FLIR Elara FR-345-EST Manual de usuario
Elara FR-345-EST QIG Rev 110
December 2020
This document does not contain any export-controlled information.
Elara™ FR-345-EST
Quick Install Guide
1 Check Contents
Make sure all of the items above are included in the camera kit.
2 Select a Location
Select a suitable location to mount the camera.
The focus for both of the camera's sensors is fixed at one meter (39.4"). If it will be
used in EST screening mode, make sure to install the camera so that the faces of
persons being screened for EST are 1m ± 0.2m (39.4" ± 7.9") away from the front
of the camera.
Verify that the operating temperature is 15°C to 45°C (60°F to 110°F), 0-95%
relative humidity. The camera provides optimal performance in a stable
environment near 22°C (72°F).
For further advice on positioning and orienting the camera, see the camera's
installation and user guide.
3 Configure the Camera
FLIR recommends configuring the camera on a bench or in a lab before mounting
and aiming it. However, it is also possible to configure the camera after mounting
it, which could be more appropriate for certain installations.
3.1 Install the FLIR DNA tool
To discover the camera on the network, FLIR recommends using the FLIR
Discovery Network Assistant (DNA) tool. Version 2.3.0.19 or higher supports Elara
FR-345-EST, does not require a license to use, and is a free download from
Elara FR-345-EST QIG Rev 110
December 2020
This document does not contain any export-controlled information.
FLIR.com > Products > Security > FLIR EST Thermal Screening Solutions > FLIR
Elara™ FR-345-EST > Support > Resources.
3.2 Connect the Camera
System Cable
a. Attach an Ethernet cable to the RJ45
connector for a 10/100 Mbps Ethernet
and PoE+ (Power over Ethernet)
IEEE 802.3at connection.
Make sure the camera and the PC
you are using to configure the
camera are on the same LAN
segment.
b. Connect the alarm connectors, if
needed.
c. If using an external 12 VDC or 24
VAC power supply, connect its wires
to the two-pin power terminal block.
Then, insert the terminal block into
the power connector.
Connector
1
Black
RJ-45
2
Black
12-30 VDC (±10%) /
24 VAC (21-28 VAC) -
Red
12-30 VDC (±10%) /
24 VAC (21-28 VAC) +
3
Yellow
NOT USED
Orange
NOT USED
Purple
NOT USED
Green
NOT USED
Red
ALARM IN signal
Black
ALARM IN GND
Brown
ALARM OUT signal
Blue
ALARM OUT COM
3.3 Configure for Networking
You can configure the camera for networking using the DNA tool, the camera's
web page, or a supported VMS.
DNA tool
Camera's web page
Discover camera IP address
•
Configure IP address, mask, and gateway
•
•
Configure DNS settings, MTU, and Ethernet speed
•
Change user credentials
•
•
Configure more than one camera at the same time
•
For information about using the supported VMS to configure the camera, see the
VMS documentation.
By default, DHCP is enabled on the camera and a DHCP server on the network
assigns the camera an IP address. For example, if the camera is managed by
FLIR's Horizon or Meridian VMS and the VMS is configured as a DHCP server, the
VMS automatically assigns the camera an IP address.
Elara FR-345-EST QIG Rev 110
December 2020
This document does not contain any export-controlled information.
If the camera is managed by FLIR’s Latitude VMS or is on a network with static IP
addressing, you can manually specify the camera’s IP address using the DNA tool
or the camera's web page. The camera's default IP address is 192.168.0.250.
To manually specify the camera's IP address using the DNA tool:
a. Run the DNA tool (DNA.exe) by double-clicking .
The Discover List
appears, showing
compatible
devices on the
LAN segment and
their current IP
addresses.
In the DNA Discover List, verify that the camera's status is Online.
If this is the first time you are configuring the camera or if it is the first time after
resetting the camera to its factory defaults, DNA automatically authenticates
the camera with the default password for the camera's admin user (admin).
If the admin user password has been
changed, you need to authenticate the
camera.
In the DNA Discover List, right-click the
camera and select Login.
In the DNA - Login window, type the
password for the admin user. If you do
not know the admin user password,
contact the person who configured the
camera's users and passwords.
Click Login, wait for Ok status to
appear, and then click Close.
In the DNA Discover List, verify that the camera's status is Authenticated.
b. Change the camera’s IP address.
Right-click the camera and select IP Setup.
Elara FR-345-EST QIG Rev 110
December 2020
This document does not contain any export-controlled information.
In the DNA - IP Setup window, clear
Use DHCP and specify the camera's IP
address. You can also specify the Mask
(default: 255.255.255.0) and Gateway.
Then, click Update, wait for Ok
status to appear, and then click Close.
4 Install the Camera
The camera can be mounted directly on a wall or a ceiling, or it can be mounted
using the CB-WLBX-G4 Wall & Surface Mount Kit, which includes a junction box.
For the full list of mounting and other accessories available for the camera, see the
FLIR Security Cameras - Accessory Guide.
4.1 Fit Mounting Hardware
If using the CB-WLBX-G4 Wall & Surface Mount Kit with junction box, install it
according to the installation guide for that accessory.
If using other mounting hardware, install the mounting hardware for the camera
according to instructions.
4.2 Prepare the Surface for Mounting
Be sure to have the required accessories
and tools available.
Refer to the camera's installation and
user guide as necessary.
a. Attach the mounting template sticker
onto the wall or ceiling where you are
mounting the camera.
b. Drill six anchor holes according to the
template.
c. Hammer the six plastic anchors into
the drilled holes.
d. If the system cable is going to exit
from the rear, drill a hole in the center
of the mounting template for the
cable.
The system cable can exit either from
the side of the camera's mounting
bracket or through the hole in the
back of the mounting bracket.
Side cable exit
Elara FR-345-EST QIG Rev 110
December 2020
This document does not contain any export-controlled information.
Rear cable exit
4.3 Route Cables and Connect the Camera
a. If you are using a mounting accessory, install the power and network cabling in
the mounting hardware so that it is accessible when the camera is mounted.
b. Attach an Ethernet cable from the network switch to the RJ45 connector.
c. Connect the alarm connectors, if needed.
d. If using an external 12 VDC or 24 VAC power supply, connect its wires to the
two-pin power terminal block. Then, insert the terminal block into the power
connector.
4.4 Mount and Aim the Camera
a. Place the camera over the surface
and securely fasten the T10 self-
tapping screws clockwise into the
plastic anchors.
Make sure that the camera’s general
orientation covers the required field
of view.
b. Aim the camera.
Support the camera's weight with
your hand. Then, loosen the three
locking screws and adjust the
camera's pan, tilt, and rotation.
Important
While aiming the camera, make sure to support the
camera's weight with your hand.
Tip
FLIR recommends aiming the camera while monitoring the
camera's live video on the camera web page or in a video stream.
Elara FR-345-EST QIG Rev 110
December 2020
This document does not contain any export-controlled information.
c. Make sure that the toothed surfaces
are properly aligned and meet
evenly. Then, use the T10 torx
wrench to securely tighten each
locking screw.
5 Boresight the Camera
The admin user or any user assigned the admin or expert role
can boresight the camera using the camera's web page, which
supports Google Chrome (recommended), Firefox, Microsoft
Edge, and Internet Explorer 11 (32-bit), on PCs running 64-bit
Windows 7, 8, 8.1, or 10.
a. In the DNA Discover List, double-click the camera.
b. On the login screen, type a user name and password. Both
are case-sensitive.
When logging in to the camera's web page for the first time or for the first
time after resetting the camera to its factory defaults, type admin for the user
name and for the password.
Then, specify a new password for the admin user. Use a strong password
consisting of at least eight characters and at least one uppercase letter, one
lowercase letter, and one number. Passwords can include the following
special characters: |@#~!$&<>+_-.,*?= .
Log back in using the new password.
The camera's View Settings Home Page opens.
c. Click System Settings > Boresight. The Boresight page opens.
d. Using the digital pan, tilt, zoom, and crosshair controls, align the
visible video image with the thermal video image.
e. Click Save.
Elara FR-345-EST QIG Rev 110
December 2020
This document does not contain any export-controlled information.
Important
After powering up the camera, wait 30 minutes before
commencing screening. The camera's thermal sensor needs to
stabilize. In System Settings, click Firmware & Info, and make
sure the Temperature is stable.
For information about using the camera's web page to perform additional
configuration steps, see the camera's installation and user guide.
6 Attach the Camera to a Supported VMS
After you have mounted the camera and discovered or defined its IP address, you
can use VMS Discovery/Attach procedures to attach the camera to a supported
VMS.
7 Camera Dimensions
The Elara FR-345-EST camera’s dimensions are:
Side View
Front View
8 Register the Product
Register your Product with FLIR at https://customer.flir.com.
For warranty information, see https://www.flir.com/support-
center/warranty/security/flir-security-product-warranties/.
9 Contact Information
FLIR Systems, Inc.
6769 Hollister Avenue
Goleta, CA 93117
USA
Support: https://www.flir.com/support/
Corporate Headquarters
27700 SW Parkway Ave.
Wilsonville, OR 97070
USA
Otros manuales para Elara FR-345-EST
1
Tabla de contenidos
Otros manuales de Cámara digital de FLIR
FLIR
FLIR USB3 Vision CHAMELEON 3 Manual de usuario
FLIR
FLIR A400 Series Manual de usuario
FLIR
FLIR AX Series Manual de usuario
FLIR
FLIR X-Series Manual de usuario
FLIR
FLIR Txxx series Manual de usuario
FLIR
FLIR C2 Manual de usuario
FLIR
FLIR USB3 Vision Flea3 Manual de usuario
FLIR
FLIR Alpha Nir Manual de usuario
FLIR
FLIR M500 Manual de usuario
FLIR
FLIR M-Series Manual de usuario
FLIR
FLIR A400 Series Manual de usuario
FLIR
FLIR Exx series Manual de usuario
FLIR
FLIR A6 Series Manual de usuario
FLIR
FLIR Lorex LW3211-C Manual de usuario
FLIR
FLIR ZENMUSE XT2 Manual de usuario
FLIR
FLIR Tau CNV Manual de usuario
FLIR
FLIR Quasar Gen III CP-6302 Series Manual de usuario
FLIR
FLIR ThermaCAM QuickView Manual de usuario
FLIR
FLIR CP-4221-300 Manual de usuario
FLIR
FLIR Ariel CM-3102 Manual
