [14]
[16]
[17]
[15]
[1] CH1/P(PWM/PPM)
[2]-[5] CH2- CH5
[6] BIND interface
[7] BVD/VCC(Battery voltage detection/Power supply interface)
[8] CH7
[9] SERVO
[10] LED
[11] Antenna
[12] BIND button
[13] SENS interface
[14] CH6
[15] Signal pin
[16] + (Power anode)
[17] - (Power cathode)
FS-G7P
Digital Proportional Radio Control System
Website
4
Danger • Do not use the battery if damaged.
Battery type: AA batteries or 2S lithium batteries JST interface inside the battery compartment.
Please follow the steps below to install the transmitter batteries：
1. Open the battery compartment cover.
2. Put 4 AA batteries with sucient electricity into the battery compartment. Ensure that the metal terminals on the
batteries contact the metal terminals inside the battery compartment.You should choose the proper size of 2S 7.4V
lithium battery to access the JST interface. Connect them correctly.
3. Cover the battery compartment.
3.2 Installing Receiver and Servo
Install the receiver and servo in the following methods:
3. Preparation
Prior to operations, please install the battery and connect devices according to the sequence and guide as
described in this chapter.
3.1 Installing Transmitter Battery
Danger • Do not open, disassemble, or attempt to repair the battery.
Danger • Only use specied battery (X4 AA batteries).
Danger • Do not crush/puncture the battery, or short the external contacts.
Danger • Do not drop the battery or expose to strong shocks or vibrations.
Danger • Do not expose to excessive heat or liquids
Danger • Always store the battery in a cool, dry place.
Steering servo
Throttle servo
AUX. servo
AUX. servo
AUX. servo
AUX. servo
AUX. servo
CH1
CH3
CH2
CH4
CH5
CH7
CH6
Website
5
4. Operation guide
After the preparation is completed, you can start to use the product according to the guide in this chapter.
4.1 Power-on
Power on the product according to the following steps:
1. Check the system status to make sure the battery is fully charged and properly installed.
2. Turn the switch to the [On] position. The screen will light up.
3. Power on the receiver.
Warning • At this point, the system starts. Please operate carefully. Otherwise, it may cause
damage to the product or injury to people.
Warning • For your safety, please turn the transmitter switch and throttle to the safe position.
4.2 Bind
The ex-factory bind settings of the transmitter and receiver are completed successfully. If you need to replace the
transmitter or receiver with another one, please follow the steps below for binding. The receiver supports TWO WAY
binding and ONE WAY binding. The transmitter will display the information returned from the receiver after theTWO
WAY binding is nished. And the default is ONE WAY binding, the steps are as below:
1. Power on the transmitter, then select RX SET > BIND SET > STRAT to put the transmitter into bind state.
2. Connect the power cable to the BVD/VCC interface on the receiver. At this time, the receiver LED ashes slowly.
3. Press and hold the BIND button on the receiver for more than 3 seconds or press and hold the BIND key on the
receiver for power-on.
4. After the receiver LED becomes slow ashing, then manually put the transmitter to exit the binding state. At this
time, the receiver LED is solid on indicating the binding is successful.
5. Verify that the transmitter and receiver are working properly. If you need to re-bind, repeat the above steps.
4.3 Setting Transmitter LED , Sound and Volume
This LED is a monochromatic light. You can set the ON and OFF state. You can enable or disable the sound for the
• The procedure is applicable to the bind between only FS-G7P transmitter and FS-R7P receiver. The bind
methods vary with receivers. For details about the operations, you can visit the FLYSKY ocial website to
obtain the receiver manual or other related information.
• Since the product is constantly updated, please visit the FLYSKY ocial website to obtain the latest
transmitter and receiver compatibility list.
This product system is compatible with most of our ANT Protocol receiver models. The details are as follows:
RF standard: 2.4 GHz Ant protocol
Receiver model: FS-R7P
Note:If TWO WAY mode is selected at the transmitter side, when the receiver LED status changes from fast-ashing to
solid-on, the binding is successful.
FS-G7P
Digital Proportional Radio Control System
Website
6
4.4 Calibration
The calibration is required in case of data oset of the transmitter due to physical wear in long-term operations. At this
time, we need to calibrate the output data and neutral angle of the traversing steeringwheel, throttle trigger, VR1and
VR2.
The transmitter has been calibrated at the factory. If you need to recalibrate it, please follow the steps below: Please
follow the steps below to perform the settings:
1. Power on the transmitter, enter the system menu, and select the stick calibration function. Follow the prompts to
press the Start key for calibration.
2. Swing the steeringwheel and trigger to the maximum and minimum travel in each direction respectively and then
release them. Turn VR1 to its maximum and minimum travel and then back to the neutral position. Toggle the VR2
left and right repeatedly to the maximum extent for two or three times. Finally, toggle the VR2 back to the neutral
position.
3. Press the return key to exit the calibration interface. The calibration is complete. If the pop-up window indicates
that the calibration has failed, it means that the control to be calibrated has not reached the maximum and
minimum travel, or VR1 and VR2 has not been toggled to the middle position. The re-calibration is required.
4.5 Restoring Factory Settings
When you want to clear the data in the transmitter, you can restore all data in the transmitter to default values. That is,
all model data and settings are restored to the default state.
Please follow the steps below to restore factory settings:
1. Power on the transmitter, enter the system menu, and select the factory reset function. Follow the prompts to
press the OK button to start the reset.
2. After the successful reset, the system automatically returns and stays in the system menu interface. It indicates that
the system has been restored to the factory settings.
4.6 Power-o
Please follow the steps below to power o the system:
1. Power o the receiver.
2. Turn the switch to the OFF position to turn o the transmitter.
Caution • When you shut down the system, make sure to power off the receiver, and then the
transmitter. Otherwise, the model may be damaged and people may be injured.
system operations and alarms. For system operations and alarms, you can enable/disable the sound separately or
collectively. In addition, you can set the sound volume separately.
Please follow the steps below to perform the settings:
1. Start the transmitter and enter the SYSTEM menu. In the SYSTEM settings, set the LED, SOUND, and VOLUME.
2. After the settings are completed, return back.
Otros manuales para FS-G7P
2
Tabla de contenidos
Otros manuales de Mando a distancia de Fly Sky
Fly Sky
Fly Sky VK-R4A Manual de usuario
Fly Sky
Fly Sky FS-VK-G4P Manual de usuario
Fly Sky
Fly Sky FS-lT4S Manual de usuario
Fly Sky
Fly Sky Nirvana NV14 Manual de usuario
Fly Sky
Fly Sky SM001 Manual de usuario
Fly Sky
Fly Sky FS-T6 Manual de usuario
Fly Sky
Fly Sky FS-HW-G4P Manual de usuario
Fly Sky
Fly Sky FS-G7P Manual de usuario
Fly Sky
Fly Sky FS-GT2B Manual de usuario
Fly Sky
Fly Sky FS-TH9X Manual de usuario
Fly Sky
Fly Sky FS-i6 Manual de usuario
Fly Sky
Fly Sky Noble NB4 Manual de usuario
Fly Sky
Fly Sky FS-i6S Manual de usuario
Fly Sky
Fly Sky FS-I4 Manual de usuario
Fly Sky
Fly Sky FS-i6 Manual de usuario
Fly Sky
Fly Sky FS-i10 Manual de usuario
Fly Sky
Fly Sky FS-CT6A Manual de usuario
Fly Sky
Fly Sky FS-MG7 Manual de usuario
Fly Sky
Fly Sky Noble NB4 Manual de usuario
Fly Sky
Fly Sky FS-i6S Manual de usuario
