Fluke 3014-PR Manual de usuario
PN 3039221
February 2008
©2008 Fluke Corporation. All rights reserved. Product specifications are
subject to change without notice. Printed in USA.
®
3014-PR
AC Current Clamp
Instruction Sheet
Introduction
The Fluke 3014-PR AC Current Clamp (the Clamp) is a compact
ac current clamp designed specifically for the Fluke 1750.
Designed to meet the most stringent demands in industry and
electrical contracting, it also meets the latest safety and
performance standards.
Symbols
The table below lists the symbols used on the Clamp and/or in
this instruction sheet.
Symbol Description
~Do not dispose of this product as unsorted municipal
waste. Go to Fluke’s website for recycling information.
WRisk of Danger. Important Information. See manual.
XHazardous Voltage. Risk of electric shock.
TDouble insulation.
,Application around and removal from HAZARDOUS
LIVE conductors is permissible.
@Underwriters Laboratories. Conforms to UL Canadian
and U.S. standards.
PComplies with the relevant European standards.
;Conforms to relevant Australian standards.
3014-PR English Instruction Sheet
Page 2
Safety Instructions
Please read this section carefully. It will familiarize you with the
most important safety instructions for handling the Clamp. In this
instruction sheet, a Warning identifies conditions and actions
that pose hazard(s) to the user. A Caution identifies conditions
and actions that may damage the test instruments.
WX Warning
The Clamp may only be used and handled by
qualified personnel. To avoid personal injury, follow
these precautions:
•To avoid electric shock, use caution during
installation; high voltages and currents may be
present in circuit under test.
•Do not use the Clamp if damaged. Always
connect to display device before it is installed
around the conductor.
•Use the Clamp only as specified in the
operating instructions; otherwise the safety
features may not protect you.
•Adhere to local and national safety codes.
Individual protective equipment must be used
to prevent the shock and arc blast injury where
hazardous live conductors are exposed.
•Before each use, inspect the Clamp. Look for
cracks or missing portions of the housing or
output cable insulation. Also look for loose or
weakened components.
•Use caution when working with voltages above
60 V dc, 30 V ac rms or 42 V ac peak. Such
voltages pose a shock hazard.
•Use of this equipment is designed to CAT III
standards. CAT III equipment is designed to
protect against the transients in the equipment
in fixed equipment installations, such as
distribution panels, feeders and short branch
circuits, and the lighting systems in large
buildings.
•Do not use the Clamp in wet environments or in
locations that hazardous gases exist.
•Do not hold the Current Clamp anywhere
beyond the tactile barrier, see Figure 1.
3014-PR English Instruction Sheet
Page 3
Tactile Barrier
ezk01.eps
Figure 1. 3014-PR AC Current Clamp
Operating Instructions
1. Connect the Clamp to the 1750 current input jack. Verify
that the 1750 has recognized that a current Clamp is
connected.
2. Place the Clamp around the conductor under test.
3. Observe and take measurements as required. Positive
output indicates that the current flow is in the direction
shown by the arrow on the Clamp.
Cleaning
Clean the Clamp periodically by wiping it with a damp cloth and
detergent. Do not use abrasive cleaners or solvents. Do not
immerse the Clamp in liquids.
Specifications
Electrical Specifications
Operating Range 40 A
Measurement Range 0.1 to 40 A
Transformation Ratio Voltage output
Output Signal 50 mV/A (2 V @ 40 A)
Range Accuracy Phase Shift
0.1 to 1 A ≤2 % of Reading ± 1 mV –
1 to 5 A ≤1 % of Reading ± 1 mV ≤3 °
5 to 40 A ≤1 % of Reading ± 1 mV ≤2 °
Reference conditions: 20 °C to 26 °C, 20 to 75 % RH, external magnetic
field <40 A/m, 48 to 65 Hz sine wave, distortion factor less than 1 %, no
dc component, no external current carrying conductor, test sample
centered. Load impedance 1 MΩ.
3014-PR English Instruction Sheet
Page 4
Overload 50 A for Continuous
Frequency Range 40 to 10 kHz (See Figure 2)
Crest Factor 3 @ 10 A rms with an error (due to CF) of
3 %
Working Voltage 600 V rms
Common Mode Voltage 30 V rms
Influence of Adjacent
Conductor
<15 mA/A at 50 Hz
Influence of dc on ac signal dc current <20 A, <5 %
Influence of Conductor
Position in Jaw
0.5 % of mV output @ 50/60 Hz
Influence of Frequency 40 Hz to 1 kHz: 0.5 % of mV output
1 kHz to 10 kHz: 2 % of mV output
Mechanical Specifications
Dimensions 5.47 x 2.00 x 1.18 in. (139 x 51 x 30 mm)
Weight 180 g (6.5 oz)
Jaw Opening 0.83 in. (21 mm)
Maximum Conductor Size
Cable
Bus Bar
0.78 in. (20 mm)
0.78 x 0.19 in. (20 x 5 mm)
Case Protection IP 40 (IEC 60529)
Drop Test 1.0 m six sides to oak floor
Vibration MIL-PRF-28800F
Polycarbonate Material
Jaws
Case
Polycarbonate Red UL 94 V0
Polycarbonate ABS Gray: UL 94 V0
Opening Operations - Life >50,000
Output
1 ft round 2 conductor cable w/4-pin Lemo
connector
3014-PR English Instruction Sheet
Page 5
Environmental Specifications
Operating Temperature 14 ° to 131 °F (-10 ° to +55 °C)
Storage Temperature -40 ° to 158 °F (-40 ° to +70 °C)
Altitude Non-operating: 0 to 12,000 m
Operating: 0 to 2000 m
Operating Relative
Humidity
10 to 35 °C 85 % RH
(without roll-off above 35 °C)
Influence of Temperature
≤150 ppm/°K, or 0.15 % of mV output per
10 °K
Influence of Humidity
(10 to 90% RH)
≤0.2 % of mV output per 10 °K @ 18 °C to
28 °C
Safety Specifications
Electrical
Conforms to EN/IEC 61010 and 61010-2-
032
600 V Cat. III, Pollution Degree 2
Electromagnetic
Compatibility
EN 50081-1 Class B
EN 50082-2 Electrostatic discharge; IEC
61000-4-2
Radiated field IEC 61000-4-3
Fast transients IEC 61000-4-4
Magnetic field at 50/60 Hz IEC 61000-4-8
3014-PR English Instruction Sheet
Page 6
2 A
40 A
-35.00
10.00
5.00
0.00
-5.00
-10.00
-15.00
-20.00
-25.00
15.00
20.00
1.00 10.00 100.00 1000.00 10000.00 100000.00
1.00 10.00 100.00 1000.00 10000.00 100000.00
-25.00
-15.00
- 5.00
-30.00
-20.00
-10.00
0.00
Error in % of measurementPhase in °
Frequency in Hz
Frequency in Hz
5.00
2 A
40 A
ezq001.eps
Figure 2. Frequency Response at 2 and 40 A
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship
for one year from the date of purchase. This warranty does not cover
fuses, disposable batteries, or damage from accident, neglect, misuse,
alteration, contamination, or abnormal conditions of operation or
handling. Resellers are not authorized to extend any other warranty on
Fluke’s behalf. To obtain service during the warranty period, contact your
nearest Fluke authorized service center to obtain return authorization
information, then send the product to that Service Center with a
description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some
states or countries do not allow the exclusion or limitation of an implied
warranty or of incidental or consequential damages, this limitation of
liability may not apply to you.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
Tabla de contenidos
Otros manuales de Instrumento de medición de Fluke
Fluke
Fluke 714 Manual de usuario
Fluke
Fluke 381 Manual de usuario
Fluke
Fluke ScopeMeter 190-102 Manual de usuario
Fluke
Fluke QA-ES III Manual de lista de piezas
Fluke
Fluke VIBGUARD compact Manual de usuario
Fluke
Fluke CO-205 Manual de usuario
Fluke
Fluke 481-DESI Manual de instrucciones
Fluke
Fluke 345 Manual de uso y cuidado
Fluke
Fluke 721A Manual de usuario
Fluke
Fluke i3000s Flex Series Manual de usuario
Fluke
Fluke 3210-PR Manual de usuario
Fluke
Fluke 1750/ET Manual de usuario
Fluke
Fluke SigmaPace 1000 Manual de usuario
Fluke
Fluke 922 Manual de usuario
Fluke
Fluke WaveRunner Manual de usuario
Fluke
Fluke FS17XX Manual de usuario
Fluke
Fluke 8050A Manual de usuario
Fluke
Fluke 845A Manual de usuario
Fluke
Fluke 433 Guía de configuración
Fluke
Fluke 411D Instrucciones de instalación y funcionamiento
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario