Fluidmaster PerforMAX 400AH Manual de usuario

QUICK Install Guide

*See back page for important legal information.

INSTALL WITH CONFIDENCE

PerforMAX®

400AH FILL VALVE

GETTING STARTED

PARTS OVERVIEW

TOOLS NEEDED

Towel Bucket Sponge

Pliers

Locknut

Reﬁll Clip

Reﬁll Tube

Reﬁll Tube Clamp

Shank Washer

Tank Water Level

Adjustment Screw

Bowl Water Level

Adjustment Roller Clamp

Bowl Water Level

Adjustment Roller Clamp

Tank Water Level

Adjustment Screw

A: TURN OFF WATER

B: DRAIN WATER

Flush toilet to drain most of the water from the tank.

C: USE SPONGE OR TOWEL TO SOAK UP

EXCESS WATER IN TANK

FLUSH

STEP 1: PREPARE TANK

Towel

Sponge

LEFT

A: REMOVE CONNECTOR

Remove water supply

connector from bottom of ﬁll

valve by twisting connector

nut to the left (clockwise).

B: REMOVE OLD LOCKNUT

Below tank, twist locknut

to the left (clockwise) to

remove from ﬁll valve.

C: REMOVE OLD FILL VALVE

Drain any excess water

into bucket by removing ﬁll

valve from tank.

(Pull ﬁll valve up)

STEP 2: REMOVE OLD FILL VALVE

Bucket

(Optional)

Pliers

(Optional)

TURN

CLOCKWISE

6 7

STEP 3: ADJUST HEIGHT OF NEW FILL VALVE

FOR STANDARD FLUSH VALVES

HOLD

TWIST

LEFT

TOP OF FILL VALVE CAP

TOP OF OVERFLOW PIPE

Overﬂow Pipe

Fill Valve Cap

TOP OF FILL VALVE CAP

TOP OF OVERFLOW PIPE

FOR CANISTER FLUSH VALVES

A: TWIST FILL VALVE TO ADJUST HEIGHT

Top of ﬁll valve cap should measure roughly 3"

above top of overﬂow pipe.

8 9

STEP 4: INSTALL NEW FILL VALVE

A: INSTALL SHANK WASHER

Pull up to top of shank.

* Place shank washer

onto threaded shank of

ﬁll valve. WIDE SIDE UP.

C: ATTACH REFILL CLIP

TO OVERFLOW PIPE

E: INSTALL LOCKNUT

Screw locknut to the

right (counterclockwise)

onto ﬁll valve shank

(below tank). RIGHT

B: PUSH REFILL TUBE ONTO

REFILL PORT FIRST

Squeeze tube clamp arms and

move it towards reﬁll port.

D: INSERT FILL VALVE

Position reﬁll tube to face

overﬂow pipe.

F: ATTACH REFILL TUBE TO REFILL CLIP

Squeeze tube clamp arms and move it towards reﬁll clip.

Note: If reﬁll tube is too long, cut tube.

Standard Flush Valves

Canister Flush Valves

Reﬁll

Clip

Overﬂow

Pipe

Reﬁll Tube

Reﬁll

Clip

Reﬁll Tube

Overﬂow

Pipe

Shank Washer

Threaded Shank

10 11

FOR CANISTER FLUSH VALVES

A: ATTACH WATER

SUPPLY CONNECTOR

TO FILL VALVE

Twist to the right

(counterclockwise)

RIGHT

C: WATER LEVEL

After the tank stops ﬁlling, water level should ﬁll the tank to

roughly ½ inch below top of overﬂow pipe to ensure a

proper ﬂush.

See diagrams on next page.

STEP 5: FINISHING STEPS

FOR STANDARD FLUSH VALVES

TURN

COUNTER-

CLOCKWISE

See page 12 to ﬁne-tune

TANK Water Level

1/2"

Overﬂow Pipe

Top of

Overﬂow Tube

Water Level

1/2"

Overﬂow

Pipe

Top of

Overﬂow Pipe

Water Level

TOP DOWN VIEW

B: TURN ON WATER

Check for leaks.

(See Troubleshooting for

leak solutions)

12 13

STEP 6: FINE-TUNE TANK WATER LEVEL

A: FLUSH THE TOILET TO CHECK

THE TANK WATER LEVEL

After the water stops ﬁlling the tank,

the water level should be roughly ½

inch below the top of overﬂow pipe to

ensure a proper ﬂush.

B: WATER LEVEL IS TOO LOW

Turn the tank water level adjustment screw

clockwise to raise the ﬂoat. Flush to reset

water level.

WATER LEVEL IS TOO HIGH

Turn the water level adjustment screw

counterclockwise to lower the ﬂoat. Flush

to reset water level.

1/2"

Overﬂow Pipe

FOR CANISTER FLUSH VALVES

FOR STANDARD FLUSH VALVES

1/2"

Overﬂow Pipe

Top of

Overﬂow Pipe

Water Level

Tank Water Level

Adjustment Screw

Float

1/2"

Overﬂow

Pipe

Top of

Overﬂow Pipe

Tank Water Level

Adjustment Screw

Water Level

Float

WATER

LESS

WATER

–

Tank Water Level

Adjustment Screw

14 15

STEP 7: FINE-TUNE BOWL WATER LEVEL

A: FILL BOWL WITH A

GALLON OF WATER

Wait 1 minute until the bowl

water level recedes down and

stops.

E: FLUSH TOILET, CHECK

BOWL WATER LEVEL

Repeat Steps 7D and 7E until

water level in bowl matches

the line when the ﬁll valve

shuts off.

B: MARK THE WATER LEVEL

IN THE BOWL

With a pencil, draw a line at the

top of the water level in bowl.

C: FLUSH TOILET TO CHECK

BOWL WATER LEVEL

If the water level matches the line

you’ve made in the bowl when the

ﬁll valve stops ﬁlling the tank, the

water level is correct, proceed to

Step 8.

D: ADJUST THE BOWL WATER LEVEL

NOTE: “0” on roller clamp equals no reﬁll to bowl.

TOO HIGH

TOO LOW

If the water level matches the line in

the bowl and the ﬁll valve is STILL

FILLING, then the bowl water level is

TOO HIGH, proceed to Step 7D.

If the valve shuts off and the water

level does NOT match the line in the

bowl, the water level is TOO LOW,

proceed to Step 7D.

TOO HIGH =

TOO LOW =

Turn roller clamp with thumb

to the next LOWER number.

Turn roller clamp with thumb

to next HIGHER number.

16 17

STEP 8: FLUSH THE TOILET

Still not working exactly right?

See the next page for Troubleshooting.

YOU DID IT!

We knew you could!

Share your success story

with friends and family!

#FixedMyToilet

#Fluidmaster

A: FLUSH THE TOILET

If you’re satisﬁed with the ﬂush, YOU’RE DONE!

18 19

TROUBLESHOOTING

TURN

COUNTER-

CLOCKWISE

See Our Troubleshooting

HOW-TO VIDEO

http://bit.ly/2yAdZn7

VIDEO

IF THE FILL VALVE:

• DOES NOT TURN ON

• WON’T TURN OFF

• WON’T REFILL TANK

REMOVE CAP AND CHECK FOR DEBRIS

A: Turn off water supply.

B: Flush toilet.

C: With right hand push ﬂoat up, grip and

hold shaft under ﬂoat.

D: With left hand twist cap and lever arm

counterclockwise to unlock cap. Let

cap hang on ﬂoat cup.

E: Hold empty cup upside down over

uncapped valve to prevent splashing.

F: Turn water supply on and off a few

times.

G: Turn water supply off.

H: Replace valve cap.

• Place cap assembly on top of gray

valve body by aligning cap arm and

adjustment rod next to reﬁll tube.

• Press down on top cap while rotating

top & arm clockwise to locked position.

IF THE FLOAT DOES NOT DROP WHEN FLUSHED

IF THE FILL VALVE TURNS ON AND OFF BY ITSELF

IF WATER SUPPLY CONNECTOR IS LEAKING

REPLACE FILL VALVE SEAL

CLEAN FLAPPER AND DRAIN SEAT

A: Remove cap (see page 18).

B: Replace seal with a genuine

Fluidmaster 242 Seal.

C: Replace valve cap.

A: The tank is losing water, clean the

ﬂapper and drain seat for a better

seal.

B: Replace ﬂapper.

C: If leak continues after replacing

ﬂapper, replace ﬂush valve (507AK,

or 540AKR) or repair ﬂush valve seat

(555C).

A: Replace water supply line.

• Place cap assembly on top of gray

valve body by aligning cap arm and

adjustment rod next to reﬁll tube.

• Press down on top cap while

rotating top & arm clockwise to

locked position.

Tabla de contenidos

Otros manuales de Unidad de control de Fluidmaster

Fluidmaster

Fluidmaster PerforMAX 400CAR3 Manual de usuario

Fluidmaster

Fluidmaster 200AM133 Manual de usuario

Fluidmaster

Fluidmaster PerforMAX 400H Manual de usuario

Fluidmaster

Fluidmaster 402CARHR Manual de usuario

Fluidmaster

Fluidmaster 560AU Manual de usuario

Fluidmaster

Fluidmaster 400A Manual de usuario

Fluidmaster

Fluidmaster 402CARHR Manual de usuario

Fluidmaster

Fluidmaster 400AC Manual de usuario

Fluidmaster

Fluidmaster PerforMAX 400H-002 Manual de usuario

Fluidmaster

Fluidmaster 400A Manual de usuario

Fluidmaster

Fluidmaster 400LS Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario