Fluke MicroNetBlink Kit Manual de usuario
MICROTOOLS
MICRONETBLINK™KIT
MicroNetBlinkTM
MicroProbeTM
UserGuide
ManuelUtilisateur
BenutzerHandbuch
Manualeper l'utente
Guía del Usuario
Manual do Utilizador
2947-4511-01 Rev. 01 11/2001
© 2001 Fluke Networks, Inc. All rights reserved. Printed in USA.
All product names are trademaaarks of their respective companies.
ENGLISH - 1
Congratulations on your purchase of
MICRONETBLINK
and/or
MICROPROBE!
The MICRONETBLINK is a practical network installa-
tionandtroubleshootingtoolthatflashesahublight,
features a unique tone signal, two test leads, 8-
conductor twisted pair cable (RJ45), and a 4-con-
ductor modular cable (RJ11) to test standard Cat 5
cabling, COAX cables, and bare wires.
MICRONETBLINK also does continuity tests and
checks tip/ring telephone signals. The signal emit-
ted by the MICRONETBLINK can be easily traced by
the MICROPROBE, even when cables are in a bundle
or hidden in walls or ceilings. Use MICRONETBLINK
and MICROPROBE to locate hub ports, verify cable
continuity, determine line polarity and voltage in
localnetwork twisted pair cabling andmodular tele-
phone lines. The MICROPROBE is equipped with a
tone amplifier and an LED indicator that detects
audible frequency tones for accurate tracing and
identification of wires.
Contents
MicroNetBlinkFeatures: ............................................. 3
MicroProbeFeatures .................................................. 3
Battery ........................................................................ 4
High Voltage Protection .............................................. 4
MicroNetBlink Tests .................................................... 5
Flashing the Hub Light Status .................................... 5
Sending a Tone .......................................................... 5
IdentifyingTelephone Line Polarity ............................. 6
Verifying Telephone Lines........................................... 6
Testing for Low Voltage .............................................. 7
TestingContinuity ....................................................... 7
Testing Continuity using Tone ..................................... 8
Coax Testing .............................................................. 8
Appendix A ................................................................. 9
MicroNetBlinkTM / MicroProbeTM
MICRONETBLINK
& MICROPROBE
3-Postion Switch:
ContinuityTest
Off/ Volt Check
Signal
F-Type
Connector
for tone
tracing
Ring/Tip
Polarity
Test LED
LED
Netblink
LED
Low
Battery
LED
RJ11Connector for
Continuity Test and
Tip/Ring Signal.
Red and Black
Alligator clips for
Continuityand
Voltage Check.
RJ45 Connector for
flashing of Hublight
and Tone Tracing.
Netblink/
Tone
Button
Trace Button
Signal LED
Volume
Control
Inductive
Probe with
Non-
conductivetip
ENGLISH - 3
MICRONETBLINK
Features
• 2-position NetBlink/Tone button for flashing a hub light or
toning
• Toggle switch to control 3 modes of operation
• 2-color LED indicator for telephone line polarity, continuity
and voltage testing
• 8-pin modular cable (RJ45) for flashing hub lights, tracing
cables, and locating jacks
• Black and red alligator testing leads and standard 4-pin
modular cable for individual wire tests or modular jack
RJ11 tests
• Convenient compact size and simple application
• Low battery indicator
MICROPROBE
Features
• Special inductive plastic tip that prevents accidental shorts
(possible with copper-tip tracers)
• Traces and identifies wires or cables in a bundle or group
without damaging cable insulation
• Locates RJ45 jacks in wiring systems
• Adjustable volume level control and LED indicator for noisy
work environments
• Power switch prevents battery drain
• Works with all tone generators including
MICROSCANNER PRO, MICROMAPPER,
MICRONETBLINK
• Low battery indicator
MicroNetBlinkTM / MicroProbeTM
Battery
MICRONETBLINK requires a 9 Volt Alkaline battery.
MICROPROBE requires a 9 Volt Alkaline battery.
The low Battery LED will light up when a low
battery condition is detected.
Using the units with a low battery may effect the
test accuracy.
If the units are stored for more than one month,
the battery should be removed.
High Voltage Protection
Do not touch the tip of MICROPROBE to the active
circuit contact or line.
Remember to adjust the volume rotary to reach
an ideal volume level.
Do not expose the units to extreme humidity or
direct sunlight.
Do not open the units or attempt to repair in case
of malfunction. Please send it back to your
distributor for repair or replacement.
MICRONETBLINK is designed to withstand input
voltage conditions that arise from normal
telephony applications such as 48 VDC at less
than 80 ma or 24 VAC used to power many
keysets. Tests cannot be performed when hazard
conditions exist on the inputs.
ENGLISH - 5
MICRONETBLINK
Tests
Flashing the Hub Light Status
1. Set the toggle switch to the Signal position.
2. Plug the 8-position cable (RJ45) into the jack
to be tested.
3. Verify that the button on the face of the
MICRONETBLINK IS in the NETBLINK position.
4. In the wiring closet, view a light that blinks
once every 4 seconds at the port to which the
cable is connected.
MICRONETBLINK will blink the hub's status
indicator to assist locating a single channel in a
busy wiring closet.
Sending a Tone
1. Set the toggle switch to the Signal position.
2. Connect the black lead to ground and any
other cable (coax, RJ45, or red alligator) to
the cable to be traced.
3. Press the button to TONE position to
activate the toner.
4. Reception of the tone will be loudest (Speaker)
or brightest (LED) on the wire under test.
Caution: Do not connect to an active AC circuit
exceeding 24 V in this mode.
MicroNetBlinkTM / MicroProbeTM
Identifying Telephone Line Polarity
1. Set the toggle switch to the Off/Volt ü
position.
2. Connect the black alligator test lead to the TIP
(+) connection, usually green or blue.
3. Connect the red alligator test lead to the RING
(-) connection, usually red or marked R.
The LED indicator will light up:
GREEN indicates normal polarity
RED indicates reversed polarity
RED/GREEN indicates presence of AC power
on the telephone line
Verifying Telephone Lines
1. Set the toggle switch to the Off/Volt ü
position.
2. Insert the standard 4-pin modular cable into
the modular wall jack, or connect the red
alligator test lead to the RING (-) and the black
alligator test lead to the TIP (+).
The LED indicator will light up:
GREEN indicates a correct wired telephone
circuit that is on-hook
GREEN (DIM) indicates a correct wired
telephone circuit already in use or off-hook
RED indicates a reversed polarity phone circuit
3. Use a second phone line to dial the number
under test.
RED and GREEN (rapidly flashing) indicates a
ringing signal.
ENGLISH - 7
4. Set the toggle switch to Cont üto answer the
line or go off-hook.
Note: The brightness of the GREEN line status is
an indicator of the amount of telephone loop
current present while the toggle switch is in the
Cont
ü
position.
CAUTION: Telephone circuit voltages can be
hazardous, never touch the metal of the test
leads while the MicroNetBlink is attached to a
telephone line.
Testing for Low Voltage
CAUTION: MicroNetBlink is designed for
checking low voltage (less than 24 Volts DC or
AC only). Do not connect to any high voltage
circuits!
1. Set the toggle switch to the Off/Volt ü
position.
2. Connect the red alligator test lead to a wire of
the pair or circuit.
3. Connect the black alligator test lead to the
other wire of the pair or circuit.
If the LINE STATUS is GREEN, the black test
lead is connected to a NEGATIVE(-) DC Voltage
If the LINE STATUS is RED, the black test lead
is connected to a POSITIVE (+) Voltage
If the LINE STATUS is RED/GREEN, AC Voltage
is present.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Equipo de prueba de Fluke
Fluke
Fluke 6270A Manual de usuario
Fluke
Fluke 810 Manual de usuario
Fluke
Fluke LinkIQ Manual de usuario
Fluke
Fluke 368 FC Guía de referencia
Fluke
Fluke 975CK Manual de usuario
Fluke
Fluke 6003A Manual de usuario
Fluke
Fluke 5320A Manual de usuario
Fluke
Fluke FIBER QUICKMAP Manual de usuario
Fluke
Fluke LinkRunner AT 1000 Manual de usuario
Fluke
Fluke 9009 Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
Fluke
Fluke VisiFault Visual Fault Locator Manual de usuario
Fluke
Fluke ScopeMeter 190-104 Manual de instrucciones
Fluke
Fluke 1621 Manual de usuario
Fluke
Fluke 717-1000G Manual de instrucciones
Fluke
Fluke 718 Series Manual del propietario
Fluke
Fluke 975 AirMeter Instrucciones de instalación y funcionamiento
Fluke
Fluke DTX-MFM Manual de usuario
Fluke
Fluke 39 Manual de usuario
Fluke
Fluke 721 Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Mercury
Mercury TSL01 Manual de usuario
