FLIR EXTECH INSTRUMENTS MA120 Manual de usuario
User’s Guide
Model MA120
200A AC/DC Mini Clamp-on Meter
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
MA120 Ver. 1.2 10/2004
2
Introduction
Congratulations on your purchase of Extech’s MA120 AC/DC Mini Clamp Meter. This professional
meter, with proper care, will provide years of safe reliable service.
Meter Description
1. Current sense jaw
2. Non-contact AC voltage indicator light
3. Flashlight button
4. Rotary function switch
5. Data HOLD and Backlight key
6. LCD display
7. Clamp trigger
8. One-touch DCA ZERO key
Safety Information
!Caution! Refer to the explanation in this Manual
Double Insulation
This meter has been designed to be safe in use, but the operator must use caution in its operation.
The rules listed below should be carefully followed for safe operation.
1. NEVER apply voltage or current to the meter that exceeds the specified maximum:
2. USE EXTREME CAUTION when working with voltages greater than 60VDC or 25VAC rms.
These voltages are considerd a shock hazard.
3. NEVER operate the meter unless the back cover and the battery/fuse door are in place and
fastened securely.
Input Limits
Function Maximum Input
AC Current 200A
DC Current ±200A
Frequency 1kHz
1
23456
7
8
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
MA120-V1.3-EN-3/12
3
Operation
AC Current Measurements
1) Set the Function switch to the ACA range.
2) Press the jaw trigger and clamp around, fully enclosing a single conductor.
Do not allow a gap between the two halves of the jaw. Refer to the diagram
at right for the correct way to enclose a single conductor.
3) Read the ACA value on the LCD.
DC Current Measurements
1) Set the Function switch to the DCA range.
2) Press the ZERO key to null the meter display.
3) Press the Trigger to open the current sense Jaw.
4) Fully enclose the conductor to be measured. Do not allow a gap between the two halves of the
jaw.
5) Read the DCA value on the LCD.
Non-Contact AC Voltage Detection
1) AC Voltage detection operates on any of the four Function switch positions.
2) Touch the probe tip to the hot conductor or insert into the hot side of the electrical outlet.
3) If AC voltage is present, the detector light will illuminate.
NOTE: The conductors in electrical cord sets are often twisted. For best results, slowly slide the
probe tip along a length of the cord to assure placing the tip in close proximity to the live
conductor.
NOTE: The detector is designed with high sensitivity. Static electricity or other sources of energy
may randomly turn the detector light on. This is normal operation
Frequency Measurements
1) Set the Function switch to the Hz position.
2) Fully enclose the conductor to be measured. Do not allow a gap between the two halves of the
jaw.
3) Read the Frequency value on the LCD.
Flashlight
Press and hold the top button to turn the flashlight on. Release the button to turn the flashlight off.
Data Hold
To freeze the current reading on the LCD, press the “Hold / Backlight” key. The word HOLD will
appear on the LCD while the meter is in the Data Hold mode. To release the Data Hold function and
return the meter to normal operation, press the “Hold / Backlight” key again. The word HOLD will
switch off.
Backlight Display
Press and hold the “Hold / Backlight” key for more than 2 seconds to turn on the backlight. This will
also activate the Data Hold function. To release the Data Hold function and return the meter to normal
operation, press the Data Hold key momentarily. To turn off the backlight, press and hold the “Hold
Backlight” key for more than 2 seconds.
Yes
No
WARNING: Risk of Electrocution. Before use, always test the Voltage Detector on a
known live circuit to verify proper operation
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
MA120-V1.3-EN-3/12
4
Specifications
General Specifications
Display 3-2/3 (2400 count) Digit LCD with white LED backlight
Polarity Minus sign ( - ) indicates negative polarity
Current sensor Hall effect sensor type
Overload indication “OL” displayed on the LCD
DCA zero adjust One touch zero key
Display rate 2 readings/second, nominal
Battery Two 1.5V AAA batteries
Low Battery indication “BATT” displayed on the LCD
Operating conditions 32ºF to 86ºF (0ºC to 30ºC) 90%RH; 86ºF to 104ºF (30ºC to 40ºC) 75%RH;
104ºF to 122ºF (40ºC to 50ºC) 45%RH
Storage conditions - 14ºF to 140ºF (-30ºC to 60ºC); < 90% Relative Humidity
Altitude Operate at less than 3000 meters
Weight 6.2 oz. (176g) including battery
Dimensions 6.5 x 2.6 x 1.3” (164 x 65 x 32mm) (HWD)
Jaw opening 0.7” (18mm)
Standards IEC 1010 Category III 300V, Category II 600V,
Range Specifications
Function Range Resolution Accuracy (of reading)
DC Current 200A 0.1A ± (2.8% + 8 digits)
AC Current 200A 0.1A ±(3.0% + 8 digits)
40-51Hz 0.01Hz
51-510Hz 0.1Hz
Frequency
(Auto-Ranging)
0.51-1kHz 0.001kHz
±(1.2% + 5 digits)
Input Sensitivity: 2.5A AC RMS min.
Non-Contact AC Voltage 100VAC to 600VAC 50/60Hz
C
C
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Este manual sirve para los siguientes modelos
1
Otros manuales de Multímetro de FLIR
FLIR
FLIR Extech Instruments MG302 Manual de usuario
FLIR
FLIR DM93-2 Manual de usuario
FLIR
FLIR DM286 Manual de usuario
FLIR
FLIR MR160 Manual de usuario
FLIR
FLIR CM83 Manual de usuario
FLIR
FLIR DM91 Manual de usuario
FLIR
FLIR Extech Instruments MultiMaster MM560A Manual de usuario
FLIR
FLIR IM75 Manual de usuario
FLIR
FLIR Extech Instruments 380941 Manual de usuario
FLIR
FLIR DM93 Manual de usuario
FLIR
FLIR DM90 Manual de usuario
FLIR
FLIR IM75-2 Manual de usuario
FLIR
FLIR DM93-2 Manual de usuario
FLIR
FLIR Extech Instruments MN16 Manual de usuario
FLIR
FLIR EXTECH INSTRUMENTS EX520 Manual de usuario
FLIR
FLIR DM90 Manual de usuario
FLIR
FLIR EXTECH INSTRUMENTS DM110 Manual de usuario
FLIR
FLIR Extech EX505 Manual de usuario
FLIR
FLIR DM166 Manual de usuario
FLIR
FLIR Extech EX510 Manual de usuario
Manuales populares de Multímetro de otras marcas
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manual de usuario
PeakTech
PeakTech 4000 Manual de uso y cuidado
YOKOGAWA
YOKOGAWA 90050B Manual de usuario
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manual de usuario
Fluke
Fluke 8846A Manual de operación y mantenimiento
Tempo Communications
Tempo Communications MM200 Manual de usuario
