Fluidwell E Series Instrucciones de operación

FW_E110_AutoUnitConv_002_EN Page 1

E-SERIES

Flow rate indicator / Totalizer

E110-SERIES TUTORIAL

AUTOMATIC UNIT CONVERSION

NOTICE

This E110-series tutorial is meant as a step-by-step guidance on how to use and

set the automatic unit conversion. This tutorial is an addendum to the installation

manual that came with the E-series.

This E110-series tutorial assumes that the E-series is in a safe area.

E-series - Explosion proof indicators for hazardous areas.

More info: www.fluidwell.com/eseries

AUTOMATIC UNIT CONVERSION E110-SERIES TUTORIAL

Page 2 FW_E110_AutoUnitConv_002_EN

Disclaimer

This E110-series tutorial is created to provide as accurate and authoritative information

regarding the subjects covered as was available at the time of writing. The copyright owner

of this E110-series tutorial cannot take any responsibility or liability for any errors or

omissions in this E110-series tutorial or for discrepancies arising from the features of any

actual item in the respective refit being different from those shown in this E110-series

tutorial. The publisher and copyright owner shall not be liable under any circumstances, for

any consequential, special, contingent, or incidental damages or injury, financial or

otherwise, suffered by any part arising out of, connected with, or resulting from the use of

this E110-series tutorial or the information contained therein.

Nothing from this E110-series tutorial may be reproduced, or transmitted in any form or by

any means, electronic or mechanical, including photocopying, recording or any information

storage or retrieval system without prior written approval by Fluidwell BV.

Trademarks

All trademarks used in this E110-series tutorial are the property of their respective owners.

Document control

This E110-series tutorial is an addendum to the documentation set that came with the E-

series. It is the responsibility of the owner to keep the documentation set up-to-date.

We reserve the right to make changes of any kind without prior written notice. Please visit

our internet site for the latest information and (product) updates.

This E110-series tutorial is a translation of: FW_E110_AutoUnitConv_001_EN.

Revision history

VERSION

DESCRIPTION

DATE

001

Initial release

22 July 2015

002

K-Factor calculation revised

2 February 2016

E110-SERIES TUTORIAL AUTOMATIC UNIT CONVERSION

FW_E110_AutoUnitConv_002_EN Page 3

Table of content

1DESCRIPTION OF THE AUTOMATIC UNIT CONVERSION ................................................4

1.1 The relation between the K-Factor and the automatic unit conversion ...................................4

1.2 The relation between the K-Factor and the measurement unit set by hand............................4

2HOW TO SETUP THE AUTOMATIC UNIT CONVERSION...................................................5

2.1 How to set the K-Factor (units) for the flowmeter ...................................................................5

2.1.1 The automatic unit conversion - AUTO-VOL and AUTO MAS mode......................................................5

2.1.2 The automatic unit conversion - HAND mode.........................................................................................7

2.2 Set the reading for the (accumulated) total.............................................................................7

2.2.1 The (accumulated) total - AUTO-VOL and AUTO MAS mode................................................................7

2.2.2 The (accumulated) total - HAND mode ...................................................................................................9

2.3 Set the reading for the flow rate ...........................................................................................10

2.3.1 The flow rate - AUTO-VOL and AUTO MAS mode ...............................................................................10

2.3.2 The flow rate - HAND mode...................................................................................................................12

AUTOMATIC UNIT CONVERSION E110-SERIES TUTORIAL

Page 4 FW_E110_AutoUnitConv_002_EN

1 Description of the automatic unit conversion

The automatic unit conversion is a feature that helps you to avoid the different K-Factor

calculations for the (accumulated) total and the flowrate. With the automatic unit conversion,

you only need the test/calibration certificate that came with your flowmeter. On this

certificate you will find the (average) K-Factor and the related measurement unit. To use the

automatic unit conversion, you only need to enter the (average) K-Factor and the related

measurement unit from the flowmeter certificate.

You need to preset the type of measurement unit: volume, mass or hand. Hand is selected

for measurement units which are not supported by the automatic unit conversion.

1.1 The relation between the K-Factor and the automatic unit conversion

The K-Factor is a figure that represents the amount of pulses which relates to the quantity

of a material that passes the flowmeter.

There are three different K-Factors:

one for the flowmeter (as given on the certificate);

one for reading of the (accumulated) total:

one for the reading of the flowrate.

When another measurement unit is selected for the (accumulated) total or the flowrate, the

automatic unit conversion uses the K-Factor of the flowmeter to, calculate the correct

reading for the (accumulated) total and the flowrate separately.

NOTICE

When the E-series already shows a (accumulated) total and the measurement

unit is changed, the present total is not recalculated into the new measurement

unit. Therefore the total needs to be cleared before you enter a new measurement

unit.

1.2 The relation between the K-Factor and the measurement unit set by hand

The K-Factor is a figure that represents the amount of pulses which relates to the quantity

of a material that passes the flowmeter.

There are three different K-Factors:

one for the flowmeter (as given on the certificate);

one for reading of the (accumulated) total:

one for the reading of the flowrate.

For the correct reading, you need to know the K-Factor of the flowmeter and the

measurement unit for which the flowmeter is calibrated.

Example

For this example:

the flowmeter has a K-Factor: 6624.605 and a measurement unit: m3.

the measurement unit for (accumulated) total is required per US GAL.

the unit conversion: 1 m3equals 264.17 US GAL (1 US GAL equals 0.00378 m3).

The flowmeter generates 6624.605 pulses per m3. The selected unit for (accumulated) total

is US GAL. For the calculation of the K-Factor for the (accumulated) total: the K-Factor

6624.605 with an unit m3converted into US GAL gives 6624.605 : 264.17 = 25.077.

E110-SERIES TUTORIAL AUTOMATIC UNIT CONVERSION

FW_E110_AutoUnitConv_002_EN Page 5

2 How to setup the automatic unit conversion

This chapter explains the procedure how to setup the automatic unit conversion.

2.1 How to set the K-Factor (units) for the flowmeter

For easy access the procedure gives the action (what to do), the result (how the E-series

will respond) and a notice to give additional information to make the procedure more easy to

do. For future reference, make a note of the settings.

2.1.1 The automatic unit conversion - AUTO-VOL and AUTO MAS mode

This procedure gives the information how to setup the AUTO-VOL or the AUTO-MAS mode.

For volumetric units, use the AUTO-VOL mode. For mass units use, use the AUTO-MAS

mode.

NOTICE

This procedure assumes that the E-series is not installed in the field.

This procedure uses the factory default settings for the explanation. (AUTO-VOL

[automatic unit conversion], L/min [flow rate] and m3[Total, accumulated total]).

This procedure assumes, as read from the flowmeter certificate, the flowmeter is

calibrated for: 6624.605 [average K-factor], m3/hr [flow rate].

ACTION

RESULT

NOTICE

1. Press the PROG button

for at least 7 seconds.

The SETUP indicator

comes on continuously.

2. Wait for the setup menu

to show.

The setup menu shows.

3. Press the ► button until

the FLOWMETER

menu shows.

The FLOWMETER menu

shows.

In this menu you can match the

flowmeter with the E-series.

4. Press the ▲ button until

the UNITS menu

shows.

The UNITS menu shows.

The UNITS menu is used to make

a choice between the automatic

unit conversion modes.

5. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can select the automatic

unit conversion mode.

When the K-factor of the flowmeter

is known:

For volumetric measurement

select AUTO-VOL.

For mass measurements select

AUTO-MAS.

For measurement units which are

not supported by AUTO-VOL or

AUTO-MASS, select HAND.

6. Press the ▲ button to

make the required

selection.

The AUTO-VOL selection

shows (the flowmeter is

calibrated for m3/hr).

For the explanation,

the mode AUTO-VOL is selected.

7. Press the PROG button

momentarily.

The PROG indicator goes

off.

The selection is

confirmed.

8. Press the ▲ button until

the UNIT menu shows.

the UNIT menu shows.

9. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the measurement

unit.

AUTOMATIC UNIT CONVERSION E110-SERIES TUTORIAL

Page 6 FW_E110_AutoUnitConv_002_EN

ACTION

RESULT

NOTICE

10. Press the ▲ button to

make the required

selection.

The m3 selection shows

(the flowmeter is

calibrated for m3/hr).

Read the unit from the flowmeter

certificate and select the same

measurement unit in this menu.

NOTICE

If you cannot select the required measurement unit, you cannot use the automatic

unit conversion. Best practice is to select HAND in the UNITS menu and make the

required, different, K-factor calculations for the flowmeter, the (accumulated) total

and the flow rate settings by hand.

ACTION

RESULT

NOTICE

11. Press the PROG button

momentarily.

The PROG indicator

goes off.

The selection is

confirmed.

For the explanation,

the measurement unit m3 is

selected.

12. Press the ▲ button until

the K-FACTOR menu

shows.

the K-Factor menu

shows.

Read the (average) K-Factor from

the flowmeter certificate and select

the same K-Factor in this menu.

13. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the K-Factor as

given on the flowmeter certificate.

14. Press the ▲ button and

the ► button to make

the required selection.

The selection 6624605

shows (decimals are not

set yet).

For the explanation,

the K-Factor 6624605 is selected.

The 3 decimals are not shown yet!

15. Press the PROG button

momentarily.

The PROG indicator

goes off.

The selection is

confirmed.

16. Press the ▲ button until

the K-F DECS menu

shows.

The K-Factor decimals

menu shows.

17. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the decimal

pointer.

Read the K-Factor decimals from

the flowmeter certificate and select

the same amount of decimals in this

menu.

18. Press the ▲ button to

make the required

selection.

The selection 0.003

shows.

For the explanation,

the decimals for the K-Factor are

set to 3 decimals.

19. Press the PROG button

momentarily.

The PROG indicator

goes off.

The selection is

confirmed.

20. Press the ► button to

view the K-FACTOR

menu.

The K-Factor shows

6624.605.

The decimal pointer shows as set in

the K-F Decs menu.

21. Press the ▲ button until

the FLOWMETER

menu shows.

The FLOWMETER menu

shows.

E110-SERIES TUTORIAL AUTOMATIC UNIT CONVERSION

FW_E110_AutoUnitConv_002_EN Page 7

2.1.2 The automatic unit conversion - HAND mode

This procedure gives the information how to setup the HAND mode. The HAND mode is

selected when the required measurement unit is not supported by the automatic unit

conversion.

ACTION

RESULT

NOTICE

1. Press the PROG button

for at least 7 seconds.

The SETUP indicator

comes on continuously.

2. Wait for the setup menu

to show.

The setup menu shows.

3. Press the ► button until

the FLOWMETER

menu shows.

The FLOWMETER menu

shows.

In this menu you can match the

flowmeter with the E-series.

4. Press the ▲ button until

the UNITS menu

shows.

The UNITS menu shows.

The UNITS menu is used to make

a choice between the automatic

unit conversion modes.

5. Press the PROG button

momentarily.

The PROG indicator

comes on.

For measurement units which are

not supported, select HAND.

6. Press the ▲ button to

make the required

selection.

The HAND selection

shows.

For the explanation,

the mode HAND is selected.

7. Press the PROG button

momentarily.

The PROG indicator goes

off.

The selection is

confirmed.

8. Press the ▲ button to

make the required

selection.

The FLOWMETER menu

shows.

2.2 Set the reading for the (accumulated) total

This chapter explains the procedure how to setup the measurement unit for reading the

E-series.

2.2.1 The (accumulated) total - AUTO-VOL and AUTO MAS mode

This setting does not influence the K-Factor measurement unit as set from the flowmeter

certificate. The displayed measurement unit, as you selected, for the (accumulated) total is

calculated from the settings in the flowmeter menu.

NOTICE

This procedure is only applicable for the automatic unit conversion modes

AUTO-VOL and AUTO-MASS.

ACTION

RESULT

NOTICE

1. Press the ► button

until the TOTAL menu

shows.

The TOTAL menu shows

Now you can set the TOTAL

settings, but not the K-Factor Factor

(decimals) because these settings

are controlled by the FLOWMETER

settings.

2. Press the ▲ button until

the UNIT menu shows.

The UNIT menu shows.

3. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the measurement

unit for display purpose only. The

automatic unit conversion takes

care for the correct reading with

respect to the flowmeter calibration.

AUTOMATIC UNIT CONVERSION E110-SERIES TUTORIAL

Page 8 FW_E110_AutoUnitConv_002_EN

ACTION

RESULT

NOTICE

4. Press the ▲ button to

make the required

selection.

The selection US GAL

shows.

For the explanation,

the measurement unit for the

(accumulated) total is set to

US GAL.

5. Press the PROG button

momentarily.

The PROG indicator

goes off.

The selection is

confirmed.

The Flowmeter (K-factor) unit m3 is

automatically converted to show the

total in US Gallons.

6. Press the ▲ button until

the DECIMALS menu

shows.

The DECIMALS menu

shows.

7. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the decimal

pointer for display purposes only.

8. Press the ▲ button to

make the required

selection.

The selection 0.1 shows.

For the explanation,

the decimals for the (accumulated)

total are set to 1 decimal.

9. Press the PROG button

momentarily.

The PROG indicator

goes off.

The selection is

confirmed.

NOTICE

The K-factor and the K-factor decimals for the (accumulated) total shows as

AUTO because the automatic unit conversion controls these parameters.

NOTICE

If 7 digits is not sufficient to show the (accumulated) total, you can multiply the

reading by x10, x100, etc. This multiplication factor is set in the next menu.

ACTION

RESULT

NOTICE

10. Press the ▲ button until

the FACTOR X menu

shows.

The FACTOR X menu

shows.

11. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the multiplication

factor for the (accumulated) total

which require more than 7 digits.

12. Press the ▲ button to

make the required

selection.

The selection 10 shows.

For the explanation,

the multiplication factor for the

(accumulated) total.is set to 10x.

13. Press the PROG button

momentarily.

The PROG indicator

goes off.

The selection is

confirmed.

E110-SERIES TUTORIAL AUTOMATIC UNIT CONVERSION

FW_E110_AutoUnitConv_002_EN Page 9

2.2.2 The (accumulated) total - HAND mode

This procedure gives the information how to setup the HAND mode. The HAND mode is

selected when the required measurement unit is not supported by the automatic unit

conversion.

NOTICE

This procedure is applicable for the HAND mode where the K-Factor for the

(accumulated) total is set by hand. For the explanation, US GAL is the selected

measurement unit for the (accumulated) total.

ACTION

RESULT

NOTICE

1. Press the PROG button

until the TOTAL menu

shows.

The TOTAL menu shows.

In this menu you can setup the

reading for the (accumulated) total.

2. Press the ▲ button until

the UNIT menu shows.

the UNIT menu shows.

3. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the measurement

unit for the (accumulated) total.

A change of the measurement unit

requires also a new calculation of

the K-Factor for the (accumulated)

total. The calculation is not done

automatically!

4. Press the ▲ button to

make the required

selection.

The selection US GAL

shows.

For the explanation,

the measurement unit for the

(accumulated) total are set to

US GAL.

5. Press the PROG button

momentarily.

The PROG indicator goes

off.

The selection is

confirmed.

6. Press the ▲ button until

the DECIMALS menu

shows.

The DECIMALS menu

shows.

7. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the decimal

pointer for display purposes only.

8. Press the ▲ button to

make the required

selection.

The selection 0 shows.

For the explanation,

the decimals for the (accumulated)

total are set to 0 decimals.

9. Press the PROG button

momentarily.

The PROG indicator goes

off.

The selection is

confirmed.

10. Press the ▲ button until

the K-FACTOR menu

shows.

The K-FACTOR menu

shows.

Calculate the K-Factor for the

(accumulated) total by hand and

make a note.

11. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the calculated

K-Factor for the (accumulated)

total.

12. Use the ▲button and

the ►button to enter

the required data.

The K-FACTOR menu

shows 25.077.

For the explanation,

the K-Factor 6624.605 with an unit

m3converted into US GAL gives

6624.605 : 264.17 = 25.077.

AUTOMATIC UNIT CONVERSION E110-SERIES TUTORIAL

Page 10 FW_E110_AutoUnitConv_002_EN

ACTION

RESULT

NOTICE

13. Press the PROG button

momentarily.

The PROG indicator goes

off.

The selection is

confirmed.

14. Press the ▲ button until

the K-F DECS menu

shows.

The K-Factor decimals

menu shows.

15. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the decimal

pointer.

16. Press the ▲ button to

make the required

selection.

The selection 0 shows.

For the explanation,

the decimals for the K-Factor are

set to 0 decimals.

17. Press the PROG button

momentarily.

The PROG indicator goes

off.

The selection is

confirmed.

NOTICE

If 7 digits is not sufficient to show the (accumulated) total, you can multiply the

reading by x10, x100, etc. This multiplication factor is set in the next menu.

ACTION

RESULT

NOTICE

18. Press the ▲ button until

the FACTOR X menu

shows.

The FACTOR X menu

shows.

19. Press the PROG button

momentarily.

The PROG indicator

comes on.

Now you can set the multiplication

factor for the (accumulated) total

which require more than 7 digits.

20. Press the ▲ button to

make the required

selection.

The selection 10 shows.

For the explanation,

the multiplication factor for the

(accumulated) total is set to 10x.

21. Press the PROG button

momentarily.

The PROG indicator

goes off.

The selection is

confirmed.

2.3 Set the reading for the flow rate

This chapter explains the procedure how to setup the measurement unit for reading the E-

series.

2.3.1 The flow rate - AUTO-VOL and AUTO MAS mode

This setting does not influence the K-Factor measurement unit as set from the flowmeter

certificate. The displayed measurement unit, as you selected, for the flow rate is calculated

from the settings in the flowmeter menu.

NOTICE

This procedure is only applicable for the automatic unit conversion modes

AUTO-VOL and AUTO-MASS.

ACTION

RESULT

NOTICE

1. Press the ► button

until the FLOWRATE

menu shows.

The FLOWRATE menu

shows

Now you can set the FLOWRATE

settings, but not the K-Factor

(decimals) because these settings

are controlled by the FLOWMETER

settings.

Otros manuales para E Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Fluidwell

Fluidwell

Fluidwell D Series Manual de usuario

Fluidwell

Fluidwell F014-P Manual de usuario

Fluidwell

Fluidwell F011-P Manual de usuario

Fluidwell

Fluidwell F Series Manual de usuario

Fluidwell

Fluidwell F093-P Manual de usuario

Fluidwell

Fluidwell E126-P-EG Manual de usuario

Fluidwell

Fluidwell D Series Manual de usuario

Fluidwell

Fluidwell F Series Manual de usuario

Fluidwell

Fluidwell F070-U Manual de usuario

Fluidwell

Fluidwell F040-T Manual de usuario

Fluidwell

Fluidwell F Series Manual de usuario

Fluidwell

Fluidwell F110-A Manual de usuario

Fluidwell

Fluidwell F Series Manual de usuario

Fluidwell

Fluidwell F113-P-PD-OS Manual de usuario

Fluidwell

Fluidwell F018-P Manual de usuario

Fluidwell

Fluidwell F190-A-OS Manual de usuario

Fluidwell

Fluidwell F113-A Manual de usuario

Fluidwell

Fluidwell E Series Manual de usuario

Fluidwell

Fluidwell F012-A Manual de usuario

Fluidwell

Fluidwell F118-A Manual de usuario

Fluidwell

Fluidwell E115-P Manual de usuario

Fluidwell

Fluidwell F110-P Manual de usuario

Fluidwell

Fluidwell F011-P Manual de usuario

Fluidwell

Fluidwell F018-P Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario